Search Documents

By A F. Cooper

The northeast-southwest trending ~25 km2 area incorporating Bald Hill is located 18 km northeast of Haast, and 5 - 7 km west of the Alpine Fault in South Westland, New Zealand. The geology consists of Greenland Group greywacke overlain by a Cretaceous-Tertiary sedimentary sequence and fluvio-glacial/marine terrace deposits of Quaternary age. Alluvial gold in Cole Creek, draining west from the summit of Bald Hill, may be derived either from vein mineralisation in basement rocks or from fluvial or marine terraces.   This paper focuses on the potential for in situ gold and base-metal mineralisation in sporadic, siderite-rich quartz veins that cut basement greenschist facies metasediments that have been overprinted by contact metamorphism.   Throughout the area, vein compositions are dominated by quartz and commonly feature zoned plagioclase. Alteration adjacent to veining within the contact aureole is dominated by 1 - 2 mm, coarse grained biotite, with small amounts of sulphide, and is pervaded by abundant siderite veinlets. Outside the aureole, wall rock alteration to veins consists of fine grained chlorite. Trace element XRF analysis has been used to ascertain base metal concentrations within samples of vein and alteration zones collected from throughout the area. Vein and alteration zone mineral assemblages containing <5 per cent sulphide, with low concentrations of As, Cu, Pb and Zn indicate low potential for gold and base-metal mineralisation in the Bald Hill region. Contact metamorphism of Greenland Group basement in the northeast of the region, is likely due to emplacement of a poorly exposed Cr- and Ni- enriched gabbro. The presence of biotite and andalusite in hornfelses indicate contact metamorphism occurred at temperatures >350¦C and at depths <10 km. Widespread vein distribution does not appear to be related to contact metamorphism or gabbro emplacement. Further research is required in order to establish the fluid source from which the veins were precipitated.

Jan 1, 2007

By S Paciornik, G Schinazi, M H. de Pinho Maur-cio, M B. Vieira, O da Fonseca Martins Gomes, D T. Wagner

Vale (previously CVRD û Companhia Vale do Rio Doce) evaluates the microstructure of sinters in order to understand their characteristics and behaviour in the agglomeration process, and the correlation with conventional quality parameters. Efforts on image analysis development are in progress between Vale and PUC-Rio in order to improve both the qualitative and quantitative evaluation of a representative portion of material. In the present work, digital microscopy techniques were developed allowing this kind of assessment. Employing a motorised and computer controlled optical microscope, low magnification mosaic images covering complete sinter samples were automatically obtained. The mosaics provide a powerful qualitative overview of the whole sample while allowing low resolution quantitative evaluation of the major phases. In addition, quantitative results for phase fractions were compared for the same sample regions at three magnifications (5x, 10x and 20x objective lenses). A single field (1 x 1) at the lowest magnification corresponds to mosaics of 2 x 2 and 4 x 4 images at the higher magnifications. The automated system allows perfect registration between the mosaics and the single image. Changes in phase discrimination were evaluated as a function of optical resolution, and phase fractions obtained by interactive segmentation of the image histograms were compared. While finer dark phases, eg silicates, were only visible with the best optical resolution, coarser phases such as haematite and pores were measured at all resolutions. For haematite, magnetite, ferrite and pores, the largest relative error in area fraction, between the images obtained with the 5x and 20x lenses, was 12 per cent. The results for silicate were less accurate with a relative error of 44 per cent. The results indicate that digital microscopy provides a flexible method for qualitative and quantitative evaluation of these materials.

Jan 1, 2008

By E U. Petersen, D R. Cooke

Hydrogen and oxygen isotopic constraints on hydrothermal fluid composition from the Pliocene Boyongan and Bayugo porphyry copper-gold deposits (southern Philippines ) reveal mixing of magmatic and sea water reservoirs as the hydrothermal system evolved. Magmatic-equilibrated fluids (d18O: +8.3ë to +9.1ë; dD: -61ë to -51ë) are represented by hypersaline brines implicated in copper-gold transport and deposition. These dominate the fluid inclusion assemblage in early comb-quartz (unidirectional solidification textures), miarolitic quartz, and in K-silicate-stage quartz-K-feldspar ¦ biotite veins. Fluids responsible for post-K-silicate alteration assemblages of pyrite-clay (illite, pyrophyllite and kaolinite), alunite and smectite are represented by low-moderate salinity two-phase inclusions in co-existing quartz. These are interpreted as mixtures of evolved magmatic fluids (d18O dD: -42ë to -20ë) with evolved Pliocene sea water (d18O: + 4.0ë; dD: +4ë). The isotopic evidence for sea water involvement in the hydrothermal system suggests that porphyry emplacement and associated diatreme formation could have occurred in a submarine setting. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By V S. T Ciminelli

This work aimed at evaluating the acid rock drainage (ARD) potential of five samples of a Brazilian gold sulfide mine in a decommissioning process. Three of the most traditional ARD prediction techniques, Standard Acid Base Accounting (Std ABA), Modified Acid Base Accounting (Modified ABA), as static methods, and humidity cells as a kinetic method were tested. Both the Std ABA and the Modified ABA results indicated an acid generation potential for some of the studied samples. In the other cases the results were inconclusive. The five samples were then submitted to humidity cell tests during 27 to 30 weeks. At the end of the period, the leachate pH was stabilised in a range from 3.4 - 4.1 (four samples) to 5 (one sample). The presence of relatively high levels of sulfate and dissolved metals was detected throughout the operation, specifically, Ni and Zn, and less frequently, As. These findings are discussed with the help of the samples mineralogy and Eh-pH diagrams. The results obtained in this investigation indicated potential environmental risks of this mining area. In this particular case, the kinetic tests were shown to be essential to the identification of the samples ARD potential.

Jan 1, 2003

By A Gerdes, H BrStz, E GSbler, D Davis, F Henjes-Kunst, S Dewaele, T Graupner, T Oberthnr, M Sitnikova

Following the United Nations initiative to fingerprint the origin of conflict materials, the German Federal Ministry for Economic Cooperation and Development has decided to fund a pilot study on coltan ores. Since 2006, our working group has been investigating columbite- tantalite (coltan) mineralisation, especially in Africa, also within the wider framework of establishing certified trade chains. More than 300 samples were obtained from the worldÆs major coltan producing areas. Special attention is, however, directed to samples and concentrates from Ta-Nb-Sn provinces in Africa: Democratic Republic of the Congo, Rwanda, Mozambique, Ethiopia and Namibia. Using state of the art analytical tools, we investigate mineralogical and chemical parameters obtained from columbite-tantalite ores and concentrates in order to distinguish between ore provinces, likely even down to the deposit scale. Methods employed include fully automated electron microscopy (mineral liberation analysis), electron microprobe analysis (major and minor elements), laser ablation plasma-source mass spectrometry (trace elements and U-Pb dating), X-ray fluorescence spectroscopy (bulk major and trace elements), X-ray diffraction analysis (mineralogy and structure) and thermal-ionisation mass-spectrometry (U-Pb dating). Major and trace element concentration patterns, mineral assemblages in the ore concentrates, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Furthermore, the following age populations are evident:Archaean (>2.6 Ga);Palaeoproterozoic (1.9 - 2.1 Ga);early Neoproterozoic (æKibaranÆ; 0.98 - 0.93 Ga); andlate Neoproterozoic to early Palaeozoic (ca 0.5 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale. Our preliminary analytical results indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible.

Jan 1, 2008

The Bowen Basin of Central Queensland covers a total area of 3 200 000 ha. The Basin has proven reserves of about 24 000 000 tonnes of coking coal and steaming coal which constitutes about 70 percent of the known coal reserves in Queensland. Large scale open cut coal mining in the Bowen Basin commenced at Moura in 1959. There are now 16 open cut mines operating in the Basin and they collectively mine through about 3000 ha of land each year. Most of the land which has been mined has previously been used for extensive grazing. No mining has yet taken place on cropping land although coal reserves underlie land which has been cropped or has potential for cropping. The primary objectives of almost all of the mining companies operating in the Bowen Basin are to rehabilitate mined land to a stable and productive form which is compatible with surrounding land use which is dominantly grazing. The acceptability of these objectives is considered against the prospect of mining of cropping land and the qualified success of the return of rehabilitated land to grazing uses.

Jan 1, 1987

Comprehensive occupational health and safety legislation in Australia is comparatively recent. It follows the examples set in U.S.A. and U.K. a decade or more ago. In Western Australia the Occupational Health, Safety and Welfare Act was proclaimed in April 1985. It still has a long way to go before it achieves all its objectives. The mining industry has developed a substantial body of health and safety regulations under the Mines Regulation Act. Considerable practical expertise in such matters already exists, much of it developed from hard won experience. As a result it would prefer not to become engulfed in the new legislation. It would prefer to build upon the cooperatively developed policies and workable practices in the field of occupational health and safety with which it is familiar. Associated Minerals Consolidated Ltd. is a leading mineral sands producer in Western Australia and has continuously developed its occupational health and safety policy and practices. Under the banner of "Resource Control", AMC seeks to provide a safe and healthy working environment at all times. This is being achieved through a strategy of a policy, a defined organisational structure and a detailed programme, which together comprise the "Resource Control System". Some of the activities and achievements of AMC in the field of occupational health and safety are compared with the objectives of contemporary legislation, and details of some of the specialised areas of the Resource Control Programme are discussed. The paper will also highlight and discuss impractical areas of potential legislation.

Jan 1, 1986

Airblast overpressure legislative limits can be extremely difficult to meet throughout Australia, which has by far the most stringent limits of any nation in the world. As the difficulty in meeting the limits is strongly dependent on the scale of mining, it is not surprising that the Australian coal mining industry is experiencing particular difficulties in meeting these limits. Eight full scale overburden blasts have been modelled with respect to overpressure impact for a strip coal mine, involving both dragline (cast) blasting and pre-strip (non-cast) blasting. Overpressure levels in the range 100 to 125 dBL have been measured at distances varying from 2.4 to 5.7 km, and modelling has successfully estimated both the amplitude and shape of overpressure waveforms to within an average of 1.2 dBL. Typical errors of prediction are around 0.6 dBL. This accuracy of prediction has been achieved by considering the impact of only the face holes, and the accuracy of prediction of both shape and amplitude suggests that it is these holes which dominate the environmental overpressure impact at distances in the range two to six kilometres, for cast and pre-strip blasting operations. Modelling has been based upon the Elemental Overpressure Wavelet proposed by Richards and Moore (2002), incorporating actual hole coordinates, actual delay timing, and assumed delay scatter statistics. The incorporation of delay scatter statistics has been particularly significant, and allows the determination of the range over which the peak overpressure levels are expected to vary. To date, modelling has considered only the use of conventional pyrotechnic delays, though simple adjustment to the scatter definition would allow estimation of overpressure levels, and their variability, with electronic delays.

Jan 1, 2004

By Worner H. K

The paper briefly summarises the work of the Titanium Research Section in the Metallurgy Department of the University of Melbourne and mentions the development of a new electrolytic process for titanium production. This process utilises the "hot-spot" cathode technique and titanium carbide anodes. An introduction is given to three further papers on titanium metallurgy to be presented to the Institute.INTRODUCTIONThe unique combination of strength, lightness and corrosion resistance possessed :by titanium and its, alloy has made them of great interest to engineers. However, high cost, difficulties of production and limited knowledge of techniques of application restrict their usage at present almost exclusively to high priority armaments.The cost of the metal is divided between extraction and processing and much research has been carried out to devise new and cheaper methods for winning the metal from its ores. Processing costs will be reduced when production volume increases.Extraction research is proceeding rapidly overseas and Kellogg (1955, p. 72) reports that 'at least seventeen companies in the U.S.A. are interested in titanium production. Of these, two are producing the metal by a modified Kroll process, three are building Kroll plants and the remainder are in various stages of research activity. The Horizons Corporation alone is contemplating electrolytic extraction and is building a pilot plant. Steinberg et aI. (1955, p. 252, p. 332) have reported the early work done by the HorizonsCorporation on electrolysis of potassium fluotitanate and titanium monoxide in fused salt electrolytes. Of these two, the former appears to be the more attractive process.

Jan 1, 1956

By A Goldstone, M Fitzpatrick

Contemporary mine wastewater flows are subject to stringent water quality standards before discharge to local waterways. Strict criteria are often applied as a result of fears of extensive acid mine drainage; a feature of the many abandoned mine adits around the Coromandel, Central Otago, and the West Coast. In most cases the USEPA water quality criteria have been used to set treated wastewater discharge water quality standards. In future it is possible that the recently published ANZECC water quality criteria guidelines will be used for this purpose. The ANZECC guidelines also provide for the establishment of discharge criteria at specific sites, rather than accept the trigger values. The use of site-specific criteria for treated wastewater mine discharges was pioneered at the Golden Cross gold mine, near Waihi, in the late 1980s. The procedure used to derive water quality criteria was based on USEPA guidelines. In developing the Golden Cross criteria, only species that occur, or are similar to those that occur in the Waitekauri River were used. The mine commenced discharge of treated wastewater in 1991, and macroinvertebrate communities in the vicinity of the discharge point have been regularly monitored twice a year for the past 12 years. Despite fluctuations in community composition and abundance over that period, no permanent significant changes in the macroinvertebrate communities occurred between sites above and below the treated wastewater discharge. The success of the site-specific criteria at Golden Cross has shown how the application of this methodology can result in the protection of aquatic life while allowing for the discharge of treated mine wastewater.

Jan 1, 2003

By C B. Valentin

It is acknowledged that the analysis of iron ores using X-ray fluorescence (XRF) for major and minor elements is best carried out on fusion discs. This method of sample preparation eliminates mineral and particle size effects which can lead to biased results when using pressed powder pellets. However, the fusion disc method is costly as it requires a high capital investment in platinumware, requires experienced operators and uses expensive fluxes. Also, the dilution effect complicates the analysis of trace elements. For many applications, such as exploration and mining control, the method of XRF analysis of iron ores by pressed powder pellet probably provides data of adequate quality. Kumba Iron Ore, an iron ore producer in South Africa, recognises this and carries out most analyses of iron ore by pressed powder pellet and uses the automated fusion method mainly for certification of in-house calibration standards and quality control (QC) samples that are used for validation of pressed powder pellet method purposes. Automated fusion is also used for analysing the composite export shipping samples. All the other exploration, production, despatching and plant operation samples are done by the pressed powder pellet method. Automation of sample preparation procedures should improve the quality of data for pressed powder pellets. To compare the precision of the three methods of sample preparation and XRF analysis, 20 aliquots of a QC standard were prepared and analysed by each procedure/preparation method. The results and statistical data on the most important elements, Fe, K2O and P, are as shown later in Table 2.Clearly the precision is best for the auto prepared fusion discs, as expected, and worst for the manually prepared pressed powder pellets. However, the data generated from the auto prepared pressed powder pellets compare remarkably well against those from the auto prepared fusion discs.

Jan 1, 2007

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By Ryan CG, Ramsden AR, Sie SH, French DH, Griffin WL

Proton microprobe and electron microprobe analysis are being used in combination for in situ determination of the trace element contents of oxide, sulphide and silicate minerals in a sample of the Merensky Reef. Initial results indicate that chromites contain only Ni, Zn, Ga, Zr ar d Nb. Platinum-group elements, if present, are at concentrations less than 2 to 6ppm. Ru, Rh and Pd are the only platinum group elements to be consistently detected in the sulphides. PentLindite is the most important host for these elements with the concentration of these elements being dependant upon the mineral association in which it occurs

Jan 1, 1989

By Ibrahim AR

The experimental phosphate mine of abu Tartur has been recently placed into production. Some problems'have been encountered in maintai- ning grade control due to the differences between early block estimates and actual produ- ction grade. An area of 100 km2 is evaluated by using four methods of evaluation , namely polygonal, inverse distance , inverse distance squared and geostatistical methods. The results of calculations are compared statistically with the control values of grade and thickness. The comparison showed that the. kriging technique gave better estimations for the relative ore reserved, while for grades or thickness any of these techniques except the polygonal can be Used.

Jan 1, 1986

By Mogi G, Akaike A, Yamaguchi U

A new algorithm has been investigated for three-dimensional open pit designs to improve the dynamic cone approach which utilises the dynamic programming technique. The conventional dynamic cone method was improved by introducing examination processes: 1. whether any negative blocks are included in a unit cone or not; and 2. whether it is possible or not to leave the negative blocks unmined in the unit cone without disturbing the geometric condition imposed on the slope angle of the cone. The newly developed algorithm was applied to a large-scale open pit copper mine in a planning stage and the results have been compared with those obtained by the conventional methods.

Jan 1, 1995

By Windsor C. R, Thompson A, Bywater S

A new high tensile strength, steel cable, that may be grouted into boreholes has been developed for use as rode reinforcement. The manufacturing technique produces a birdcage pattern in which the cross section varies along the length of the cable. The load transfer from cement grouts to birdcage cables has been demonstrated in laboratory tests to be better than that of standard 15.2 mm diameter seven wire cables. The manufacturing process also allows for a wide range of capacities which may be specified by design engineers. The various birdcage cable configurations have been applied as rock reinforcement in a number of Australian underground and surface mines.

Jan 1, 1990

This report on the 5th International Conference on Underground Space and Earth Sheltered Structures, which was held at the University of Technology, Delft, the Netherlands, on 2 to 5 August 1992, was submitted to the members of the Australian Underground Construction and Tunnelling Association. The report describes the conference themes and outcomes and puts forward some observations about a growing world-wide interest in the promotion of appropriate uses of underground space. The report recommends the creation of an Australian centre for research to bring together a wide range of professional disciplines and to focus attention on the potential benefits of using underground space.

Jan 1, 1993

By Shibata Y, Shimizu R, Fukushima A

Kobe is divided by the Rokko Mountains, runn- ing from east to west. The southern section of Kobe is highly developed in contrast with the northern section, but big, new residential pro- jects like the Hokusetsu New Town and Hokushin New Town are steadily being developed. To handle future traffic between the two sections of the city, the double-tracked Hokushin Line, now under construction, will connect the Shin Kobe Station of the Kobe Municipal Transit (Kobe's subway system) to the Tanigami Station of the Kobe Electric Railway. The locations of Kobe city and Hokushin Line are shown in Fig.-1 and Fig.-2 respectively.

Jan 1, 1987

By T Iwadachi, T Fujisawa an, G R. Alvear

A large amount of Be2C and BeO is formed during the Cu-Be alloy production process, because beryllium is a highly reactive element. Carbide and oxide formation impairs the production yield and the quality of the Cu-Be alloy products, and therefore should be minimised. As a first step for solving these problems in the process, the following thermodynamic properties of the Cu-Be-C-O system were investigated. Based on the results, the equilibrium relations of the Cu-Be-C-O system were clarified and the operational conditions of the current Cu-Be alloy production process were also examined and discussed.

Jan 1, 2000