Search Documents

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By D. A. MacLeod

DURING the past fourteen months, dust surveys have been made at thirty-six mines in the Province. These surveys are made to determine the concentration of dust in the mine atmosphere, the flow of air through the mine, the methods adopted to prevent the generation of dust, and the measures taken for its elimination. When high concentrations of dust are encountered, suggestions are given for its prevention ?and elimination wherever possible. Dust sampling is absolutely necessary to determine the effectiveness of any measure taken in the prevention and elimination of dust in the mine workings. Consequently, more time has been spent on this phase of the work than on any other. The apparatus used is the Devers circular konimeter and Zeiss microscope. At various mines, the Zeiss konimeter is used, and the dust counts taken by the two instruments have given results that are closely comparable; so much so that either instrument can be used with confidence and the results obtained will compare in accuracy with those obtained by the methods used in Ontario and South Africa. Before the Workmen's Compensation Act Amendment Act was passed in November, 1936, most of the mine operators were already keenly interested in the prevention of silicosis. This interest has been intensified at all the mines, and measures have been adopted to decrease the amount of dust in the mine atmosphere. Several operators have spent a large amount of time and money in bettering these conditions, and have met with decided success. Practically all others are adopting the known methods of prevention, suppression, and elimination of dust, that apply to their ?particular mines. To prevent the production of dust in underground workings should be the first, as it is the most important, aim, especially during the time the men are underground. An atmosphere free of dust cannot be obtained, but measures can be adopted to lower the concentration that is found? in the average mine.

Jan 1, 1939

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By Claude Bazin

"The On-Stream Analyzer has proven and is still proving to be an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the provided assays using a real-time material balance program to calculate the distribution of solids within the streams of a circuit. Mass balance results can be used for process control, process analysis and detection of sensors malfunction. Examples from 3 Canadian and one American concentrators are presented to illustrate the potential of the method.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants is increasing. On-Stream Analyzers provide X-rays pulse counts that are converted into assays using multilinear regression programs. The estimated assays are passed to the flotation operators, via an operator console, or to control loops of various degrees of complexity (McKee, 1991) implemented in a Distributed Control System (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one should ask: Could we get more from the OSA?Some plants reported the use of OSA measurements to process optimization (McKee, 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2 product formulae (Wills, 1992, page 124). The 2 product formulae is however sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al., 1993). Least squares algorithms provide an interesting alternative to filter out measurement errors (Spring, 1992). This paper presents a recursive least squares algorithm that estimates in a real time fashion the mass flow rates in a flotation plant using OSA and mass flow measurements. The algorithm is robust and its recursive structure is not demanding in terms of computation time and memory. The method was tested with data from four concentrators. Results of the material balance algorithm prove to be useful to detect sensors malfunction and may potentially be used for the control and optimization of flotation plants.The paper is divided into two sections. The first section gives a description of the proposed method. The mathematics of the method are kept to a minimum, since the detail is presented elsewhere (Bazin and Franklin, 1994). The second section shows the application of the method to different flotation plants."

Jan 1, 1995

By P. Ramirez

"To achieve an optimal metallurgical performance in the flotation process the bubble diameter should be between 0.5 and 2.5 mm. To control bubble size, frothers are added, reducing bubble size and conferring bubble stability against coalescence. However, the bubble generation mechanism determines predominantly the bubble size distribution produced. In mechanical flotation cells, bubbles are produced by the shear stress generated by a rotating blade on a gas stream. This mechanism produces a log normal bubble size distribution. In contrast, in column flotation, jetting gas injectors are commonly used in Chile and the bubble size distribution is bimodal with small and large bubbles. Bubbles larger than 2.5 mm mean a loss in surface area, while bubbles smaller than 0.5 mm move with the pulp stream and therefore collide less frequently with particles. In this paper, a new device based on a jetting sparger and a deflector disc (impinging jetting) is evaluated as an alternative sparger for column flotation.The new device was tested in a rectangular acrylic cell 1 m × 0.5 m × 3 m. High-speed cinematography was used to compare bubble generation with jetting and impinging jetting at different gas velocity in the nozzle (5–50 m/s). From the image analysis, it was observed that the deflector induces a shear stress, in analogy to a rotating blade but in this case the shear results from a high velocity gas hitting a static surface. The device was evaluated in a 0.5 m diameter 3 m high column. The McGill bubble viewer technique was used to compare the bubble size generated by jetting and impinging jetting. It was found that the Sauter mean bubble diameter reduced from 7.4 mm to 2.8 mm, when the jetting sparger was modified with the deflector. In the case of the impinging jetting sparger, 70% of the bubbles were in the effective range for flotation, while for the jetting sparger, only 10% were in the effective range."

Jan 1, 2016

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By Ross Byron, Ken Roberts

"During the fall of 2001 a program was initiated to determine the feasibility of improving the metallurgy in the flotation circuit at the Penhorwood Talc Concentrator located near Timmins, Ontario. Bench scale testwork led Plant staff to believe that opportunities existed to improve the flotation performance. Pilot scale testing was then conducted using two vendors and their respective cylindrical type flotation cells to indicate where these opportunities existed.The results of the test program determined that the replacement of the existing flotation circuit (roughers, scavengers and cleaners) with new flotation cells could be economically viable. Justification was due to a reduction in installed horsepower, maintenance costs and a subsequent increase in recovery and throughput while maintaining product quality. Unforeseen benefits included reagent and air reduction, accurate level control as well as improved working conditions due to the removal of the antiquated equipment and ancillaries.This paper will detail the justification, installation and implementation of the new flotation circuit. A special emphasis will explain the hurdles encountered while trying to install and commission the circuit in an operating Concentrator with minimal interruptions to production.INTRODUCTIONThe Penhorwood mine and Concentrator is 28 yrs old and has gone through many ups and downs with different owners, Johns Manville, Steetley Talc and now Luzenac. It has also been expanded twice, with flotation and grinding capacity being added in recent years.All of the concentration is completed at the mine site while the fine grinding takes place in the Timmins micronizing plant.Luzenac’s Philosophy is to be the world leader in Talc production, technology and sales, having about 70% of the current world High Grade talc market."

Jan 1, 2004

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By Stephen G. Mlot

The evaluation of mineral projects involves the identification, mitigation and management of significant uncertainty. Benchmarking is an essential and effective way of increasing confidence and reducing uncertainty associated with input parameters and assumptions. Comprehensive and detailed benchmarking will ensure ?best practice? technologies, methods and systems have been considered and that the appropriate practices can be identified and incorporated into the project. In conjunction with the involvement of experienced industry practitioners, benchmarking is best employed throughout project evaluation to enable early identification of ?errors?, producing more accurate and predictable outcomes. Considerable time and effort is required to gather data and information, which should be benchmarked by the project evaluation team. There is a history of mining projects underperforming, on production, on costs and on return to the investors. The quality of mine plans and feasibility studies, and the quality of the input data is being questioned in many ways. Benchmarking assists sound project evaluation practices, by providing a database of actual results, to validate project inputs and outcomes, ensuring they are realistic and achievable. Benchmarking also provides unbiased, statistical support as the basis for sound investment decision making and ensures well considered decisions are made resulting in a more efficient study process. The evaluation of the quality of projects which are the subject of transactions also benefits from the use of real data obtained from a benchmarking database. Vendors are quick to highlight the benefits of their projects, and conceal the flaws, inflating the value. Buyers will want to quantify the potential of a project through the due diligence process relying on actual results from benchmarking. For the reasons broadly outlined above, benchmarking should be considered as an essential component of effective Project Evaluation.

Aug 1, 2013

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By R. Simkus, J. K. Gowans

Polaris Operations, a Cominco Ltd. lead-zinc mine, is located on Little Cornwallis Island, Northwest Territories, at Latitude 75°23' N and Longitude 96°75' w. When the Polaris Mine went into operation in late 1981, it became the world's most northerly base metal mine.The Polaris Concentrator, housed in a unique process barge, is a basic lead-zinc concentrator where flotation is used to produce the lead and zinc concentrates.The paper describes the ""coarse lead"" flotation feature incorporated in the concentrator flowsheet and describes the start-up problems and continuing operation of this circuit.

Jan 1, 1984

By B. Meddings, O. J. I. Evans

"This paper is mainly concerned with the present and probable future role of hydrometallurgy in the production of base metals.The economic and technological bases of the hydro-metallurgical plants built and operative in the mid-fifties are compared to those in production in the mid-sixties. The trends observed are extrapolated and some estimates made concerning the probable size and type of hydrometallurgical plants which will be operative in the mid-seventies.The impact of emerging socio-economic factors such as pollution control and the market demand for specialized metal products which favour hydrometallurgical recovery processes are also discussed."

Jan 1, 1971

By E. H. Rose

THE most useful guide to the role of lime in flotation is the view that the chemistry of any flotation operation is primarily a pattern in relative solubilities. We have the coming together of a number of minerals, reagents, fortuitous salts, water, and oxygen, many of which have not been previously in contact with each other, and every one of which is free, at least to some extent, to abandon old alliances and to form new ones. Of one thing the operator may be sure, and that is that, when equilibrium has been reached, those new chemical combinations will have formed which are the least soluble combinations possible to the environment. The laws of solution govern the operation, which means that relative concentrations are always a factor, and temperature frequently is. What the operator is really doing when he chooses his reagents .in the first place (empirically or otherwise) and works out their? optimum amounts, is to provide an environment in which (1) the least soluble possible compound of the mineral he desires to float is one which is also non-wettable, while at the same time (2) the least soluble compounds possible to the minerals he desires to depress are wettable. Since all metathesis is reversible, perfection is impossible to achieve, and the operator is constantly striving to establish that combination of concentrations which will drive each and every particular reaction as far as possible in the direction he desires it to go, in accordance with the law of molar concentration.

Jan 1, 1939