Search Documents

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By E. Johansson, T. Siren, K. Kemppainen

"As part of the preparations for the design of an underground repository for radioactive waste at Posiva’s Olkiluoto site on the west coast of Finland, there has been considerable site investigation work. Except the extensive surface based investigations, Posiva started in 2004 the construction of an underground characterisation facility termed the ‘ONKALO’. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. The research conducted in the ONKALO gives further information on the bedrock and groundwater conditions of the final disposal site, as well as on the impact of the construction. The ONKALO provides an excellent opportunity to investigate the rock at tunnel scale, to conduct in-situ testing in rock, to develop excavation and final disposal techniques in realistic conditions. The ONKALO has aided in collecting the data needed, supported by a Preliminary Safety Assessment, for the application of the construction license that was submitted in the end of 2012. The target is to begin disposal operations in 2022. According to current plans, the final disposal would end in 2112 and the repository would be sealed up by 2120. The testing in the ONKALO still continues several years. This paper presents the current characterisation and research activities in the ONKALO. INTRODUCTIONAfter the Finnish Government's favourable policy decision in 2001, Posiva Oy, which is an expert organisation responsible for the final disposal of spent nuclear fuel of the owners in Finland, has focused further investigations at the Olkiluoto site, western Finland (Figure 1) and has started in 2004 the construction of an underground facility termed the ‘ONKALO’. The ONKALO is not a nuclear waste repository, but more than just an underground research laboratory URL – it is an underground rock characterisation facility. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. In addition to facilitating bedrock research, the ONKALO also provides an opportunity to develop excavation techniques and final disposal techniques in realistic conditions. Later, the ONKALO facilities can be put into use when building and using the repository. The construction methods and materials have been selected in order not to jeopardise the long-term safety of the repository site. The findings of the ONKALO and other investigations will provide the knowledge needed for an application, supported by a Preliminary Safety Assessment, to construct a final repository for spent nuclear fuel at the site. Posiva has submitted an application for the construction licence for a disposal facility in the end of 2012. The target is to begin disposal operations in 2022 and the repository would be sealed up by 2120."

Jan 1, 2015

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By A. M. Christie

Acknowledgements The following account has been compiled mainly from records and maps of Eldorado Mining and Refining (1944), Limited, hereinafter called the Crown Company. This work was done under the supervision first of R. F. Murphy, Chief Geologist, and later of E. B. Gillanders, Eldorado Mine Manager and Manager of Eldorado Exploration Division. W. F. James and B. S. W. Buffam are consulting geologists. Since 1946, S. N. Kesten has supervised geological work for the Company in the Goldfields area. Where maps of Eldorado properties have been included in this paper, the name of the geologist who examined the property is acknowledged on the map. Outline of General Geology The geology of the area is described in the Goldfields and Martin Lake preliminary maps of the Geological Survey and accompanying Paper 49-17. In brief, the Tazin series of Precambrian age, consisting mainly of sediments with minor interbedded volcanics and basic intrusives, is intruded and replaced by granite, now generally gneissic. The late-Precambrian Athabaska series of conglomerate and arkose, with interbedded basalt and andesite flows, rests unconformably on the older rocks. All these rocks are cut by small diabase dykes. The geological terms used in this paper and in the accompanying figures are standard with the exception of the term 'mafic rocks'. These include all the basic or dark coloured rocks of the Tazin group, such as amphibolites, biotite schists, and chlorite-epidote rocks (greenstones), whether they be of extrusive, intrusive, or sedimentary origin.

Jan 1, 1949

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

By J. E. Moyle

The costs of labour and electric power are of prime concern to almost all industrial enterprises, and various methods of reducing their impact on production costs are constantly being developed. Automation is one of these schemes, and has received a good deal of attention in the past few years. In the mining industry, compressed air is almost universally used, and its cost is significant. Although the compressor machinery now in use has achieved a high degree of development, the hazard of explosion and fire still exists in these systems. There is thus considerable resistance in some quarters to suggestions that such installations can be safely and successfully automated. The Milliken power plant consists of two 30,000 lb. /hr. fully equipped high-pressure boilers, four H.P. air compressors, a steam turbine for stand-by power, and several L.P. compressors and vacuum pumps. With the installation of automatic and protective equipment in the machinery section, the shift force has been reduced from three to two men.

Jan 1, 1963

By J. B. Boisvert, D. S. Silva

"Drillhole placement involves benefits, costs, and constraints. Benefits are related to the drilling campaign value, which includes maximizing “indicated” and “measured” resources. Costs include drilling, rig movement, and access construction. Constraints include infeasible areas, maximum and minimum angles of drilling, maximum depth of drilling, and budget. Manually planning drillholes that meet these constraints is suboptimal. A framework for straight drillhole optimization that accounts for benefits, costs, and constraints is presented. The method aims to maximize the value of resources converted from “inferred” to indicated and measured. The framework is demonstrated for a Nevada gold deposit and outperforms manually selected drillholes.RÉSUMÉ Le choix de l’emplacement d’un trou de forage s’accompagne d’avantages, de coûts et de contraintes. Les avantages sont liés à la valeur d’une campagne de forage, qui comprend l’optimisation des ressources « indiquées » et « mesurées ». Les coûts englobent le forage, le déplacement de l’appareil de forage et la construction des routes d’accès. Quant aux contraintes, elles portent sur les zones impraticables, les angles maximums et minimums de forage, la profondeur maximale de forage ainsi que le budget. La planification manuelle des trous de forage répondant à ces contraintes est sous-optimale. Cet article présente un cadre relatif à l’optimisation des trous verticaux de forage tenant compte des avantages, des coûts et des contraintes. Cette méthode vise à optimiser la valeur des ressources converties de la phase « ressources présumées » à celle de « ressources indiquées et mesurées ». Ce cadre est appliqué à un gisement aurifère du Nevada et donne de meilleurs résultats que les trous de forage sélectionnés manuellement. INTRODUCTIONDetermining the optimum location of infill drilling has been studied because the high cost of drilling suggests that using fewer drillholes is preferred, and targeting locations of the deposit that are locally uncertain should result in better mine planning decisions and increased profit of the operation. Existing methods for optimizing drillhole locations consider minimizing the kriging variance (KV) as the objective and are mostly restricted to two dimensions (Soltani-Mohammadi & Hezarkhari, 2013a, b; Soltani- Mohammadi, Safa, & Mokhtari, 2016)."

Jan 1, 2018

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By Patrice Nadeau, Yuejun Zhang, Dan Chen, Liming Huang, Claude Gagnon

"The traditional Denver flotation cell is generally suitable to process material ranging approximately from 5 µm to 300 µm. For floating over 300 µm material, its efficiency is significantly getting lower mainly due to the difficulty to suspend coarse particles uniformly, which decreases the chances of particles to attach to bubbles and increases the chances of detachment.RTFT (Rio Tinto Fer et Titane) owns one of the world’s largest hemo-ilmenite deposits. Considering the whole processing technology, the ore is only crushed to -1180 µm. The crushed ore contains about 0.32% S and most of the sulfur is removed by rotary kilns in the ore preparation plant. In order to achieve a similar S reduction, without emitting SO2 into the air, an alternative technology by flotation was pursued.Laboratory and pilot scale-up tests showed that traditional Denver flotation cell could perfectly remove the sulfur from the material sizing 0-300 µm. For the coarser particle sizes, two different models of equipment were tested to improve flotation efficiency: HF (HydroFloat Separator) from Eriez and CLF from BGRIMM (Beijing General Research Institute of Mining and Metallurgy), China. The D6” HF, which is a device that combines flotation and gravity separation, demonstrated its ability to recover those very coarse particles. As compared to the Denver flotation cell, the modified 25 L CLF coarse particle flotation cell achieved better results at higher pulp solids percentage and with a shorter flowsheet."

Jan 1, 2016

By S. Kline

The compositions of metamorphic minerals of the south limb of the Dore Lake Complex have been determined by microprobe techniques. Mineral assemblages typical of the greenschist facies occur in Mg-rich bulk compositions, but in Fe-rich rocks albite-epidote amphiboli te facies assemblages occur. Low oxygen fugaci ties and a general paucity of metamorphic fluids prevailed in most of the complex, but a higher oxygen fugacity is indicated near the Chibougamau Pluton, and a local abundance of C0z and Cl in fluids near the pluton is suggested by the presence of scapoli te. The metamorphic gradient overprinted on the complex near the Grenville Front is apparent in mineral chemistries as well as by the appearance of garnet. Chlorite becomes richer in Mg, and iron is fractionated more strongly into hornblende. The amphibole also increases in Alz03.

Jan 1, 1984

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

By S. Kariyawasam, R. McNealy

Pipelines are subject to multiple threats often requiring quantification of pipeline risk and engineering evaluation of in-line inspection and other data to effect discovery of conditions defined by the regulation. Public concern and pressure from regulatory bodies are accelerating the need for pipeline operators to formalize and intensify their approach to integrity management. Most operators need a phased approach to progressively adopt the most relevant and needed assessments. The organized and relevant assessment steps need to be introduced according to data available and maturity of the integrity management program. Each refinement to the quantification offers distinct advantages to the user. In this paper, the progressive integrity assessment solutions using quantitative methods are presented. Methodologies for engineering evaluation of integrity in-line inspection data for immediate and future integrity are summarized. Corrosion is used as an example, but the approach is applicable to any time-dependent defect based hazard. Strategies for pipeline integrity management are discussed.

Jan 1, 2005

By Elaine R. Goetz

The eastern and southeastern regions of Ohio are part of Appalachian coal country, with a documented 1,300 miles of streams impacted by acid mine drainage. Since 1995, partnerships of local watershed groups, government agencies, private industries and universities have focused on the remediation of the affected waterways. The partnerships have spent $2.4 million annually in constructing and operating treatment systems such as wetlands, anoxic limestone drains, successive alkalinity production systems, steel slag leach beds, and lime dosers. These systems have been partially successful, and water quality has improved in the region, but no treatment has yet met the ultimate objectives of low cost, continual remediation. Our research group has investigated an alternative system for acid mine drainage treatment: electrolysis combined with pH adjustment to selectively precipitate recoverable, saleable metal products to offset the cost of treatment. We utilized a $0.2 million pilot facility constructed by the Wayne National Forest, in Nelsonville, Ohio, to process approximately 40 L/min of mine drainage from surrounding seeps. The pilot facility has multipurpose tanks that can be adapted to process acid mine drainage with different characteristics, such as high or low aluminum content or high or low carbonate concentrations. Sodium hydroxide was used for pH adjustment. Results indicate that saleable product can be generated with this treatment technology. In an initial, not optimized trial, one seep yielded 4.7 kg of dried 69 % iron oxide product from 10 hours of pilot facility operation, treating 23,000 L with electricity costs of $4.68. Dissolved iron concentrations in the water were reduced from 242 ± 18 mg/L to 2.8 ± 2.0 mg/L (99.0 % removal) while the initial acidity of 443 mg/L as CaCO3 was neutralized to an alkalinity of 160 mg/L as CaCO3. Iron oxide can be sold as pigment for an average of $1.47 per kg in the United States. Currently, approximately 80 % of all pigment used in the United States is imported, and there is incentive to purchase domestically recovered pigment. If the iron oxide from the pilot facility could be sold as pigment for $1.47 per kg, 43 % of the operating cost (raw materials, electricity and construction costs) of treatment could be offset by the sale of the product. Considering the cost offset, the electrolysis process shows potential as a sustainable low cost alternative for treating acid mine drainage.

Aug 1, 2013

By D. R. Pyke

Many of the gold deposits in the Timmins• area show a close spatial association to ultramafic metavolcanics. Available analytical data suggest that ultramafic rocks contain significantly higher gold contents than other major rock types. In addition, recent analyses by Keays (1975) suggest that talc-carbonate alteration of ultramafic rocks releases significant quantities of gold. It is proposed that the ultramafic volcanics formed the principal source of gold for the deposits in Timmins, and that the gold was derived from the ultramafic flows when they were extensively carbonatized. Carbonatization of the ultramafic rocks and emplacement of the auriferous quartz-carbonate veins was probably coincident with the last major period of deformation in the gold camp. Delineation of hitherto unrecognized ultramafic volcanics could be an important guide to the discovery of further gold deposits.

Jan 1, 1976

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011