Search Documents

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By I. G. L. Sinclair

"ABSTRACTTill geochemistry was the principal exploration tool employed by Selco in the investigation of a zinc prospect in Lanark Township, Ontario. The geochemical studies were undertaken after the discovery at surface of marble boulders containing bands of sphalerite and lesser amounts of galena.The source of these mineralized boulders was sought by means of B-horizon soil geochemistry, followed, where appropriate, by back-hoe trenching and till sampling. The thickness of the tiff in this part of Ontario seldom exceeds 3 m or 4 m and it was generally possible to sample complete profiles of the till and thus to obtain detailed information concerning the dispersion of zinc. Drilling and trenching at the up-ice extremity of the zinc dispersion trains showed the source of the float to be sub-economic bands of sphalerite in the Grenville marble. IntroductionTill geochemistry was used extensively by Selco during the period 1975 through 1980. It was the principal exploration technique employed in a program seeking carbonate-hosted lead-zinc deposits of the Balmat-Edwards type in the Grenville rocks of southeastern Ontario. This paper describes the use of the method to locate the bedrock source of a group of sphalerite boulders found at the surface near the village of Hopetown in Lanark Township (Fig. I) . Geochemical investigations at this locality were the subject of a previous publication by the author (Sinclair, 1979).All of the analytical work related to this project was done by Bondar-Clegg & Co. Ltd. in their Ottawa laboratory. In all cases the -80 mesh fraction of the till was analyzed. The total zinc content was determined by atomic ab sorption spectrometry after hot aqua regia digestion; readily extractable zinc was determined by atomic absorption after samples had been cold-leached for 18 hours in an ammonium citrate hydroxylamine hydrochloride solution, the pH of which was adjusted to 8.5"

Jan 1, 1986

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab's Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By N. Tassé

Les substrats organiques sont à la base des biofiltres utilisant la réduction des sulfates pour générer de l&apos;alcalinité et diminuer la concentration des métaux dans des effluents contaminés. Afin de tester l&apos;efficacité de résidus forestiers utilisés dans de tels contextes, cinq types d&apos;écorce de nature et d&apos;âge variables ont été placés dans des contenants hermétiques et mis en présence d&apos;une solution synthétique de drainage minier acide. Le pH, l&apos;alcalinité et les concentrations de Fe2+ et SO4 2- ont été mesurés à intervalles réguliers pendant 70 jours. L&apos;importance d&apos;un éventuel neutralisant minéral et du type de souches de bactéries sulfato-réductrices pour l&apos;initiation et l&apos;évolution des réactions d&apos;oxydo-réduction ont été évalués en utilisant de la dolomite ainsi que des inocula de sédiments portuaires réducteurs et de boues d&apos;usine d&apos;épuration. Une augmentation de pH et des diminutions de Fe2+ et SO4 2- ont été notées dans tous les réacteurs. En l&apos;absence de dolomite, le pH augmentait de 1.6 à 5-6, Fe2+ diminuait de 400 à moins de 5-100 mg/L, et SO4 2- diminuait de 2500 à 750-1250 mg/L. Les échantillons inoculés avec des sédiments s&apos;avéraient légèrement plus performants que ceux avec boues. En présence de dolomite, le pH atteignait 6.5-7.0, et Fe2+ et SO4 2- tombaient à <5 et 20-40 mg/L, respectivement. Le degré de réactivité des résidus forestiers n&apos;était pas une simple fonction inverse de leur âge. Les échantillons ayant le mieux réagi, bien que parmi les plus vieux testés (années 1980), étaient ceux contenant une proportion significative d&apos;écorces de feuillus et peu de bran de scie. Les échantillons avec des proportions élevées d&apos;écorce de conifères ou de bran de scie étaient associés à des taux de réduction moindre. Nonobstant l&apos;amélioration rapide des conditions obtenue avec la dolomite, grâce à une neutralisation initiale plus prompte, il s&apos;avère que le type de résidus forestiers éventuellement utilisé dans une barrière réactive est de première importance pour l&apos;efficacité des mécanismes de réduction. Un système basé sur l&apos;utilisation de résidus forestiers devrait utiliser des écorces (plutôt que du bois) provenant de feuillus (plutôt que de conifères).

Nov 1, 2002

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By J. Dubinski

Poland is the ninth largest coal producer in the world and Coal Company is the largest Polish producer of this deposit yielding 51% of national production. Coal Company mines are located in the Upper Silesian Coal Basin. These are underground mines which operate in difficult geological conditions at great depths of up to 1200 m. One of the most common natural hazards in Polish mines are rockburst and seismic hazard impacting on surface infrastructure and habitants. In the assessment of the rockburst and seismic hazard methods of mining seismology play a leading role. This paper presents progress that was achieved in the last few years in the implementation of new seismic monitoring systems and seismic interpretation methods for the prevention of hazard deriving from seismicity induced by mining. This progress in assessment of rockburst hazard and impact of seismic activity on the surface infrastructure was achieved through close cooperation between the Coal Company and Central Mining Institute ? the country?s leading scientific institute in the field of mining seismology. New theoretical solutions are in the process of testing in mines of Coal Company where seismic monitoring systems are installed and controlled by well-qualified personnel. Some directions of further joint actions to increase the effectiveness of rockburst and seismic hazard assessment are presented as well.

Aug 1, 2013

By S. G. Coultis

Turner Valley is in the foothills of the Rocky mountains, at an altitude of 4,000 feet, and is 42 miles south west of Calgary. The present producing area is 8 miles long by 1 1/2 miles wide, while drilling is being carried on over an area of 10 miles by 2 miles . There are 32 wells producing, 26 wells drilling, and 17 wells shut down, making a total of 75 wells, which range in depth from 2,160 feet to 5,900 feet, varying according toa the well location on the anticline centre wells being shallower than those located on the flank. The first indication of possible production in this field was a gas seepage on the banks of Sheep river, in what is now the Royalite plant yard (Figure 1). Geologically, this seepage proved to be located on an anticline running through the valley in a southwesterly direction. The Calgary Petroleum Products Company was formed in 1912, and under the direction of Mr. A. W. Dingman, President, and associates, the first well was drilled. Production was obtained in this well. Gas was found in several horizons from 884 feet to 3,960 feet, and oil at 1,557, 2,718 and 3,839 feet. In May, 1914, oil was struck at a depth of 3,839 feet, this being a light straw-coloured oil of 60 gravity, which was blown spraying from the well accompanied by three to four million feet of gas. The latter contained some 200 grains of hydrogen sulphide per 100 cu. ft., giving it the disagreeable odour so well known in Turner Valley gas. This strike caused considerable excitement and started the famous 1914 boom, when some 400 oil companies were formed. The well referred to produced from two to five barrels of 60 gravity oil per day, and 4,000,000 cu. ft. of gas. The oil was used in the crude form in cars and trucks.

Jan 1, 1929

By Richard Murphy

"The general geology of the Great Bear Lake area has been described by; D. F. Kidd in the Summary Report of the Geological Survey for 1932. A brief description of the Eldorado mine was prepared by C. S. Lord for Memoir 230; Mineral Industry of the Northwest Territories; published by the Geological Survey in 1941. Recently; a detailed geological examination of the mine area has been initiated by the Geological Survey and; under A. W. Jolliffe's leadershif; J. D. Bateman; H. B. Thurber; and M. Feniak have prepared a number of maps and reports; as yet unpublished. Detailed mapping of the mine has been carried out since August; 1943; by A. W. Esty.Kidd has shown that, in the largely granitic country along the east side of Great Bear lake, the Echo Bay district is one of several underlain by older rocks . These he has divided into the Echo Bay and Cameron Bay groups. The former are strongly altered sediments, .porphyries, and lavas; the latter and younger group is predominantly sedimentary and far less altered. Associated with the granite, which everywhere intrudes the sediments and volcanics, are earlier differentiates. Later than all these rocks are various basic intrusives, collectively termed diabase. All the rocks are of Precambrian age."

Jan 1, 1954

By M. Mohammadi Zahrani

The morphological modification of primary and eutectic Mg2Si phases by bismuth (Bi) addition in Mg-5wt.% Si in-situ composite was investigated. It was found that with addition of 0.5wt.% Bi, the morphology of primary Mg2Si precipitates was altered from coarse dendritic to polygonal shape, and their mean size was significantly decreased from more than 20 µm to about 8 µm. Moreover, the rod-like eutectic Mg2Si in Bi modified Mg-Si alloy solidified much finer than that of the base alloy. Such improved microstructure of the modified alloy resulted in 10% tensile strength and 20% elongation improvement. The isotropic growth manner of primary Mg2Si particles in modified alloy was attributed to the poisoning of growth in preferred directions by dissolving Bi atoms in Mg2Si lattice. The reduction in size of eutectic Mg2Si was found to be the result of Mg3Bi2 compound formation around eutectic Mg2Si rods.

Oct 1, 2011

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By L. A. Melis, K. S. Fraser

"This paper describes the development of a milling circuit for the complex Midwest orebody, containing a high-arsenic uranium ore typical of that found in northern Saskatchewan. The results of preliminary bench-scale test work are summarized. Data from a pilot-plant program carried out at the Ontario Research Foundation are provided for the selected mill flowsheet. Also described are waste circuits which have been established to produce effluents of acceptable quality. Pilot-plant testing of sub-aerial tailings deposition is also described. The applicability of manufacturers&apos; equipment for the various circuits in the flowsheet is discussed.IntroductionThe Midwest uranium deposit is in northern Saskatchewan, 700 km north of Saskatoon, near the eastern edge of the Athabasca BasinDevelopment work on the project is directed by Canada Wide Mines Ltd., a subsidiary of Esso Resources Canada Limited. Participants in the project are Esso Resources Canada Limited, Numac Oil and Gas Ltd., Bow Valley Industries Ltd ., Mink Mining Corporation and Midwest Mining Corporation.The deposit consists of a series of flat lenses of massive ore overlain by a halo of lower-grade sandstone ore. The massive ore is formed of pitchblende and nickel arsenides, along with clay, and averages about 10% U and 9% Ni, The principal minerals are pitchblende (UO2-UO3), coffinite (U(SiO4)1-x(OH)4x), gersdorffite (NiAsS), niccolite (NiAs) and rammelsbergite (NiAs2). The sandstone ore, a friable clay-rich sandstone with sooty pitchblende, averages about 0.4% U and 0.6% Ni. Typical expected mill feed analyses are given in Table I.A bench-scale development program ore was carried out during the period from August 1978 to May 1981 in the laboratories of Lakefield Research of Canada Ltd. (Lakefield), (Lakefield, Ontario), the Colorado School of Mines Research Institute (CSMRI), (Golden, Colorado) and, to a lesser extent, the Ontario Research Foundation (ORF), (Mississauga, Ontario) and the Saskatchewan Research Council (SRC), (Saskatoon, Saskatchewan). Direction of the development studies was shared by Canada Wide Mines Ltd. and its metallurgical consultants, A.H. Ross and Associates. Input was received from Envirotech, Enviroclear, Interox America, and Knight and Piesold Ltd."

Jan 1, 1983

By A. Aftabi

To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples areanomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb(>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2in the southern part of the area. The strong Cu-Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry cop-per mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sul?de mineralization is present.

Jan 1, 1997

By A. Aftabi

Abstract-To evaluate geochemical aspects of sheared zones, 35 samples of granitoid rocks from an area of shearing >5 km2 at Derehamzeh, Iran were studied geochemically. Relatively unaltered samples within the shear-zone area average 38 ppm Cu, 1.45 ppm Mo, 4.6 ppb Au, 0.21 ppm Ag, <1 ppm Re, 46 ppm Zn, 28.5 ppm Pb, and 0.34% S. Bleached, hydrothermally-altered samples are anomalous in Cu (>896 ppm), Au(>59.5 ppb), Ag(>24.4 ppm), Re(>1.28 ppm), Zn (>164 ppm), Pb (>218 ppm), and S(>0.9%). Some samples from bleached sheared zones that are highly anomalous in Cu (5000 ppm), Mo(23 ppm), Ag(74 ppm), and Au(200 ppb) are characterized by a typical sericitic alteration assemblage consisting of sericite, pyrite, chalcopyrite, and granular quartz. The main anomalous zone extends over about 0.4 km2 in the southern part of the area. The strong Cu- Mo-Au-Ag association in the sericitic shear zones suggests a possible relationship to porphyry copper mineralization, similar to that found in northern Chile. Further studies on drill-core samples in the southern sericitized shear zones are required to determine if more extensive porphyry-type sulfide mineralization is present.

Jan 1, 1997

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By J. O. G. Posada

Magnesium derived foams were prepared by using the so-called baking of powder blended precursor material method. This method comprises mixing magnesium powder with a small fraction of blowing agent (ZrH2, Cs2CO3 and CaH2) and Ni like catalyst, compacting this mix and creating a foam by heat treatment above the magnesium melting temperature. The resulting samples were characterised by microscopy, gas adsorption (BET method) and by small angle neutron scattering. Several mathematical models were used in order to determine particle size distribution, fractal dimension and total pore volume fractions.

Jan 1, 2005

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016