Search Documents

By T. Hadley, Northern Minerals Ltd, C. S. Griffith, T. A. Safinski, K. H. Soldenhoff, M. Fainerman-Melnikova, A. Manis

"ANSTO Minerals and Northern Minerals have been working together since 2012 on the process flowsheet development for the Browns Range project for the recovery of the heavy rare earths (Dy – Lu, + Y). Initial efforts were directed toward defining the most efficient and direct flowsheet for the Preliminary Feasibility Study (PFS), issued in June 2014, then towards the Definitive Feasibility Study (DFS), issued in February 2015. These goals were achieved by undertaking comprehensive laboratory and continuous piloting programs. Further improvements to the flowsheet following the DFS have been made. This publication provides an overview of the evolution of the process flowsheet based on these laboratory and piloting programs from the PFS through the DFS and beyond.INTRODUCTIONNorthern Minerals Ltd (Northern) has been working on developing their flagship project at Browns Range for the recovery of the heavy rare earth elements (HRE, Dy – Lu, + Y). The project is located in the north of Western Australia as shown in Figure 1. The Total Mineral Resource at the project is currently estimated at 8.98 Mt @ 0.63% total rare earth oxides (TREO) comprising 56,663 t of contained TREO using a cut-off grade of 0.15% TREO. Of the Total Mineral Resource, 58% is classified as Indicated Resource, with the remainder in the Inferred Resource category.The deposit is characterised by breccia-hosted, hydrothermal, HRE-rich, xenotime mineralisation. The main gangue mineral associated with the xenotime is quartz. The distribution of rare earths (RE) observed for the xenotime mineralisation at Browns Range is presented in Figure 2. Extensive test work has shown that the xenotime can be readily beneficiated to between 20 – 40% rare earth oxide (REO) using a process consisting of crushing and grinding, followed by magnetic separation and flotation steps. Continuous piloting of this process was conducted on ~80 t of trench-sourced ore in late 2013 at SGS Perth, to produce ~2 t of ~20% REO mineral concentrate (MC) for hydrometallurgical testing. The composition of the MC produced during piloting is presented in Table 1."

Jan 1, 2016

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By Ibrahim Ocak

The prediction of machine utilization time and determining machine performance plays an important role in scheduling and planning tunnel excavation and data base created serve a major role in further applications. In this study, the construction methods of two twin tunnels situated between Basak Konutlari station and Istoc station are summarized. Geology in the study area is composed of fill and weak rock, respectively starting from the surface. The tunnels of 5.6 km in length were excavated with two different earth pressure balance machines (EPBM). Excavation diameters of the EPBMs were 6.564 m. The performance of the machines are analyzed and compared in order to accumulate data for further applications in similar ground conditions in Istanbul. The distance between two twin tunnels is 14 m from center to center and the EPBM in the one tube was almost about 100 m behind the other tube. Segmental lining with 1.4 m of length and 30 centimeters of thickness were used as final support. The overall performances of the two Lovat TBMs are found to be respectively as; the best daily advance rates 30.8 m/day and 30.8 m/day, the best weakly advance rates 115.0 m/day and 153.9 m/day, the best monthly advance rates 388.7 m/day and 400.5 m/day. Total waiting and maintenance times were 25.2 and 16.7 %, respectively.

Aug 1, 2013

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By L. Tong

"The oxidation of Quebracho was evaluated by acid-butanol assay, which indicates depolymerization of Quebracho. Anthocyanidin, an oxidation product of Quebracho, is stable at 95?C for up to 2 h. The ionization, complexation, and oxidation properties of Quebracho were discussed. Complexation of metal-Quebracho occurs at ambient temperature. The formation of complex precipitates is influenced by the acidity of the solution. Temperature is another important parameter that influences the oxidation and the complexation of Quebracho. Quebracho-ferric complex precipitate forms at 90?C, 0.1 mol/L H2SO4. The formation of Quebracho-metal complex in the leach solution is a possible reason for the consumption of Quebracho. Quebracho molecules adsorption on the mineral surface is reduced by consumption of Quebracho, resulting in poor sulfur dispersing effect in the leaching process. INTRODUCTIONQuebracho is used as a sulfur dispersing agent (SDA) in the pressure leaching of zinc concentrate as stated in U.S. Patent No. 3,867,268 (1975). It prevents the zinc sulfide particles from being coated with molten sulfur, thus preventing the inhibition of the zinc leaching reaction. Recently, the sulfur dispersing effect of Quebracho was investigated in the oxygen pressure leaching of nickel concentrate. The oxygen pressure leaching of pentlandite can be represented by reactions 1-3."

Jan 1, 2012

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By Antonio Fontana

"Environmental problems encountered with the use of diesel equipment in underground mining operations are discussed. The concept and procedure o implementing the Health Effects Index equation as a means of quantitatively assessing an underground working environment is outlined and sample calculations are present ed. Advantages and disadvantages of utilizing this method are also discussed.IntroductionWith the introduction of diesel-powered mining equipment in the 1960s there arose several question s for the environmental engineer to consider. These included: 1. What are the constituents of diesel exhaust and how can they be detected and evaluated?2. What are the toxicities and long-term health effects of these constituents?3. What is the ventilating volume required to maintain the concentration of these constituents below toxic levels?Diesel engines are a class of reciprocating, internal combustion engines in which relatively high compression ratios are used to generate high air-charge temperatures, which cause ignition of fuel to occur spontaneously. Ideally, perfect combustion of the fuel would produce an exhaust consisting solely of nitrogen (N2), water (H2O), carbon dioxide (CO2) and oxygen (O2). However, because no combustion process is perfect, relatively small quantities of imperfect-combustion products, or pollutants, are also generated. These include hydrocarbons (HC), carbon monoxide (CO), nitric oxide (NO), nitrogen dioxide (NO2), carbon (C) or soot, and sulphur dioxide (SO2).Currently, the Regulations for Mines and Mining Plants, made under the Occupational Health and Safety Act (Section 176), stipulate that weekly tests shall be made to determine the carbon monoxide (CO) concentration in the undiluted exhaust and at the operator's position, and the nitrogent dioxide (NO2) concentration at the operator's position. Also, the aldehyde (as HCHO) concentration in the atmosphere, at the operator's position, is to be measured at least every three months. Threshold limit values (TLVs) have been established for each of the three combustion products, and each is regarded as a separate entity. Consequently, this does not allow for consideration of interactions and possible synergistic effects between the various exhaust components."

Jan 1, 1982

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By A. Ducastel, S. Connemann, A. Stark, F. Bouillot, C. Fricke-Begemann, LSA, H. Knapp, L. Horckmans

"Refractory materials are essential for all high-temperature applications in industry. Depending on the position in the furnace and specific process requirements, refractories are produced from several raw materials, such as dolomite, magnesite, bauxite, graphite or chromite. Most of these raw materials are not rare but strict quality requirements limit the producers of refractories to only a few deposits in the world. Thus, raw material supply is a critical factor for the production of refractories and accounts for 40-50 % of the total costs of refractories.A possible way to lower dependency on raw material supply is recycling of spent refractories. Main challenge in recycling is the separation of different brick types from each other and the removal of impurities, such as steel or slag. The European FP7 project REFRASORT aims to apply sensor-based sorting for separation of spent refractories. Sensor-based sorting is known from food industry, recycling and mineral processing and has proven its reliability. Nevertheless, some adjustments are necessary compared to applications in mineral processing because of other sensor-types and a higher number of products in one sorting step. This paper presents the results of feasibility tests for sensor-based sorting of refractories with near infrared spectroscopy and laser-induced breakdown spectroscopy (LIBS). Both sensors showed the potential to identify different brick types but the most promising results were obtained using LIBS technology. INTRODUCTIONRefractories are solid, ceramic products, which can sustain temperatures of more than 1500°C, without losing their stability or shape. Bricks of refractories have to withstand corrosion in contact with liquid steel or slag. Various high temperature applications, such as the production of glass, steel, copper or cement, require high quality refractories. The quality requirements of refractory bricks are strict, because small impurities can lower the thermal strength significantly."

Jan 1, 2016

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By F. Lambert

"Amok Ltd./Cluff Mining operates a uranium mine at Cluff Lake in northern Saskatchewan. The project consists of one open pit and one underground mining operation along with a full-scale milling installation.The underground stoping operations are of the narrow vein type and are done between two levels 50 m apart. The mining method is undercut with concrete backfilling. Cuts are 3.5 m in height and can be as narrow as 1.4 m in width.Stoping operations are mechanized utilizing a CT-500E electric Microscoop marketed in Canada by Teledyne. The machine is only 85 cm in width and does all the mucking in stopes. Ore passes are provided in stope roughly every 40 m to 50 m.This paper describes the utilization of the CT-500E Microscoop in the company's underground operations and provides performance data related to the experience.IntroductionThe Amok Ltd ./Cluff Mining operation is located in the northwestern corner of Saskatchewan. The project started in 1980 with open pit mining and milling operations. In 1983, an underground mining operation began production . Today, the Amok Ltd./Cluff Mining installation produces 800 tonnes of uranium per year , which originates from both the open pit and the underground mine at about the same proportion."

Jan 1, 1990

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By J. Lui

Inco Copper Cliff Smelter commissioned two new Inco flash furnaces in 1991/1993 as part of its S02 abatement program. Each flash furnace is equipped with a fluid bed dryer. The ~ 12 wt% water content in the concentrate filter cake, flux, reverts and sludge is removed in the fluid bed dryer. The dry solids are discharged from the dryer together with exhaust gases into the baghouses where they are separated. The dry solids are transferred to four storage bins. In September 2003, for the first time since startup in 1991/1993, a large amount of elemental sulfur accumulation was discovered on the walls, roofs and floors of the outlet side of the baghouse chambers. Several baghouse fires were experienced during cleaning and conducting maintenance work in the elemental sulfur contaminated baghouses. Laboratory scale test work at the Inco research lab was conducted to understand the mechanism. A plant solution to minimize elemental sulfur formation was implemented with success. This paper summarizes the efforts to understand and minimize elemental sulfur formation in the baghouse chambers.

Jan 1, 2007

By T. W. Wlodek

"AbstractIn this paper a new type of durable 'spiral-rolled' drill set is introduced and its performance discussed. Efficient and economical mine drilling-depends to a great extent on durability of the drill-set employed. Premature failure of this element damages the drill bit and is costly when tungsten carbide bits are used.Time of drilling of 'spiral-rolled' drill sets introduced at present in Canada is considerably larger than for the presently used drill steel, but laboratory simulated service tests and practical field tests show that the 'drilling life' of the spiral-rolled drill set is several times that of ordinary drill steel.Some features of differential plastic deformation and differential surface rolling, so called 'spiral-rolling', are given.Relations between the drilling machine drill set and characteristics of the ore are discussed. The effect of shims on conical drill rod attachments, the mechanism of failure of drill steel, .and stresses during mine drilling, are analysed.IntroductionIN MINE DRILLING operations, the main interests are: the drilling machines as a source of working energy, the drill set as the tool transferring the working energy to the cutting edges of the bit, and, finally, the drilling characteristic of the .ore or waste rock.This paper includes a review of the possibilities of metallurgical and mechanical improvements in the drill set, with particular attention to drill steel and the attachments.For economical and efficient mine drilling operations, a durable drill rod, attachment, and drill bit are essential. Premature failure of any of these parts interferes with mining operations and is costly."

Jan 1, 1955

By L O. Montpetit

The economics of the asbestos mining industry of Canada, and the physical and chemical characteristics of asbestos fibre, as well as exploration, mining, milling and quality control methods, have been described by several authors in the past few years. The scope of this presentation is to survey the application of asbestos fibres in the major product groups of the construction industry in North America. Principal categories considered include flooring materials, asbestos-cement pipes and building products, high-temperature insulation, textiles, saturated asbestos felts and asphalt com pounds. During 1962, the asbestos mining industry of Canada produced an estimated 1.3 million tons of chrysotile fibre grades, and production capacity is expanding. The market demand for chrysotile fibre, on this continent, has been in the order of 50 per cent of the production volume. The asbestos industry is dependent for growth on the construction industry. Product research is active in finding new uses for asbestos fibre; some of the new developments are presented, including the use of short-fibre asbestos grades for extending the life of asphalt pavement.

Jan 1, 1963

By Peter A. Hacquebard

"The early history of the Geological Survey of Canada is closely connected with coal geology investigations in the Atlantic Provinces. In 1843, Sir William Logan, the first director of the Geological Survey, measured the 4441m thick shore section at Joggins in Nova Scotia. Detailed mapping of the coalfields were subsequently carried out by H. Fletcher during the latter part of the nineteenth and first part of the present century. During the 1920-1940 period, the stratigraphy of the carboniferous WIZS' established by WA. Bell, who later also became a diretor of the Survey. Bell's work WIZS' followed by coal geology investigations of A.A. Hayes, W.S. Dyer, EA. Goranson, G. W.H. Norman, J.E. Muller, T.B. Haites and P.A. Hacquebord.The activities and accomplishments of the Survey geologists during the past 150 years are presented in this paper.General Outline of Survey Activities in Coal Geology During the Past 150 YearsIn 1842, when the Geological Survey of Canada (GSC) was established, the industrialization of the major countries of Western Europe and North America was actively persued. The energy required for this industrialization was obtained from the only fossil fuel then available, namely coal. The measure of a country's major mineral wealth at that time was the availability of mineable resources of coal. Eastern Canada, where mining had been carried out since 1720, was known to be well endowed with valuable coal deposits. In the major fields of Nova Scotia (Fig. I) several large-scale operations had been started during the middle and latter part of the nineteenth century.The significance of coal, therefore, was well understood, and exploration surveys specifically oriented toward coal were carried out by the Geological Survey from its earliest beginning. The first report of a detailed geological description of the coal measures of eastern Canada was prepared in 1843 by Sir William Logan (1845), the founder and first director of the Geological Survey of Canada. This early work was continued and complemented in 1896 by H. fletcher (1906), who during the latter part of the nineteenth century and first part of the present century systematically mapped the coal-bearing regions of Nova Scotia, which he considered all to be of approximately the same age."

Jan 1, 1992