Search Documents

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By Newell R

The influence of layering on the rate of heat transfer through a packed bed consisting of particles of two different sizes and heat capacities has been determined by measuring the heat front velocity through beds of quartzite particles and iron ore pellets. The heat front velocity through the layered beds was less than that through a bed consisting of a random mixture of the par- ticles. This is due to the formation of an interface in which the smaller pellets in one layer penetrate into the layer of quartzite Below.

Jan 1, 1987

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By Hutton W

The Argyle Diamond Mine is the first significant diamond producer in Australia. The project has been developed with new concepts in circuit design, process control technology, organisational development and training. After its first year of operation, the Argyle Heavy Medium Separation Plant has proven extremely efficient in recovering diamonds. Apart from cyclone wear, no major problems have been encountered. Ferrosilicon consumption is well below the design level which is a reflection of the sound design of the medium circuit. An Audit Plant continuously monitors the Heavy Medium Separation Plant tailings for diamond loss.

Jan 1, 1987

By Giannini L. M

Optimisation techniques, based on the block model, for solving the optimum pit limit problem were discussed in an earlier paper. Of the available techniques the one based on graph theory proved to be the most attractive. In the graph theory model the vertices represent blocks and the arcs represent the mining restrictions. For large ore-bodies direct application of the graph theory method poses considerable computational and storage problems. Techniques for easing the computational effort by reducingthe problem size were introduced in an earlier paper. Further, significant computational savings can be made by exploiting the structure of the graph. This is done by building the graph up level by level and successively applying the graph theory algorithm to reduce the number of blocks. In building up the graph in this way one needs what is called a "search pattern" to indicate which arcs are to be added as new vertices are introduced. Moreover, as it is essential to keep the number of arcs to a minimum it is necessary to establish a "minimum search pattern".The problem of determining minimum search patterns for any block model and for any wall slope restrictions has not been considered in the literature.The objective of this paper is to present a complete solution to this problem and to discuss, through typical case studies, the application of the associated software developed.

Jan 1, 1988

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

By N Wharmby

In recent years in New Zealand there have been a number of tunnelling and deep directionally drilled pipelines projects that have required access shafts. Often these shafts are in urban environmentswhere vibration and high noise levels are not tolerable. There are a number of methodologies that can be adopted dependent upon the shaft plan area, depth and geology.This paper will describe some different methodologies that can be adopted that use piling methods such as large diameter piles, and secant piles. The paper will use case studies to highlight:· construction methodology,· specific methodology issues and constraints,· lessons learnt, and· recommended specifications.The development of piling technologies in New Zealand has enabled the development of cost effective solutions for the construction of deep shafts in sensitive urban environments.

Mar 8, 2011

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

The region we call the West Coast is acknowledged as one of the richest and most diverse mineral provinces in the world. It's the most rugged part of Tasmania and our island is one of the most rugged parts of Australia, so that speaks for itself. A hostile land of razorback mountains, deep ravines, dangerous rivers, almost impenetrable rainforests and a climate that can change from mild to freezing in a matter of hours.

Jan 1, 1993

It is often assumed that geotechnical investigations or studies for open pit mines are confined to providing a slope design. However in an operating mine, the design is only one component of a mine geotechnical program. Reviews of slope designs are ongoing throughout the mine life. The concept of Pit Slope Management has been formulated because the design only entails one component of a total program that contributes to a safe, efficient mining operation. Risk is a normal part of mining. Effective management allows the risk to be contained or controlled. If the slopes are not effectively managed there will be increased risk for the operation. Experience has shown that utilisation of Pit Slope Management coupled with a broad base of experience to define the key controls on stability, provides a pro-active, objective approach. The reasoning is deductive and relies on the behaviour of the ærocksÆ. Once the key aspects are defined, studies are well focused, implemented as required and the risks can be effectively managed. When the key controls on stability are poorly understood reasoning is typically more ægut feelÆ. Under such circumstances studies, if carried out, may meet short-term objectives but often ignore the long-term objectives. Hence the risk to the project is greatly increased. This paper presents several case studies highlighting the above aspects and present elements of the Pit Slope Management Program approach which have been successfully utilised by the author to manage risk in mining projects.

Jan 1, 2003

The different electrowinning cells presently developed for recovery of gold from CIP eluates are compared and contrasted. The efficiency of operation for each cell is,discussed in terms of the electrochemistry of (a) gold deposition, and (b) packed bed electrodes. The advantages and problems associated with each cell design are presented and recommendations are made as to the best method of gold recovery.

Jan 1, 1982

This paper records the observations of faulting in the Black Star mine workings. By classifying the faults into two groups, i.e., strike faults and transverse faults, and by pointing out the differences between the groups and their effects on the silver-lead-zinc orebodies, a time relationship between the two groups of faults and the sulphide mineralisation is suggested.GENERAL GEOLOGY AND MINERALISATIONFolding and faulting are closely related to the mineralisation in the shales by silver-lead-zinc and iron sulphides.Commonly the various sulphides are fine-grained and closely associated with one another. However, exceptions do occur locally, where massive coarse galena, sphalerite, pyrite, and to a lesser extent chalcopyrite, have been observed singly or closely associated one with the other.In the main, the sulphide mineralisation forming the orebodies occurs as replacement of, and infilling along, the sheared bedding planes of the finely bedded shale host rock.The shales in general strike north-south with an average dip to 60° to the west; strong shearing along the bedding planes is evidenced by much slickensiding and slaty cleavage.Sequences of finely bedded shales of varying stratigraphic thicknesses alternate with very. massive beds, and it is in the more highly sheared thinner beds that the greatest concentration of sulphides occurs. The unmineraIised massive beds of shale, 11 in. up to 12 in. in thickness, occur singly or in groups between, and to a lesser extent. within, the orebodies. The massive beds resisted sulphide replacement and impart to the orebodies a most prominent banded structure.

Jan 1, 1953

Grinding is probably the single unit operation that requires the largest capital investment and operating costs in an ore beneficiation plant. Because of that, a great deal of research has been concentrated in the theory, design and operation of grinding equipment, in particular ball mills. To-date, the models developed to describe grinding in tubular mills are macrophenomenological and can be divided into two categories: energetic and kinetic models. This paper presents a new approach to modelling ball mill grinding: The Operational Model. The theoretical aspects of the model as well as a comparison with existing ones are discussed. The concepts of the model, summarised in easy-to-operate PC programs, permit the calculation and design of new ball mills, and a critical evaluation and optimising of mills in operation.

Jan 1, 1993

The techniques used in evaluating gold placers and in recovering gold therefrom are briefly reviewed and critically assessed, relative to the estimated and actual recoveries from many operations. The discrepancies between these quantities can be significant and sometimes disturbing. The coefficient of variation for the annual percentage recoveries, relative to the estimates, is in excess of 10 and commonly above 20 . The difficult- ies in evaluating placers are recogni- sed both in the gathering of meaning- ful sample data and in the derivation of estimates. There are deficiencies, perhaps insurmountable at reasonable cost, in the techniques used to derive an estimate and in the gold saving devices usually employed. There is a subconscious trend to use recovery as a check on the estimate. The industry could have extracted more information during the evaluation and working of deposits in order to fully characterise them and in order to quantify metallurgical efficiency. There is a place for other prospecting techniques, particularly geophysical, in placer evaluation and a need for more appropriate and sophisticated

Jan 1, 1976

Systematic ICPES (Inductively coupled plasma emmission spectrometry) analysis of magnetic concentrates from drainage samples has been used to discriminate concentrates dominated by magnetite from those dominated by pisolites, presumably maghemite-rich. In addition, a set of spurious zinc enhancements was recognised and explained with the help of mineralogical data, and systematically isolated using chromium as a Discriminator.

Jan 1, 1987

A modular computer-based monitoring system for mines is dis-cussed. The system consists of the following modules : production moni-toring system HADES, methane monitoring system CMC, seismoacoustic and seismometric systems SAK and SYLOK, communication systems. The system enables one to compose flexible,` economic structures according to the specification of a mine. Application of microcomputer-based monitoring and control systems in coal preparation plants also is discussed.

Jan 1, 1985