Search Documents

Analysis of the topography associated with large vertical strains measured in the upper crust in the Basin and Range and elsewhere in the US Cordillera shows that it varies systematically with upper crustal strain such that it decreases where tectonism has resulted in relative thinning. The magnitude of topographic deflection suggests that the amount of thickening or thinning of the upper crust cannot also be reflected in vertical motions of the Moho discontinuity, nor can the vertical strain be isostatically accommodated by inflow or outflow of asthenosphere, mantle lithosphere or mafic lower crust. Simple isostatic calculations show that the compensating medium had a density probably within 100-200 kg/m of average upper continental crust, thus indicating that the compensating medium lies within the crust and is probably in large part quartzose. This conclusion is in accord with laboratory experiments on the strengths of rocks, and with reflection seismograms in deformed regions which suggest that the Moho is generally flat beneath regions of extreme gradients in upper crustal vertical strain. The upper crust floats on a quartzose layer in the mid-crust which, under orogenic conditions, is apparently so weak that it behaves as a relatively inviscid fluid at geologic timescales (> 10,000 a) and subcontinental lengthscales (100-1000 km).

Jan 1, 1990

By J Palaci, M MelTndez, F Parra, I Rojas

At the Huasco Pellet Plant of Compa±fa de Aceros del Pacffico, Chile, the production of iron concentrate suitable for pellet feed from a low-grade iron ore was technically evaluated. In this study, three treating schemes including comminution, magnetic concentration and flotation in pneumatic cells were tested. The best results were obtained at the laboratory scale by flotation technique using Lilaflot D 817 M as the collector without using any depressant. The operational parameters were determined including pneumatic flotation, and three circuits, two including magnetic pre-concentration, with the low-grade iron ore. The best results were obtained by size reduction at 80 per cent under 325 Tyler mesh, three steps of magnetic concentration and three steps of flotation in pneumatic cells. The magnetic concentrate contained 63.02 per cent of iron and 6.6 per cent of silica, and after the pneumatic flotation the iron content increased up to 70.18 per cent and silica decreases to 1.07 per cent with 78.78 per cent of iron recovery at a weight recovery of 31.89 per cent. Therefore, it is possible to use low-grade iron ore to produce pellet feed from magnetic concentrates by using reverse iron flotation in pneumatic cells.

Jan 1, 2005

In June 1996, Nord Resources Pacific (Nord) decided to work towards obtaining all necessary approvals from the government of PNG for a mine on Simberi Island in the Tabar Island Group, New Ireland Province. On the 9th of September 1996, Nord submitted a Proposal for Development and an application for a Mining Lease to mine the oxide gold deposits on Simberi Island. The Mining Lease was granted on the 3rd of December 1996 in a signing ceremony on Simberi Island. This was achieved in the extremely short time frame of less than 3 months and this paper attempts to explain the processes which made it possible.

Jan 1, 1997

By J-S Zhang

In this paper, the author briefly introduces the resource characteristics of Chinese iron ore, as well as the present increasing market demand for iron concentrate. The SHP-3200 wet high-intensity magnetic separator (HIMS) is used to separate complicated weak-magnetic iron ores being composed of specularite, limonite and siderite in Jiuquan Iron and Steel (Group) Co Ltd. Some technologies have been used to improve SHP-3200 HIMS, including modifying the angle of magnetic polar from 90¦ to 83¦, cooling the exciting coils by oil instead of air, adding reverse-washing equipment to wash off magnetic particles and adjusting the tooth-space of the matrix from 5.0 mm to 3.5 mm or 2.5 mm to enhance the recovery of fine particles. It is still difficult to meet the requirement for recovering more difficultly separated iron and the demands for high-grade concentrate of iron. In order to improve the recovery of difficult-separated iron, the film-magnetic separation technique is applied into the HIMS and a new LY matrix is designed to form magnetic gradient vertically. A flowing-film feeder is also added and the feed mouth is modified to make a slurry flow formed in the form of film along the wall of matrix. The microstructure and dissemination character of the mineral particles is studied, and the specific susceptibility of the primary minerals is measured. Then the distributive characteristics of a magnetic field for the separator with film-magnetic technique and the motion of particles in the process of separation are all analysed. By introducing the film-magnetic separation technique to SHP-Φ700 HIMS, the recovery of iron can be raised from 69.45 per cent to 76.07 - 78.96 per cent with the similar grade of concentrates of iron. Such an increase of 9.51 per cent in the recovery also shows that it is feasible for such film-magnetic separation technique to be applied into HIMS.

Jan 1, 2005

By Haslam C. O, Taylor S

Four historical periods of Australian lead-zinc-silver exploration and development are identified.In the first period, 1841-1900, Australia's deeply weathered surface yielded bonanza deposits. The outcrops of easily worked secondary ores, enriched in silver and lead, were discovered by prospectors with the incentive of production at times of high silver price. Districts discovered in this period still contributed, in 1982, 60 per cent of Australia's lead-zinc production, mainly from Broken Hill.The second period 1901-1944, was one of strong mine development but stagnant lead-zinc-silver exploration. Mount Isa was discovered and developed, but otherwise effort was devoted mainly to the mining of deposit extensions and to the metallurgical flotation of zinc. The deposit discovery rate was low but the discovery of Mount Isa was so significant that discoveries of this period contributed, in 1982, 30 per cent of Australia's lead-zinc production.The third period 1945-1972 was one of re-invigorated exploration.New geological and geophysical surveys, developing concepts of ore genesis, and worldwide comparisons of orebody settings improved target area selection. Evolving remote sensing methods, and rapid analytical techniques, assisted detection of lead-zinc deposits. Initiation of exploration led to discovery:1. in regions of previously unsuspected lead-zinc-silver potential (Sorby Hills, Mons Cupri, Golden Grove).2. of poorly exposed deposits in recognized mineral districts (Hilton, H.Y.C., Woodlawn, Elura, Que River).3. during active exploration for another commodity (Brown's, Woodcutters, Mary River, Beltana, Lady Loretla and Pegmont).The period saw a sustained growth in lead-zinc-silver production mainly from established operations. Mines discovered during the third period contributed, in 1982, 7 per cent of Australia's lead-zinc production.In the fourth period from 1973 to the present, exploration initiatives became fewer but resulted in continued discovery of poorly exposed deposits at Teutonic Bore, Thalanga, Benambra, Scuddles, Hellyer, and Jillawarra. Development initiatives strengthened in the period and production commenced at Woodlawn, Teutonic Bore, Que River and Elura; pre-feasibility work commenced at Scuddles, Hilton, Lady Loretta and Thalanga.

Jan 1, 1984

By K Zhao, H Gong, B Li

Health and safety are the first priority for Australian minerals sector. Australia has a global reputation in the mining industry. However, accidents occur every year. Legislation and regulation are important to prevent the accident from occurring, so do the new technologies. It is sad to witness the collision incident persisting and the long called collision avoidance system (CAS) is still not widely used in underground mines. The main reason is that the existing systems are still not advanced enough. The current CASs utilise GPS, infrared, ultrasonic, RFID, Radar, electromagnetic etc have their limitations and disadvantages. For instance, GPS is widely used in a surface mine, but it cannot be applied in underground mine; Infrared and electromagnetic have the false positive problem.

Sep 1, 2024

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By M G. Shaw, M A. Rhamdhani, S P. Singh, A R. Duffy, B Eisenbart, A K. Shukla, G A. Brooks

The field of astrometallurgy is a growing area of study. Metal production on the Moon is likely to begin in less than a decade as major space agencies such as NASA (National Aeronautics and Space Administration) and CNSA (China National Space Administration) are preparing to construct permanent lunar bases. The utilisation of regolith to generate oxygen and metals is expected to be important in the development of a sustainable lunar habitat. This paper provides an overview of potential metallurgical processing methods for lunar conditions, emphasising the impact of lunar factors on slag chemistry. The interaction between regolith and the extracted metals, as well as their impact on slag composition and refractory performance, are critical considerations in metal production on the lunar surface. The initial research on lunar metallurgical technologies is focused on oxygen extraction and Fe-Si alloys are reported as the by-products of these processes. This paper delves into the fundamental thermodynamics associated with the carbothermic reduction of lunar regolith. Thermodynamic analysis using the FactSage™ ver 8.2 software package indicates that the Fe-Si alloy can be produced as a metallic product from the lunar regolith at temperatures ranging from 1400°C to 1600°C under terrestrial conditions. However, under ultra-high vacuum conditions (3 × 10-15 bar) on the Moon, the required operating temperature for producing ferrosilicon would be significantly reduced. Thermodynamic modelling results indicate that under lunar vacuum conditions, Fe-Si alloys only exist as solid phases at lower temperatures below 650°C. At higher temperatures, both Fe and Si are expected to be present in the gas phase. In this work, the carbothermic reduction of the Lunar Mare Simulant (LMS-1) is conducted under terrestrial conditions. The findings indicate that the process can readily yield Fe-Si alloys with 7–10 wt per cent Si at 1600°C. Additionally, energy dispersive spectroscopy (EDS) analysis of the resulting Fe-Si alloy indicates the presence of phosphorus up to 1 wt per cent.

Aug 21, 2024

By Miller JD, Ye Y

The Air-Sparged Hydrocyclone (ASH) has been developed for the fast and efficient flotation of fine mineral particles in a centrifugal field during the past decade at the University of Utah. Over the years, the air-sparged hydrocyclone unit has shown promising potential for the flotation of copper porphyry ore, low-grade placer gold and auriferous pyrite ores, various industrial minerals, and fine coal cleaning. Many fundamental studies including the X-ray computed tomography (CT) analysis have been carried out in order to understand the multiphase fluid flow phenomena associated with ASH flotation. With data available from these studies, it is now possible to construct more accurate ASH flotation models for different applications in order to analyse the behaviour of the system and to optimise design and operating variables. The ASH flotation model developed in this paper is based on the data given in `Air-Sparged Hydrocyclone/Advanced Froth Flotation Fine Coal Cleaning', Final Report, DOE Contract No DE-AC-88PC88853, submitted by Pennsylvania Electric Company (PENELEC), December 1989. Data from several hundred experiments with the two-inch ASH-2C air-sparged hydrocyclone (capacity 0.1 - 0.3 tph dry coal) are available from the report and have been used for this analysis. In the past, a preliminary model based on limited data had been developed. The current study, however, emphasises the global behaviour of the ASH system by utilising almost all the data from the report for the purpose of scale-up and industrial application. There are two parts in the current modeling and analysis effort for ASH flotation of fine coal. The first part is the modeling/analysis of dimensionless ratio of overflow opening area to underflow opening area, A*, and the dimensionless ratio of air flowrate to slurry flowrate, Q . The second part involves the modelling/analysis of all other variables in the system and an expert system for operation and control is introduced.

Jan 1, 1993

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By B Beale

Bow-tie analysis is a commonly used tool in the Major Hazard Facility sector to identify, display and control risks that have the potential to pose serious harm to personnel. It is a simple but powerful risk management tool that displays traditional risk assessment outputs as easily interpreted ‘bow-tie diagrams’. These are an effective and versatile communication format that can be applied to any type of risk (eg safety, environmental, assets etc) and as such show great benefit in managing operational hazards in mining.

May 5, 2022

The Fiji islands are the world's most ac- cessible Cenozoic remnant arc. They provide occasional subaerial exposures of an arc frag- ment some 750 km long and 80 km wide, or about the size of the NE Japan volcanic arc. The fragment is one part of the former Vitiaz Arc which once connected Fiji to Vanuatu and Tonga. The Fijian portion has the most completely stu- died Tertiary section which contains a history of arc volcanism from the late Eocene to late Miocene (the Early and Mature Arc stages), a rich diversity of subsequent magmatic responses to the most recent episode of arc rifting (Ear- ly Rifting stage), and an example of transition from arc to intraplate volcanism as this rift- ing proceeded (Late Rifting stage). The arc fragment is surrounded by younger backarc ba- sins. The chemical composition of magmas in both the arc and backarc changed with time, but in opposite directions. In the arc, magmas be- came enriched in sialic components from the Early Arc to Early Rifting stages, whereas in the basins the magmas became more similar to mid-ocean ridge basalts (MORBs) with time. In southwest Fiji, the oldest backarc basin has subducted obliquely beneath the remnant arc du- ring the last 3 Ma, resulting in chemically ex- otic calcalkaline volcanism. During the last decade over 150 radiome- tric age measurements and 650 rock analyses, many with trace element and isotopic measure- ments, have been obtained for samples from Fi- ji, Tonga, and the surrounding seafloor (Figs. 1 and 2). These data are summarized, drawing from the publications of Colley and Hindle (1984), Gill et al. (1984), Hawkins and Melchi- or (1985), Kroencke (1984), Malahoff et al. (1984), Scholl et al. (1985) and Whelan et al. (1985), from the specific research papers refe- renced therein, and from the half dozen or so manuscripts currently in preparation by these people and others.

Jan 1, 1987

By E R. Ramanaidou

The presence of clays in channel iron deposits (CID) within the Pilbara region of Western Australia causes problems in the classification and subsequent processing of the iron ore. In particular, the presence of clay adversely affects the processing and ore metallurgical properties by increasing the amount of Si and Al. Iron ore companies are seeking new methods to quickly and objectively detect the type and amount of clay in these deposits. Traditional methods of clay quantification such as X-ray diffraction (XRD) and thermal analysis are time consuming and expensive. Reliance on bulk chemical techniques (eg X-ray fluorescence, (XRF)) to derive normative mineral abundances can give misleading results. For example, the replacement of Fe by Al in the structure of the iron oxide minerals, goethite and haematite, which dominate in CIDs, can be significant. Silicon can also occur in association with these Fe minerals. If not accounted for, chemical techniques may overestimate the normative abundance of clays. In comparison, reflectance spectroscopy in the visible-to-near infrared (VNIR) and short wave infrared (SWIR) wavelength range (eg 400 - 2500 nm) and Fourier transform infrared (FTIR) (6000 - 900 cm-1) analysis are non-destructive techniques that can provide rapid and objective mineralogical information. Both techniques are particularly suited to Al-, Fe- and Mg-OH bearing minerals such as clays. Kaolinite and, to a lesser extent, montmorillonite are the most common clay contaminants that occur in the Pilbara CIDs. Previous applications of VNIR-SWIR spectroscopy have demonstrated the potential of these methods in quantifying the clay mineralogy of CID ore. In this study, variations in the depth of diagnostic spectral adsorption features in the SWIR wavelength range of kaolinite and montmorillonite in standardised mixtures, with known proportions of clay, were well correlated to the abundance of kaolinite and montmorillonite, and to the clay alumina content (ie per cent Al2O3 û clay).

Jan 1, 2007

By H Fukaya T Miki, J Gamutan

Molybdenum disilicide (MoSi2) is a promising material for thermal applications due to its excellent heat and oxidation resistance. It can operate at temperatures of up to 1800°C as furnace heating elements and protect refractory metals such as molybdenum from rapidly reacting with air to form volatile molybdenum oxides at elevated temperature. In this work, the feasibility of forming MoSi2 on a molybdenum substrate by hot dipping in a silicon-saturated molten metal bath was investigated. This method is simple, predictable and can be used to coat large components and complex parts. It was found that tetragonal MoSi2 can be successfully synthesised on the surface of the substrate after dipping for 15 mins at 1000°C using molten tin (Sn), bismuth (Bi) and copper (Cu) baths. The growth of the MoSi2 layer was fast within the first 15 mins and then gradually slowed down with time. After dipping for 60 mins at 1000°C, the thickness of the MoSi2 layer were measured as 441.5, 19.5 and 13.1 μm for the copper, tin, and bismuth baths, respectively. The MoSi2 coating synthesised in this study provided oxidation resistance at 1150°C by forming a protective SiO2 layer on the surface. The SiO2 layer prevented the sample from rapidly oxidising by inhibiting direct contact between the molybdenum substrate and oxygen in the atmosphere. Compared to conventional methods, the proposed hot dipping method produces a MoSi2 layer more rapidly and at much lower operating temperatures. This makes it a more attractive option for coating large and complex components, with the potential to enable the use of MoSi2 in a wider range of applications.

Jun 19, 2024

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (- 30 + 6 mm particle size) and fines (- 6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Con- trol Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor struc- ture, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been exten- sively tested on both lump and fines on the shiploading conveyor at Damp- ier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encourag- ing. The principal advantage of IRONSCAN is that it provides rapid infor- mation on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to Implement. at the University of Melbourne, and those of us who were his students had learnt of the application of physical chemistry to pyrometallurgical processing, pioneered by Chipman in the USA, Wagner in Germany, and Richardson in the UK. It was possible, by applying this theoretical insight to the equilibria between metal, speiss or Legierung, matte and slag phases, to find a practical and effective way to recover metal values in some residues which had been accumulating for many years at the NA, but which had defied all attempts to treat them to that date. There was also an opportunity to study the batch lead refining methods still in use at all lead refineries apart from Port Pirie, and to devise optimis- ing techniques which greatly improved the operations and effected considerable savings. Next the writer spent some six years alternating between the BHAS, Port Pirie, and Imperial Smelting at Avonmouth in the UK, concerned with lead or lead-zinc smelting, and the develop- ment of several further continuous lead refining processes, before returning to Australia as Section Leader, Process Development in the CSIRO Division of Chemical Engineering, Fisherman's Bend, Victoria. Metallurgical opportunities which arose during this last period included the problem of tin smelting which had developed over about a decade: the world's tin smelters had been accustomed to treating fairly high grade tin concentrates, con- sisting of almost pure cassiterite, with very little impurity-mostly quartz, limestone, iron oxides, and sundry other silicates. Most such concentrates had been produced from alluvial deposits, where nature had already done some of difficult part of the mineral processor's work-at who knows what recovery-so that he could now produce high grade concentrates at high recovery. The smelters were not really set up for the treatment of lower grade concentrates, such as could be made with reasonably high recoveries from rock mining. Thus they imposed such penalties on impurities and lower than desired tin grades, that whenever a mineral processor improved tin recovery at the expense of lower- ing grade, such an improvement entailed a lower financial return to the miner. There was clearly a need for improved understand- ing of tin smelting, (at that time shrouded in secrecy) and develop- ment of techniques better suited to the treatment of lower grade concentrates. As well as the practical development, a start was made with the computer modelling of the smelting process, with the obiect of optimising the process parameters.

Jan 1, 1988

Segregation of granular material is a very common phenomenon. Realised in a forced manner it is a basis of all separation processes in mineral processing, mainly classification and beneficiation. Spontaneous segregation, occurring under dynamic conditions and making possible mutual translocations of grains, is however an undesired phenomenon as a rule. It decreases the degree of blending of the material which in many cases is an important technological feature of the material. It should be noted that the segregation can be treated as the reverse phenomenon to blending. The importance and frequency of spontaneous segregation has caused many rules and technical solutions to be developed aimed at decreasing the possibility of the spontaneous segregation. However, not enough attention has been focused on an quantitative description of the phenomenon of segregation, either to ways of quantitatively evaluating segregation effects or to explanation of the influence of conditions under which the grained material exists on the occurrence of segregation and its degree. The paper presents the following topics: 1. new numerical indicator for evaluation of the segregation degree (and blending) of material contained in an arbitrary determined region is proposed; it is determined relative to the maximum possible degree of segregation of the given material when taking into account its individual properties; values of the indicator can be calculated effectively for an arbitrary material, also for ulticomponent material. 2. there is proposed a way of evaluating the state of segregation (or blending) of material in an arbitrary part of the region mentioned above, based on investigation of the gradient of distribution of the material features; algorithms of analytical procedures and calculations are presented for typical cases met in mineral processing; 3. results of initial experimental studies, both laboratory and industrial, concerning the effect of the chosen factors occurring in transport and storage of the material on its degree of segregation are presented; and 4. conclusions referring to the fundamental and practical significance of the results are also presented.

Jan 1, 1993

By Hodkinson I, Slight M

Over the last five years Mt Leyshon has matured into a sizeable gold mine by Australian Standards. In the later part of 1990, after commissioning of the 3.5 mtpa CIP Plant upgrade, experience indicated there was potentially additional Mill capacity beyond that being utilised at the 3.5 mtpa rate. Overall throughput was limited by crushing plant performance and high operating costs resulting from the age and condition of the main crushing plant.In addition, mining was being carried out using a mining contractor who utilised relatively small, high cost mining equipment, and on-going exploration success was also indicating that the then current mine plan would result in only a portion of the available resource being exploited.

Jan 1, 1992

Mother Nature controls, technical professionals model and miners decide. Decisions to explore, mine and mill. Mine decisions, mine design, planning and scheduling are subject to the quality of models û geological models, geotechnical models, resource models, density models. The closer these models are to reality, the more accurate the predicted outcome. So why is it we delegate the modelling tasks to the most junior and least experienced people? If we insist on this, we need to support them û to provide them with æexperience acceleratorsÆ. Technical mentoring is the most effective way to provide the right information at the right time. When this information (read skills) is supplied at the right time we can inject experience into the quality of our modelling and into our decision- making processes. The objective of this paper is to share those behaviours and manners that foster relationships and create frameworks for skills and experience transfer. Central to this is an understanding of how adults learn, an understanding of the basic rules of mentoring etiquette, and the three keys to building meaningful mentoring relationships. An understanding of adult learning processes and styles provides a structure within which a mentor can understand the learnerÆs perspective. Understanding the world from the learnerÆs point is critical to selecting the right language to engage, teach and transfer skills. Basic rules of mentoring etiquette like timeliness, respect and trust need to be brought into the consciousness so they can be agreed on and monitored to prevent conflicts in cultural and generational norms between the mentor and the learner.Meaningful relationships hinge on the three behaviours: truly listening, rather than just hearing; understanding the technical issues within the WIIFM (whatÆs in it for me?) question; and facilitative behaviour. Stronger and more meaningful technical mentoring relationships within our industry will bridge the generational gap and ensure we can capture and capitalise on the wealth of grey hair experience and develop an informed group of young decision-makers.

Jan 1, 2006

Most new engineers in the mining industry do not realise the importance of legal obligations. During investigations the first question you are asked is: Do you have any proof or evidence? The smallest detail in an underground notebook or a diary entry is able to be used as your proof and/or evidence. The importance of a paper trail is often undervalued and overlooked when you first enter the industry. As a new engineer, all too often your legal obligations, including your duty of care are not given enough consideration. Whose job is it to inform you of what your legal obligations are and when do they end? Everyone has legal obligations at every level of the industry, from graduate to mine manager. The level of these responsibilities varies depending on the position that you hold. When you first start in the industry you need to understand what your responsibilities are and how you are expected to discharge them, whether they are memos, databases or senior sign-offs, etc. In order to fulfil your obligations you must first discharge your own obligation, which in turn discharges those of your department and ultimately those of the mine. As a graduate engineer in the mining industry what I have learnt about my own legal obligations has come directly from my own experience, which will form the basis of this paper.

Jan 1, 2007