Search Documents

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

TasmaniaÆs mineral endowment has resulted in 600 abandoned mines. Commonly occurring sulfide minerals such as pyrite and pyrrhotite can generate acid drainage and also mobilise heavy metals. Due to the StateÆs steep topography and high rainfall the risk to water quality in the receiving environments is significant. Surface waters impacted by abandoned mine sites typically showed high sulfate and metal distribution at pH range of 2.0 to 5.0. The impacted waters generally showed metal distribution in the high acid/extreme metal to low acid/low metal range. A similar trend was shown by sulfate distribution. Elevated levels of metals and sulfate downstream from several abandoned mine sites indicated that active sulfide oxidation is occurring and these sites may be potential point sources of metal pollution in the receiving environment. High correlation between metal and sulfate distribution suggests that sulfate distribution in surface waters may be used as a cost-effective investigation tool for preliminary assessment of acid drainage.

Jan 1, 2003

By Ellis WK, Greenwood-Smith R

A nuclear technique for the analysis of copper in bulk materials has been developed and successfully field tested at Mount Isa Mines Limited. The technique utilises the gamma-ray resonance scattering process. A bulk analyser based on this technique gives a rapid and accurate measurement of the percentage by weight of copper or nickel aver- aged over a large mass of sample, typically 20 kg. The only sample preparation required for accurate analysis is crushing to -2.5 cm. At Mount Isa over 100 mineral samples covering a wide range of rock types and copper contents were analysed. Bulk analyser assays and chemical laboratory assays agreed closely for underground pillar-extraction and geolog- ical chip samples, conveyor belt samples, and finely ground samples from the ore concentrator. For the concentrator samples, the root mean square deviation between bulk analyser and chem- ical laboratory assays was 0.06 wt.% copper. The chemical assay errors for these samples were about 0.06 wt.%

Jan 1, 1975

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

By Towsey C. A

Significant advances in regional geochemical exploration techniques have been made over the last 5 years in the search for gold deposits. This has occurred largely by the development of the bulk cyanide ex- tractable gold (BLEG) also known as the Bulk Cyanide Leach (BCL) tech- nique. The technique has been developed and designed for Australian conditions and has two main ad- vantages over the pan concentrate technique preferred by many ex- plorationalists, viz:,. 1. It is designed to collect ultra fine gold common to epithermal and other north Queensland types of gold deposits. 2. The large sample (approx.5 kg) allows very low detection levels, ranging between 0.1 and 0.05 ppb Au. The use of the BLEG technique in exploration has led to the discovery of the Wirralie gold deposit and numerous other epithermal gold prospects previously undetected by pan concentrate and minus 80 mesh (pathfinder elements) surveys in the Drummond Basin.

Jan 1, 1989

By S B. Martin, M P. Simpson, J L. Mauk

The Martha deposit in Waihi, New Zealand, is a giant adularia-sericite epithermal gold-silver deposit that formed 6.0 to 6.1 Ma, and has produced over 6.4 Moz gold and 39.9 Moz. Fluid inclusion analyses were undertaken on a limited number of vein samples from Martha. The results from this eight week student project are preliminary but agree with previous studies. There is little variation between primary and secondary inclusions and between different vein types, except that homogenisation temperatures of the inclusions in sphalerite grains are on average 20¦ to 30¦C higher than the average quartz vein values. Overall the temperatures of homogenisation ranged from 182¦ to 258¦C and final ice melting temperatures ranged from 0.0¦ to 2.8¦C. Unusual black inclusions were also found associated only with the ginguro bands. Some of these appear to be solid sulphide inclusions but others are not so clear.

Jan 1, 2007

The Western Australian Mining and Petroleum Research Institute (WAMPRI) was established in 1981 by the Western Australian Government as a funding and co-ordinating Institute to foster research into the mining and petroleum industry within this State. To June 1984, the Institute has sponsored 34 projects with a total notional value of $2.5 million and an actual cash commitment of $1.5 million. Strong support for WAMPRI has come from Industry with 60 companies contributing half the money needed for the research grants.The 34 WAMPRI projects funded so far cover all aspects of the mining and petroleum geosciences.Several WAMPRI projects are concerned with gold including processing technology and the development of exploration models and techniques, they are providing successful results.Although well supported by Industry there is a surprising lack of applications being submitted to the Institute in the area of mining engineering, where it is felt there is much scope for research projects.

Jan 1, 1984

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

By Eisele TC

Horizontal perforated-plate baffles were shown to improve the cleaning efficiency of a flotation column when processing coal from two sources. The baffles consisted of flat plates with holes large enough to avoid plugging problems, and they improved the washing efficiency by making the flow patterns in the column closely approach plug flow. Tests with varying amounts of baffle open area showed that the optimum was between 30 and 40 per cent open area, which effectively prevented backmixing without seriously reducing capacity. The baffled column had previously been tested under ideal conditions with good results (87 per cent pyrite rejection at 85 per cent combustiles recovery), and so the tests reported here were intentionally run with difficult-to-float coals to determine the benefits of baffling under adverse conditions. For an original coal feed containing 38 per cent ash and 3.23 per cent total sulphur, the baffled column could recover 84 per cent of the combustibles while rejecting 84 per cent of the ash and approximately 54 per cent of the pyritic sulphur. Without baffles, the column recovered 88 per cent of the combustibles while rejecting only 76 per cent of the ash and 45 per cent of the pyritic sulphur. Subsequent tests with a dye tracer showed that the baffles reduced entrainment by approximately a factor of five, while the recovery was reduced by only a few per cent. Overall, the loss of capacity due to the baffles was more than offset by the improvement in product quality.

Jan 1, 1993

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

The Fosterville Goldmine in Victoria employs bacterial oxidation (BIOX« Process) to liberate gold from its flotation concentrate. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation even with fine grinding. Once liberated by the oxidation process, the gold is then available for cyanide leaching. While the oxidation process is very effective, it has been found that a portion of the liberated gold can become suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. This paper discusses investigations into the causes of the loss and also describes the successful use of quebracho tannin in reducing colloidal gold loss. Laboratory and subsequent plant trials, showed a gain of 2.6 per cent in overall gold recovery based on mill feed and waste stream data.

Jan 1, 2009

A statistical investigation of folding at Mount Isa disclosed similar patterns in both the shales and the "silica dolomite" zones. Analysis of these patterns yields 3 groups of folds fully developed north plunging folds, fully developed south plunging folds, and flexuresrepresenting stages of development of folds. Interpretation of results indicates that a regional force from a southerly direction was responsible for the folding.The general pattern of shearing is allied to that of folding, with the exception of bedding-plane shearing. Many shears resulted from continued application of force on folds which ruptured after overthrusting. Other shears resulted from rupture of the more incompetent shale members, without associated folding. The shear pattern is consistent with the theory of a regional force from a southerly direction.INTRODUCTIONThe notes on folding and shearing presented in this paper are part of a current study of the structural geology of Mount Isa.FOLDING 1Measurement of FoldsInvestigation of folding underground involved the measurement of plunge, strike and dip of the axial plane, and the order of magnitude of each fold, together with its location and the rock type. The total number of folds measured was 701, of which 411 occurred in shale areas and 290 within the "silica dolomite" zones. All folds measured are located on main levels, from 7 level to 13 level inclusive. The sections of the mine involved are the Black Star, Black Rock and Racecourse. Detailed investigation of folds on the upper levels (4, 5 and 6) has not yet been done, but observations there suggest...

Jan 1, 1961

In the last two decades, equipment used in the coal mining operations has become much more sophisticated. The way that work is organised and performed in the industry has also changed significantly. Changes in equipment specification or procedures inevitably means that the risk associated with that equipment or procedure also changes. In an attempt to address this the Joint Coal Board Occupational Health and Safety Trust (JCB) commissioned the University of New South Wales Mining Research Centre and Mine Site Technologies to perform a feasibility study into the development and deployment of Virtual Reality (VR) based training simulators in the New South Wales coal industry. The main aims of the study were to identify, the key providers of VR Technology, the VR options available to the JCB and the information that would need to be included in any simulator. It was anticipated that a critical assessment of these components would produce a format for a cost effective, state of the art simulator that could be readily accessed by all mines. The expectations of the feasibility study were that VR should offer three-dimensional (3D) simulations that are interactive, high-resolution models of real environments based on best practice Safety Management Plans. It was anticipated that the simulations would allow trainees to experience the consequences of poor decision-making and allow them to learn from their mistakes in a safe and forgiving environment. It was envisaged that such simulators would become an addition to the existing training methods used in the industry.

Jan 1, 2003

Over the last 15 years the contract mining concept has developed into an integral part of the Australian mining industry. Today it is a $2 billion per annum industry with the potential to continue to grow at a rate of between ten and 20 per cent. Australian contract miners have also exported the concept overseas where growth prospects are unlimited. The industry today is at a cross-road where both contractors and mine owners must consider the current state of the contract mining industry and where it is heading. To look at the present and the future, it is necessary to look back at the history of contract mining and why it has developed. Current industry concerns can then be summarised and the areas that need to be considered to enable the industry to prosper, reviewed. The ultimate goal is to reach solutions with benefits to both the mining companies and the contractors.

Jan 1, 1996

By Yamakita T, Yoneoka Y

The Chigirishima Smelter of Toho,Zinc Co., Ltd. is the largest independent custom lead smelter in Japan and produces about 60,000 tonnes/yr of electrolytic lead. The quantity of slag produced by blast furnace is approximately 65,000 tonnes/yr, 30,000 tonnes/yr of which is sent back to the sintering plant for mixing with lead concentrates. The remaining slag used to be piled up at the yard until the operation of the fuming plant started in July 1977. We examined the slag fuming process with the purpose of achieving: 1) Improvement of the operating results by recovering zinc and lead from blast furnace slag. The lead content in slag at Chigirishima is slightly high, because the height of blast furnace shaft is low and consequently the quantity of sinter smelted per area at tuyere level is rather large. 2) Production of a salable slag as raw material for cement by lowering zinc and lead content in slag.

Jan 1, 1980

The treatment of the Broken Hill ores has,undergone many changes during the last ten years, and it may be of interest to some of the members to know what are the main lines on which the Proprietary Mine works at present. It must be understood that the want of absolute uniformity in the treatment amongst the various mines at the Barrier does not prove that some of the mines are working on wrong lines, for the ore is not exactly the same along the whole line of lode; this necessitates a variation in treatment, although generally only in detail.At the Proprietary Mine the ore is all mined by contract the miners are paid so much per ton for clean ore. The ore in the mine in most stopes is mixed with gangue, and the inclination of the uliners is, of course, to mix gangue with the ore, so as to be paid for as large 3 tonnage as possible. This is quite natural clean ore is easily distinguishable from clean gangue, but most lumps are a mixture of clean ore and gangue in varying proportions. The miner will naturally throw into his heap pieces which he considers still good enough, whilst the management may consider these pieces just a trifle too poor; consequently a check must be kept on this.This necessitates the first operation to which the ore is submitted. 'The trucks tare 51 cwt.; average load 21 cwt.), as they are loaded underground, have a ticket attached::showing to whiyh contract they belong on arrival at the top of the shaft they are passed over a weigh bridge...

Jan 1, 1907

By A McRae

Much of western New South Wales is characterised by an extensive regolith formed during more than 60 million years of exposure, weathering and erosion. This cover includes intensely weathered in situ regolith and superimposed transported materials of variable thickness, commonly in complex palaeochannel systems. Mineral exploration in this region has been considerably hampered by the cover, which can complicate or maskgeochemical anomalies and also obscure geophysical signatures. A detailed multi-disciplinary study of part of this region, centred on the Cobar-Girilambone area has demonstrated a methodology for exploring through this regolith. The approach involves regolith-landform mapping to establish the main landscape and palaeolandscape elements and to determine the nature and spatial occurrence of different regolith materials. By combining knowledge of the surface distribution of different regolith-landform units with available 3D information on the regolith and geophysical data it is possible to construct simplified derivative maps or exploration ægoÆ maps, which can be used to advise appropriate exploration strategies or help interpret acquired exploration data. This study has also established the major regolith controls on geochemical dispersion and determined key background element associations. These regolith-related element associations can result in highly variable background levels for many trace elements and need to be understood and factored into the analysis of geochemical data for different regolith sampling media. With better knowledge of the regolith it is possible to select the most appropriate exploration techniques and sampling media for a given area, as well as apply appropriate normalisation procedures to the acquired data. Exploration success can be greatly improved by using many existing techniques in æregolith smartÆways.

Jan 1, 2004

On the 18th November, 19'58, the first coal was delivered to the Morwell Power Station from the adjacent Open Cut using conveyors for the transport of the coal from the working face to the boiler bunkers. As the cut develops the coal seam will be worked for its full depth of about 360 feet from four benches, each feeding a conveyor line along th.e face and up out of the cut to the power station and briquette factory. By 1970 the estimated maximum daily demand reaches 60,000 tons and the total annual output 18 million tons. The complete conveyor installation will then total some 9 miles with a capital cost of over £3~ million.The choice of conveyors in place of the more usual rail system was made possible by the development of movable belt conveyors which use mechanical conveyor shifting, high belt speeds and flexible high strength belts and the paper deals with these and some other aspects of the scheme.INTRODUCTIONThe development of brown coal deposits is usually based on open cut workings equipped with a few large dredgers giving an almost continuous output of coal or overburden which has to be hauled a comparatively short distance. These are ideal conditions for conveyor operation, and it is surprising that, until recently, rail transport has been used almost exclusively in brown coal open cuts. In some cases inclined conveyors have been introduced to take the coal from the coal levels up out of the cut to bunkers at groundlevel, but trains have been left to operate between the ditch bunker feeding the conveyor system and the dredger.

Jan 1, 1960

The purpose of this paper is to present a detailed account of the development of the Blasthole Diamond Drilling method of stoping now used at the property of Big Bell Mines Limited, in Western Australia.The ore body is one of the large low grade gold deposits of this State, being a continuous lens 1,850 ft. long and ranging in width from 15 ft. at the ends to 120 ft. at the widest part, the average width being 59 ft. It was first worked in 1913 by a local syndicate, and up to 1924, when operations ceased, 64,448 tons of 3.4 dwt. ore were mined from a shallow open cut. Between 1928 and 1932, 15 deep diamond drill holes were put down to test the ore body at vertical depths ranging from 100 to 700 ft. On the information gained from these drill holes, Premier Gold Mining Co. Ltd. began underground explQration. A level was driven at a depth of 253 ft. and crosscuts put out to the full width of the, orebody at intervals of 100 ft. along the strike, all ore broken being put through a sampling plant. On completion of this sampling,' Big Bell Mines Limited was formed as the operating company, and a plant with a capacity of 1,000 long tons per day was erected and mining and milling operations were commenced in 1937. Ore was first mined from glory hole stopes, 65 ft. long, separated by 35 ft. pillars, by benching using conventional steel with changes up to 20 ft., all broken ore being hauled to the main shaft on the...

Jan 1, 1948