Search Documents

By Steve Lalancette

Centre Jardin Lac Pelletier (CJLP) has been a leading actor in the revitalisation of closed mining sites in northern Québec for over 20 years. Over that period, CJLP developed a cost-efficient technique that transforms sterile mining residue into a substrate able to support a resilient ecosystem. Using a unique mix of organic matter, fertilisers and selected plant species, this technique rapidly builds a microorganic fauna and a layer of humus that will sustain the creation of vegetation coverage. The coverage is composed of over 13 different plant species, each having a unique role in the development of a resilient ecosystem, from soil stabilisation to nitrogen fixing. Considerably less expensive than traditional methods using civil engineering techniques, it does not require the use of heavy machinery or the spread of topsoil. This technique has been successfully used to restore over 20 sites in Québec such as Joutel, Yvan Vézina and Louvicourt. It is a proven technique that has passed the test of actual implementation. The presentation will review the biological, production and economic aspects of the technique through the revitalisation of the Joutel site.

May 1, 2011

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By S. Y. Tshipeng, A. T. Kaniki

"RÉSUMÉ La lixiviation acide d’un minerai oxydé cupro-cobaltifère en milieu non réducteur et en milieu réducteur en utilisant le Fe2+ et le métabisulfite de sodium (SMBS) a été étudiée et les résultats ont été comparés. Les tests de lixiviation ont été effectués à température ambiante, dans une pulpe à 30 % solide, avec une vitesse d’agitation de 600 tr/min, un potentiel redox de 350 mV pour les tests en milieu réducteur, et un pH de 1,8. Les tests de lixiviation avec usage du SMBS comme réducteur ont donné la meilleure cinétique de lixiviation du cuivre. Pour le cobalt, c’est l’usage du Fe2+ qui a donné la meilleure cinétique de lixiviation. L’augmentation de la dose du fer dans la solution au-delà de 5 g/L a influencé négativement les rendements de lixiviation du cuivre et du cobalt. ABSTRACT Acid leaching of a copper-cobaltiferous oxide ore in a non-reducing environment and in a reducing environment using Fe2+ and sodium metabisulfite (SMBS) was studied and the results compa¬red. The leaching tests were performed at room temperature, in a 30% solids pulp, with a shaking speed of 600 rpm, a redox potential of 350 mV for the tests performed in the reducing environment, and a pH of 1.8. The leaching tests using the SMBS as a reducing agent produced the best copper leaching kinetics. As for cobalt, the best leaching kinetics was achieved using Fe2+. An increase in the amount of iron in the solution above 5 g/L negatively influenced copper and cobalt leaching yields. INTRODUCTION La République Démocratique du Congo (RDC) est un pays reconnu dans le monde pour son sous-sol qui regorge d’énormes quantités de cuivre et de cobalt (USGS, 2014; Palisade Research, 2016). La technique qui semble être la plus recommandée pour extraire à la fois le cuivre et le cobalt des minerais oxydés cupro-cobaltifères est la lixivia-tion acide en milieu réducteur. Cette technique est appliquée par la majorité des sociétés minières qui exploitent ces minerais dans l’ex-province du Katanga en RDC, à savoir: Tenke Fungurume Mining, Mutanda Mining, Kamoto Cop¬per Company, Sicomines, Gécamines, Boss Mining, Chemaf, Ruashi Mining et Somika. L’usage d’un agent réducteur est indispensable pour l’obtention d’un bon rendement de lixiviation du cobalt. En effet, plusieurs chercheurs s’accordent sur le fait que le cobalt trivalent de l’hétérogénite (CoO·2Co2O3·6H2O) est insoluble à l’action de l’acide seul; il ne devient soluble qu’après réduction en cobalt bivalent (Mwema, Mpoyo, & Kafumbila, 2002; Mulaba-Bafubiandi, Ndalamo, & Mamba, 2007; Ferron, 2008; Seo, Choi, Kim, & Tran, 2013; Stuurnam, Ndlovu, & Sibanda, 2014)."

Jan 1, 2018

By Karl J. C. Harries

This paper looks briefly at some of the agreements and types of royalties that may be met during exploration activities, but does not go into details relating to them. Agreements can either make or break a deal or relationship. A well drafted, comprehensive and fair agreement can create good relations and trust among the parties and will go a long way towards making a deal work. In the best of all worlds the agreement will be put away and not need to be referred to after it has been signed (but it will be there if needed to sort out potential problems). On the other hand, a poorly drafted agreement or one that is inappropriate to the circumstances or unfair to one of the parties can break a deal and end up with the parties facing each other in that expensive, unproductive and time-consuming occupation ? a lawsuit. Accordingly, it is advisable to involve professional advisers with any agreement. The straightforward one may involve no more that a read through whereas the more complex agreement will require considerable involvement. There is, however, one rule for every explorationist to remember: a professional adviser is only an adviser. His responsibility is to make sure that you have the necessary information to make a reasoned decision but the decision is yours, not the adviser?s. It is your deal, you are going to have to live with it, and it is inappropriate for an adviser to introduce new concepts or amend negotiated ones without your specific instructions. Mineral exploration agreements, although basically option, acquisition and joint participation agreements, come in all the shapes and forms, appropriate to give effect to the endless variety of deals negotiated by the ever-active minds of explorationists. You will note the reference to "joint participation agreements" rather than "joint venture agreements". The latter term was purposely avoided because, with the current activity of explorationists from common law jurisdictions in civil law jurisdictions, it has become necessary for the explorationist to become familiar with corporations and shareholders agreements. As most of you are no doubt aware, under the civil law system a joint venture is normally not recognized as a legal entity and, therefore, joint participation in projects is usually by way of corporations.

May 1, 2003

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By Akiyoshi Horiuchi, Manabu Kanno, Shigeki Sato, Taro Aichi

"AKITA ZINC Co., Ltd. (Iijima Zinc Refinery), jointly owned by DOWA METALS & MINING Co., Ltd.(DMM), has used the company’s own hematite process for iron control since the beginning of operations in 1971. The hematite process consists of reductive leaching with SO2 gas and iron removal in autoclaves by high temperature hydrolysis. This process enhances not only zinc recovery but also the recovery of gold, silver, copper, lead and rare metals, which is carried out at another DOWA metallurgical plant. All by-products produced in the hematite process are marketed and sold. This paper presents an overview of the hematite process and the recent process improvements made.INTRODUCTION DMM carries out mining and smelting activities for precious metals, PGMs, rare metals and base metals such as copper, lead and zinc. It owns KOSAKA SMELTING & REFINING, producing copper and lead, and the AKITA ZINC Co., Ltd. (AZC) in Akita Prefecture. DOWA is a specialized smelting company which has established a metallurgical complex for copper, lead and zinc, including a recycling business. AZC was established in 1971 at a production capacity of 72,000 t/y zinc; it is jointly owned by DMM and five other non-ferrous metal companies. AZC has increased its capacity continuously and now produces 210,000 t/y of zinc. Figure 1 shows the changes in zinc production and capacity at AZC."

Jan 1, 2016

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004

By W. F. Giuvlore, E. Mcroberts, T. S. Golosinski

"The rising demand for Canadian coal and depletion of shallow deposits, most suitable for surface mining, result in rapidly increasing volume of waste materials which have to be moved by the coal mining industry. While at present this challenge is being successfully met using conventional mining methods, in the future, innovative methods must be considered if Canadian coal is to remain competitive.The need for more efficient mining methods is also faced by the oil sands industry to assure competitiveness of the synthetic oil price.A look at the world mining practice indicates that large volumes of material can be economically mined and moved by the continuous mining systems comprising bucket-wheel excavators, belt conveyors and stackers. To assess the state of art and applicability of this mining method to Canadian conditions, the field trip was organized by the Department of Mining Engineering o f the University of Alberta, to several typical mining operations in Europe. It is in Europe where the continuous mining methods were developed and are almost exclusively used in large-scale surface mining."

Jan 1, 1984

By Ron Jessulat

"IntroductionBrunswick Mining and Smelting Corp. Ltd. is a IO 500 tid base metal producer. Development is carried out by Jarvis Clark MJM-21 3-boom development jumbos, using Tamrock E400, 410 and 550 pneumatic drills. Typical drift size is 13 ft by 18 ft with a 12-ft advance per round. Blast holes are 1 ½ in. in diameter while reamed holes are 3 in. in diameter. AN/FO is the principal blasting agent, being loaded by C-I-L model60R intermediate loader. The detonators are NONELS and DETINELS. Sulphide dust explosions occur during blasting when dusts from certain minerals such as pyrite and pyrrhotite are ignited by name from the detonating shots. The result is a secondary unwanted explosion with a characteristic shock wave and name front that are very destructive to mine services such as ventilation ducting, electrical cable, and ventilation control doors.A typical reaction in the Brunswick orebody occurs according to the chemical formula:4FeS 2 + IIOs-2Fe2O3 + 8SO2 + 3458--(Enright , 1988)The hematite (FeO3) is deposited as a red dust in the blast area while the toxic sulphur dioxide gas (S00 contaminates the underground workings . The presence of S02 gas disrupts production until it is purged from the area by the mine ventilation system or dissipates slowly in those areas where the vent ducting has been melted by the name front or torn down by the shock wave.Sulphide dust explosions exact a high economic toll. Direct costs in damaged materials and wages are probably exceeded by the value of lost production and disruption to the mining cycle. In addition, the health and safety concerns associated with sulphide dust explosions cannot be ignored."

Jan 1, 1993

By J. Zou

Open-cut method is most widely used for shallow utility lines installation. In urban areas, unexpected utility lines buried underground potentially turn open-cut construction into a highly risky operation, increasing the construction cost while presenting additional safety hazards. Examples include: breaking existing water main leads to flooding the downtown area; hitting an unexpected gas line causes an explosion. To prevent those accidents, the current practice is to stake out the underground utility lines before the open-cut construction based on the as-built information collected from various utility companies and government agencies. However, the as-built information is not always complete and accurate. To verify the locations of some important utility lines and protect them against damages caused by open-cut construction, new techniques and technologies are used but have their limitations in revealing underground utility lines, such as hydro vacuum method and ground penetration radars (GPR). The emerging technology of ultra-wide band (UWB) radar holds the potential to provide a cost-effective, non-destructive detection method. In this paper, a critical review of current practices and established methodologies is given. The functionality and working mechanism of UWB radar technologies are described. Application potential in open-cut construction is demonstrated by conducting lab experiments. Testing set-ups for detecting unexpected utility lines in soil along with preliminary results are presented. The effects of soil moisture content on the detection range are discussed. Research findings are summarized and constraints are discussed in conclusions.

Aug 1, 2013

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

By N. Sauret-Szczepanski, G. Patry, S. Gauthier, G. Potvin, C. Munger

Adsorption/thermal desorption with sorbent cartridges and analytical method using gas chromatography coupled to mass spectrometry (GC/MS) was developed for the determination of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) emitted from primary aluminum smelters. A customized cartridge was built like a packed column with a stainless steel tube filled with a specific resin. The optimization of adsorption and desorption parameters was carried out to support the PFC sampling for all aluminum production technologies. The proposed method showed good linearity for concentrations ranging from 10 to 500 ppbv for CF4 and from 5 to 500 ppbv for C2F6 with correlation coefficients above 0.999. In certain conditions, the detection limits of the analytical method reached 0.3 ppbv for CF4 and 0.15 ppbv for C2F6- Using this methodology, a field campaign was carried out using a sequential sampler allowing the simultaneous sampling of PFC with cartridges and sampling bags. The results showed no significant difference (t-test) between the two sampling technologies and no breakthrough was observed from the cartridges .

Jan 1, 2006

By C. A. Petch

Abstract - The High Lake polymetallic deposit is located in the northern Slave province, 40 km south of Coronation Gulf, Nunavut. The main zone, the AB zone, hosts an estimated resource of 3.56 Mt grading 5.0% copper, 1.1% zinc, 0.06% lead, 1.7 g/t gold, and 18.2 g/t silver. Archean felsic metavolcanic and metavolcaniclastic rocks are the dominant rock type and are associated with lesser mafic metavolcanic and carbonate-rich metasedimentary rocks. The sequence strikes north-northeast, dips steeply to the west, and is truncated to the west by a large granodioritic intrusion. The mineralization at the AB zone is comprised of massive and stringer chalcopyrite-sphalerite-pyrrhotitepyrite± galena. At the core of the mineralized zone, intensely chlorite-altered rocks are locally metamorphosed to form distinctive zones of anthophyllite-magnetite-cordierite-altered rock. Peripheral to the mineralized core, alteration consists of sericitization, silicification, and weaker chloritization. Primary morphology and facing direction of the zone are difficult to interpret in part due to poor primary metal zonation of the deposit. However, the irregular shape of the mineralized zone and the erratic zones of zinc enrichment at the fringes are consistent with the interpretation that the zone was formed by the replacement of a porous volcaniclastic pile.

Jan 1, 2004

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By A R. Bullis

Metal Mines Limited (Bancroft Division) was incorporated m 1964 to take over the assets of Faraday Uranium Mines Ltd., including their uranium deposit near Bancroft. Ontario. This paper outlines the geology of the Bancroft area, and. then go on to describe the principle rock types m the mine workings, especially the pegmatite, which is the host rock for the uranium mineralization. The structure and mineralogy of the orebodies are thoroughly covered, and, after a summary of the production and ore re-serve figures, the paper concludes with suggestions for further exploration work. Location and History M ETAL Mines Limited, Bancroft Division, is located in Faraday township, Hastings county, Ontario. The main production shaft and concentrator are about: Y2 mile north of Highway 28 and about 5 miles west of the village of Bancroft (Figure 1). The presence of radioactive minerals in the Ban-croft-Wilberforce area has been known since the early 1920's. Uraninite was found at the Richardson deposit near Wilberforce in 1922, and some attempts were made to produce radium from the deposits of the area between 1929 and 1931.

Jan 1, 1965