Search Documents

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By K. Hasselwander, K. Knabel

"A significant area of Outotec’s business involves fluidized bed roasting. With several decades of experience, more than 300 reference plants and strong R&D capabilities, the company provides several industries with optimum processing solutions. Applications include oxidation and sulfation of sulfides found in copper, pyrite and zinc concentrates. Gold production and de-arsenifying roasting are also within this scope. This paper describes the latest furnace developments and includes novel trends. Moreover, hot and wet gas cleaning systems are examined focusing on unit operations related to the removal of components such as dust, SO2 for sulfuric acid production, fumes, halides, Hg, hydrocarbons, nitrous oxides and metals.INTRODUCTIONGenerally, when defining roasting processes, it can be stated that the respective primary pyrometallurgical reaction is exothermic, of gas-solid nature and relates to a value solid product. These processes are a key focus within Outotec’s scope and include: (i) dead roasting (ii) sulfating roasting (iii) partial de-arsenifying roasting and (iv) two-stage, de-arsenifying roasting.Dead roasting involves the oxidation of a given sulfide, thus allowing for a subsequent leaching process, and has been applied to producing ZnO. Dead roasting of pyrite has also been extensively utilized with a primary goal of producing sulfuric acid. In contrast, sulfating roasting involves converting a sulfide to its sulfate, enabling a selective sulfation of components, such as Cu or Co, and their separation from ferrous components during leaching (produced sulfates are soluble). Partial roasting involves partially oxidating the metal sulfide to its oxide with the simultaneous production of gaseous As4O6, which is handled during gas cleaning. The solid product, containing hardly any As, is rich in S and can be fed to a respective smelter (e.g. in the case of Cu). Alternatively, if the production of oxide is required, a dead roasting step is added after the partial roasting step, with the overall process considered as two-stage roasting."

Jan 1, 2012

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By Guojun Wang, Zejun Chen, Wenchang Liu

Al/Mg/Ti laminated metal composite sheet (LMCS) can combine the merits of each of metal components, and obtain excellent performances. It incorporates the advantages of high strength, light weight, easy melt and atomization, and good space adaptability to substitute for the bumper Al sheet of Whipple shield structure for space debris shield. The Al/Mg/Ti LMCS was fabricated by hot roll bonding technology in a certain sequence. The manufacturing process and parameters were analyzed and studied, including the first rolling reduction, roll boding temperature and stacking structure of each metal. The microstructure of dissimilar metals and bonding interface were characterized and analyzed. The optimized manufacturing procedures and parameters were presented based on the microstructure and mechanical properties of LMCS. The research results offer some guides and references for controlling the shape of bonding interface, optimizing the annealing process, improving the mechanical properties of Al/Mg/Ti LMCS.

Jan 1, 2015

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By Derek V. Ellis, Jack L. Littlepage

"Marine ecosystem effects ar1smg from the discharge of man-generated wastes to the sea can be schematized as: acute poisoning, chronic poisoning, enrichment, suffocation, temperature effects, salinity effects, toxin bio-concentration, changed production rates and changed species equilibria. A professionally designed site-specific monitoring program to check for such effects can not only safeguard the marine ecosystem from degradation, but it can also protect the industry involved from unanticipated remedial action after expensive construction has been undertaken. Monitoring programs should consist of three steps. Step 1 is an ecosystem survey which should be undertaken prior to final design of the discharge system and submission of applications for permission to discharge, because there can be considerable cost savings in obtaining information at an early stage in development. Step 2 involves location of the effluent field at the time of starting discharge, and analysing its dispersal behaviour. Step 3 consists of ecosystem monitoring with sampling stations and specific tests based on the accumulated prior information."

Jan 1, 1972

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By P. Kordi, L. Egorova, R. J. Bowell, D. Gurevich, V. Sedov, A. Mikhailov, D. A. Holwell

ABSTRACT Reconnaissance exploration in the Kuene region Namibia has included geological mapping, soil and stream sediment geochemistry, and ground geophysical methods. Copper mineralization occurs within a well-defined belt with north-northwest to south-southeast trend, parallel to the regional strike of the sedimentary rocks. The occurrences vary in size but are generally stratabound. The mineralization is centred on the transition from calcareous shale and interbedded limestone, through carbonate rocks, to quartzite. Geochemical anomalies have been identified correlating to induced polarization (IP) and magnetic anomalies. The anomalies identify one potential metallogenic zone more than 17 km in strike length.

Jan 1, 2012

By Marcondes Lima Costa

The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes,and the younger ones on widespread hilly to ?at lowlands. Both types show complete or truncated pro?les, generally covered by deep yellow to brown topsoils. The mature laterite pro?les contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic pro?les. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature pro?les. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epi-genetic alteration types. The lateritic pro?les show a well-developed ore zonation which is related to speci?c lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold;and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire pro?les include titanium (as ilmenite andanatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly asilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic pro?les, has led to the formation of high-grade kaolin and refractory bauxites. The laterites inthe Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By Marcondes Lima Costa

Abstract-The Amazon region is characterized by the development of deep chemical weathering represented by widespread lateritic covers and soils. Two distinct periods of laterite formation can be distinguished: mature laterites from the Eocene-Oligocene (and locally from the end of the Cretaceous), and immature laterites from the Pleistocene. The older laterites occur on plateau landscapes, and the younger ones on widespread hilly to flat lowlands. Both types show complete or truncated profiles, generally covered by deep yellow to brown topsoils. The mature laterite profiles contain high concentrations of gibbsite and/or aluminum phosphate, whereas the immature ones are poor in these minerals. The Amazon region is rich in mineral deposits related to lateritic profiles. Some mineral deposits are of primary origin but were concentrated to economic grades by lateritic processes. The most important ore deposits are of iron, aluminum (bauxite), kaolin, manganese, gold, nickel, copper and phosphate. These are mainly related to mature profiles. The wide spectrum of ore deposits and mineralogical and geochemical complexity of the Amazon laterites has been promoted by: (1) the prevalence of ideal conditions for laterite formation throughout much of the Tertiary; (2) the presence of varied basement lithologies due to contrasting geological environments; and (3) a variety of epigenetic alteration types. The lateritic profiles show a well-developed ore zonation which is related to specific lateritic horizons. Iron and gold deposits occur in the ferruginous horizon, which is nearest the surface; the central aluminous horizon hosts bauxites, aluminum phosphate, strontium and gold; and the lower clayey horizon contains deposits of manganese, nickel, copper and kaolin. Resistate phases which residually accumulate throughout entire profiles include titanium (as ilmenite and anatase), chromium (as chromite), tin (as cassiterite), yttrium (as xenotime), and niobium (mainly as ilmenorutile). Epigenetic alteration, caused by swamp environments developed above truncated lateritic profiles, has led to the formation of high-grade kaolin and refractory bauxites. The laterites in the Amazon region contain most of all known kinds of ore mineralization related to laterite processes.

Jan 1, 1997

By L. M. Dwarkin, D. F. Coates

Crows Nest Industries Limited adopted roof bolting in 1963 to improve roof control and to extend continuous miner utilization in one mine. Bolting was held back because anchorage tests gave inconsistent results. The time lapse between mining and bolting was suspected as a cause, and so a test entry was driven and sections of it were bolted as part of the work cycle in addition to the normal timbering. This paper presents the results of the instrumentation of test entries and discusses the utilization of the data to improve mining procedure.

Jan 1, 1967

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By W E. vanSteenburgh

The Polar Continental Shelf Project was initiated in 1959 to provide an administrative and logistic vehicle for research in the physical sciences of the land, sea and channel area of the Arctic Archipelago. Most of the scientists are supplied on secondment from the professional branches of the Department. The yearly expeditions number some eighty scientists and sub-professional staff, and they are supported by a fleet of fixed-winged aircraft and helicopters. Accurate positioning is obtained by the use of a Decca Lambda navigational system which is moved as the area of interest is shifted. The Project is designed to accommodate not only physical scientists, but to provide facilities for other scientist who may have an interest in the area under study. The main research scope of the Project includes topographical surveys, hydrography, oceanography, geology, including marine sedimentary studies, gravity, magnetics, seismology, glaciology and geography. The Polar Continental Shelf Project was initiated and recommended by the Committee on Northern Development in 1958.

Jan 1, 1963

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012