Search Documents

By J P. Moodie

Recent trends in flotation technology are briefly reviewed. These show that considerable development has been made as the operators, suppliers and technologists have responded to the challenges of the industry. Most of these advances have been based on empirical and phenomenological methods. There is a considerable opportunity to make further advances through a more fundamental, scientific approach. Some of this work is discussed and, although progress is being made on this front, industrial uptake has been somewhat slow. A number of specific issues facing the industry are discussed.

Jan 1, 2005

Both safety and productivity in underground gassy coal mines can be improved substantially if an appropriate gas management system is introduced. A strong direct relationship exists between the gas emission rate, roof and floor strata relaxation zones characteristic, mining activities and gas drainage practices. Detailed knowledge of geological factors, gas and coal-rock properties, as well as mining systems are necessary for the methodology used in predicting overall underground gassiness, and planning gas capture and ventilation systems. Early gas emission calculations for various mining activities, particularly for the longwall mining system are essential. A reasonably accurate prediction of gas make as well as the design of ventilation, gas recovery (drainage holes) techniques can be made using 'Floorgas' and 'Roofgas' computer simulations, provided sufficient geological, mining, and gas data are made available.

Jan 1, 1998

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Williams ID

Ore and coke of various size fractions (1 to 11 mm) were packed in a column (146 ó) and resistance to air flow measured under a range of conditions. Results have shown that layered charging results in an interface having essentially a directional structure the thickness of which is directly proportional to the coke and ore size ratio and whose flow resistance exceeds that of the coke layer many times its thickness. Friction factor - Reynolds number plots showed large positive departure from the Ergun equation for all components investigated whilst functional analysis and that in terms of bed constants, showed a strong dependency of the pressure gradient on bed properties and the actual particle size as well as the size ratio. It is also shown that pressure gradient in mixed beds follows previously reported behaviour and that a directional interface offers higher resistance to flow than a mixed interface having the same volumetric ore/coke ratio. Significance of results to practice is discussed.

Jan 1, 1975

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By Khosia NK, Ravishankar SA, Sankar TAP

Alumina reduction in Rajhara iron ore slimes essentially involves separation of hematite from gibbsite in relatively coarser fraction and from kaolinite in the finer fraction. Selective dispersion flocculation studies on synthetic mixtures clearly indicated that while it was possible to achieve almost perfect separation of hematite from kaolinite using starch and PAMX (modified polyacrylamide containing hydroxamate functional groups) flocculants, no selectivity was observed in iron oxide-alumina system. A schematic flowsheet suggested on the basis of this work for the beneficiation of Indian ore slimes thus consists of classification in a hydrocyclone, followed by selective dispersion of coarse fraction (underflow) and selective flocculation of the overflow fraction. Starting with a feed assaying 46 per cent Fe and 11.6 per cent A1203, a concentrate assaying 60 per cent Fe and 4.7 per cent A1203 could be produced at an overall iron recovery of 60 per cent using conventional Reagents.

Jan 1, 1993

By Davison GR

The cost of drilling consumables is always a large component of any mine budget. It is important that this cost be carefully examined with a view to reducing the overall cost per inetre or at least minimising its escalation.At Renison it is considered that the only way to ensure drilling costs do not rise unduly is through a total system of control from purchase to disposal.In 1979 extension of an existing drill supply service contract was carefully examined and abandoned in favour of a hybrid system. This system is providing a great deal of control over the use of drilling consumables and has maintained a relatively constant cost per drilled metre over the last five years.Current consignment stock contracts for drilling consumables are strictly specified by the Technical Services section of the Mine Department and consumables purchased under these contracts are distributed and refurbished/sharpened by a contractor.The total result of this package is individual drilling items that achieve the best cost per metre and careful distribution and maintenance to ensure maximum life.

Jan 1, 1985

By Ya Vladimirov D, Yu Khudin M, Kiebanov A. F

Problems of the creation of an automated cartographic system for environmental condition estimation and forecasting in mining region are discussed in this paper. The Geographic Information System (GIS) ARC/INFO is offered as the platform for such a system. A breadboard model of the system was tested on the example of Kemerovo province (Kuznetsk coal basin), the most ecologically impacted mining region of Russia. As a result parameters of territorial distribution of integrated adverse environmental impact of the industrial enterprises are reviewed. Administrative regions of Kemerovo province were rated according to a degree of environmental pollution. Further, specific weight of various industries in pollution of region is determined.

Jan 1, 1995

By S Corbel, P J. T Donchak, W Gorczyk

The Hodgkinson Province numerical modelling project aims to develop an improved understanding of the physical conditions that lead to the localisation of goldbearing fluids within known systems and apply this understanding to the prediction of potential new sites of gold mineralisation. The project follows a series of stages from identifying the key parameters required to construct and test simulations through to reverse engineering of known deposits and ultimately applying the conditions identified in the preliminary stages to predictive simulations. Results of the modelling demonstrate strong geometric controls of the localisation of fluids during mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Corbett GJ

Epithermal gold-silver deposits occur in young volcanic terrains where post-mineral cover commonly impedes the search for mineralisation. At the Togi Project in Honshu, Japan, a complex mineralised system is largely covered by post mineral volcaniclastics. A combination of high resolution electrical resistivity surveying and detailed airphoto interpretation has, with close geological control, enabled synthesis of structural and alteration characteristics of the Togi geothermal system, in turn permitting ranking of the prospects for drill testing.

Jan 1, 1990

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

By LaBrooy S. R

Crushing for the gold industry involves fine crushing and a degree of primary milling, and this presents new problems and challenges, partiuclarly on many of the new ore-bodies now being opened up. All of this calls for a better understanding of some of the basics of fine crushing and milling. Accordingly, in this paper the "typical" contemporary Australian gold mining operation is firstly delineated, in terms of representative ore types and typical crushing and milling tasks. Then some of the technical and economic basics related to fine crushing are re-examined, including: energy relationships in crushing and milling; concepts of reduction ratio; recirculating load controversies; and questions of realistic economics in crushing gold ores. The economics of the typical gold mining operation are shown to be rather marginal; not the lavish "bonanza" many may imagine. Likewise, crushing cost expectations are frequently quite Unrealistic.

Jan 1, 1987

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

The capabilities of the three 61R and one 81R Robbins Raiseborers currently in use at Mount Isa are defined. Their applications in the development of ventilation and hoisting shafts, orepasses, escape routes, fill passes etc. are described and possible future uses of these and newer raiseborers at Mount Isa are examined. Problems associated with the use of raiseborers, together with ways of overcoming them are discussed. The impact of raiseborers on the mining operation is assessed in terms of new approaches to design and development, safety, cost and manpower efficiencies.

Jan 1, 1974

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

The investment worth of a mineral deposit can only be realistically evaluated in relation to specific engineering design criteria, which fully details the proposed method of exploitation. These criteria have not in general been taken into serious consideration when leaseholders have reported reserves in the past. In fact, many "reserve" figures quoted are probably more correctly classified as geological resources. The industry now recognises that it is necessary to take into consideration not only grade and mill recovery factors, but also likely mining and processing costs as well as the current market price for the commodity. Once having estimated those costs which are applicable to the resource under study, they can be deducted from the gross inherent worth of the orebody to result in an estimate of the potential net revenue. Through a process of interactive trial mine designs and evaluation, reserves can be quantified to provide an estimate of the available recoverable economic reserves given a set of assumed cost and operational parameters. It follows then, that the available economic reserve recoverable from a given resource will vary from time-to-time as cost and price factors vary in response to changing technology and economic factors. A methodology is described which may be used to derive economic recoverable reserves based on a computerised model of the geological resource data and appropriate economic and operational cost algorithms. Examples are provided from both coal and gold studies to illustrate the impact of economic criteria on the magnitude of the reserve figure reported for each project.

Jan 1, 1987

By R Farnf, M Pegden, S Hosein, T White

A number of theoretical papers have been published outlining the use of electronic detonators to limit peak particle vibrations levels, but few empirical studies have been undertaken and even fewer examples have been published of the use of such technology in the aggregates industry. This paper gives a summary of the research work carried out at two limestone quarries in the North of England, where a series of blasts were used to compare and contrast the use of electronic and non-electric detonators. The majority of blasts were carried out using the same burden, spacing and decked charge weight loadings. A methodology was established that could be used to reduce the peak particle velocities (PPVs) at two or more specific locations by using single-hole blast vibration signatures in conjunction with specific electronic detonator timing intervals. The initial study concluded that this was only possible if single-hole signature blasts were periodically recorded to establish the shape of the correct vibration envelopes as properties were approached. These wave envelopes could then be used as the basis for choosing the specific electronic detonator timing intervals to give the lowest PPV for the properties or locations concerned. This methodology was then used in the second study to access a large volume of aggregates adjacent to a working railway tunnel. The financial benefit for the company was to convert these additional tonnages of rock from being a resource to an exploitable reserve. The project involved careful blast design and the instrumentation of a number of boreholes to enable the results of blast monitoring exercises to be compared with predicted PPV results. The iterative process involved the vibration results being uploaded into æBlast LogÆ (an expert blasting database system developed by the Blasting and Environmental Research Group at the University of Leeds) and analysed to produce predictions ready for the next blast.

Jan 1, 2007

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

The dielectric properties of practically all oxide and sulphide ore minerals are such that they heat rapidly when irradiated with microwaves particularly at the standard frequency of 2450 MHz. The presence of carbon or low rank coal mixed with the minerals still further enhances the heating rate. Amongst the patented technologies being investigated are: (i) the direct reduction of oxides with or without carbon included in the pellets or briquettes; (ii) microwave precursor heating of composites ahead of smelt reduction; (iii) microwave smelting of ore or concentrate mixtures with carbon, sometimes assisted with oxygen. Microwaves appear to stimulate endothermic reduction reactions as readily as they do exothermic oxidation reactions. Being a method of achieving "bulk" heating, composites or columns of ore-char blends rapidly heat throughout rather than from the outside inwards as in conventional heating. The microwaves of themselves do not generate any gas - the only gases to be cleaned are the products of reaction in the composites or blends, plus the products of oxygen smelting. In the case of sulphide composites, depending on the quantity and type of low rank coal or char present, sulphur may be eliminated, and collected, in the elemental form. Furthermore, reactions seem to take place at lower temperatures than in conventional smelting but no doubt at the "points" where actual reactions are taking place the atomic or molecular vibrations are such as to satisfy the laws of thermodynamics. Examples are given of the production of unusual products of smelting sulphide concentrates and also the alloys produced from refractory minerals such as chromite and ilmenite. The techniques have been used to produce products with as wide a range of melting points as relatively pure tin and tungsten-molybdenum alloys. Special equipment is being designed and evaluated for these new fields of pyrometallurgy.

Jan 1, 1989

By G Kluck, N Stoitis, D R. Seaman, R A. Lauten

The presence of clays, in particular clay slime, may complicate many mining operations. Clay slime particles may possess a negative or positive charge depending upon the pH in the process and their presence may lead to reduced recoveries in flotation processes. It is assumed that slime particles may adsorb onto the surfaces of the minerals to be floated and by doing so, reducing the efficacy of the flotation chemicals. In this work it is shown that addition of a small amount of dispersant, either a polyacrylic acid or an anionic polyphenolic polymer, increases the recovery of copper and gold, both in laboratory trials and in plant testing of an ore with high clay content. Measurements of adsorption isotherms reveal that the tested dispersants show preferential adsorption towards the clay minerals present, suggesting that the improved recovery upon dispersant addition occurs by prevention of attachment of clay slime particles onto primarily chalcocite but also chalcopyrite.CITATION:Seaman, D R, Lauten, R A, Kluck, G and Stoitis, N, 2012. Usage of anionic dispersants to reduce the impact of clay particles in flotation of copper and gold at the Telfer Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012