Search Documents

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By S. Sopher, C. Barsotti

"Inco Gold Company was created in 1987 as an unincorporated business unit of Inco Limited. In 1988, Inco Gold Management Inc. was incorporated to supply management, exploration and engineering services to this unit. The first new project, at Casa Berardi, Quebec, was brought to production in September 1988, less than two years after completion of exploration. For 1989, Inco Gold's exploration and capital expenditures have been budgeted at approximately $94 million, a record level. Inco Gold holds interests in more than 80 precious metals ventures and prospects in Canada, the United States, Brazil, Indonesia, Papua New Guinea and France. The most advanced projects, in addition to Casa Berardi, are at Mineral Hill, Jardine, Montana, where initial production is anticipated in the third quarter of1989, and Crixas in central Brazil, where production is scheduled to begin during the fourth quarter of the same year.BackgroundTraditionally, Inco Limited's mineral exploration has concentrated on nickel and other base metals but since the early 1980s Inco's exploration activity has focussed strongly on precious metals, principally gold. As a result, three deposits have been discovered and developed . In order to accelerate the establishment of a strong gold mining enterprise with its own specific growth and profit objectives, Inco Gold Company was created in 1987 as an unincorporated business unit. At the end of 1988 Inco Gold's share of drill-indicated gold reserves was approximately 14 million short tons containing 3.4 million ounces of gold.At Casa Berardi in northwestern Quebec, one mine is in production and another is planned to open in 1990. Properties at Crixas in Brazil and at Jardine, Montana, U.S.A., were being readied for production in 1989. By 1991, Inco Gold's share of gold production is expected to be 125 000 ounces with a target of 400 000 ounces annually by the mid-1990s."

Jan 1, 1990

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,' during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By P. D. S. St. Pierre

IN REGENT YEARS, blast furnace operators have found it necessary to improve their technology in order to handle increasingly low-grade feed and yet satisfy the demands for greater tonnages of metal. Studies have been made covering several aspects of the problem, and in this connection the slags produced in the iron-making process have been critically examined with a view to discovering the slag with the optimum properties for a given operation. A good slag should combine, as far as possible, the properties listed in Table I. Unfortunately, some of these desirable properties are incompatible. For example, the advantage of the small ?bulk of a low-flux slag is offset by its low desulphurization potential and high viscosity. Similarly, a very fluid slag increases refractory wear. It will be seen, then, that a balance must he struck between these conflicting requirements. In the .present paper only the melting relationships of blast furnace slag ?compositions will be considered in detail. In interpreting the data herein presented, the optimum property requirements listed in Table 1 must strictly be borne in mind. It should also be noted that the discussion presented here always relates to calcined fluxes, since this facilitates reference to the final slag composition. Thus, in making calculations pertaining to the ?burdening of the furnace, due allowance should ?be made for the fact that the fluxes are added as carbonates.

Jan 1, 1956

By Sergio Cattalanl, Francis Chartrand

"The geology and origins of volcanogenic massive sulfide (VMS) deposits in the Abitibi belt of northwestern Quebec have been the subject of discussion since the discovery of the Horne orebodies in Noranda in 1923.The present Noranda version of the VMS model characterizes the ideal deposit as a stratabound, base-metal accumulation that is in close spatial relationship with hydrothermal alteration and stockwork zones, felsic lava domes, coarse phreatic-pyroclastic breccias, and subvolcanic intrusions that characterize vent- and proximal{acies submarine volcanic environments. Deposits tend to occur in a favorable stratigraphic interval within a mining camp, and this is well-documented in the Rouyn-Noranda and Matagami camps.However, in recent years many VMS deposits have been shown to deviate from the ideal Noranda-type. For example, the Ansi/ deposit is characterized by sulphide-bearing alteration zones that extend far above the massive sulfide lenses, and by abundant magnetite immediately underlying massive sulfide. The Horne deposit appears to lack the typical chloritic alteration pipe underlying the massive sulfide lenses, as well as laterally-equivalent exhalite horizons. The Horne and Quemont deposits, besides being the two giants of the camp, are particularly rich in gold, whereas others, such as WaiteAmulet and Millenbach, have low gold values. Finally, some deposits in the Noranda camp, such as the Ansil, Corbet and Mobrun mines, are outside the favorable stratigraphic interval. Therefore, it would appear that part of the key to renewing base metal reserves in northwestern Quebec is the use of evolving descriptive-genetic models that incorporate geological variations like those cited above."

Jan 1, 1990

By J. R. Kadambi, J. Furlan, Kucukal E.

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV.INTRODUCTIONA hydrocyclone is a piece of equipment used to separate and/or classify solid particles or liquid droplets from liquid solid or liquid-liquid feed. Versatile in application, hydrocyclones have been widely used in industrial applications including the food, oil, power generation, chemical, and mineral processing industries. The first hydrocyclone was introduced in 1891 by Bretney to purify various liquids (Bretney, 1891). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2017

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960

By Peter M. Watt

The objective s of this paper are: (a ) to examine and discuss the burdens we place on our extractive industry; (b) to compare the levels of taxation in Canada with those in other countries; and ( c) to suggest certain broad parameters within which our taxation policies may be made more rational and stable. Among the burdens identified are taxation, the ownership and use of our resources, environmental issues and the rather emotional issue of so-called 'super profits'. Finally, the paper will address certain broad but key areas of policy which need attention and agreement if our tax system is to be made more rational. Such areas include: whether and if so why the extractive industry should be given incentives;. what circumstances, if any, justify a 'higher' than normal' level of taxation, and, ?if the concept of economic rents is a justifiable one, how might a basis for them be established which recognizes the fluctuating value of much of the industry's output. Note: The paper was written before the 1977 Federal and Provincial budgets were presented. Consequently, the paper does not reflect any changes proposed in these budgets.

Jan 1, 1977

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

ABSTRACT Based on mineralogical characteristics and processing techniques required, gold ores can be classified into 12 types: gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper-gold ores, porphyry copper-gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores, and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type differs and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ore and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2013

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By Tassos Grammatikopoulos, Vladimiros Papangelakis, Douglass Duffy, Cheryl Washer, Srinath Garg

Flotation operations in Sudbury, Ontario, seeking to separate pentlandite and chalcopyrite from mixed sulphide deposits, produce pyrrhotite tailings that have been disposed of in tailings ponds for over 50 years. These reactive tailings are viewed as waste, despite containing ~0.8 wt% Ni, and represent an environmental liability because of their acid mine drainage (AMD) potential. Given the large quantities of pyrrhotite currently stored in Sudbury, and declining ore grades elsewhere, these tailings have shifted from being viewed as a waste to a potential resource. Recent advances in the bioleaching of low-grade sulphide ores have raised the prospect of bioleaching as a potential low-cost processing option. However optimization of this proposed process requires a thorough understanding of the mineralogy of the pyrrhotite tailings that would be leached. The work presented here addresses the characterization of two distinct Sudbury pyrrhotite tailings, namely from the Vale and Glencore operations, using electron microprobe, XRD and QEMSCAN analysis. Particular focus is given to how the mineralogy may affect bioleaching as a processing option, through the deportment of nickel and the various phases present

Jan 1, 2015