Search Documents

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By G. M. Ritcey, V. M. McNamara

"In the processing of gold ores by the cyanidation route, effluents which are discharged to the tailings areas can contain up to several hundred parts per million of cyanide in complex combination with similar quantities of heavy metals. Complicating this obvious problem of waste control are concentrations of thiosalts and thiocyanates which are roughly equivalent to the amounts of cyanide species. Although most gold mills are located in thinly populated areas, such contaminants can represent a potential environmental problem due to the various limitations exhibited by on-property ponding.The former Extraction Metallurgy Division of CANMET recognized the problem and, in early 1974, invited representatives of the gold mills to Ottawa to discuss the situation. At that meeting members of the Division presented a ""state of the art"" literature survey of cyanide abatement technology for waste solutions, together with preliminary cost estimate data(1). Shortly thereafter, Environment Canada, together with Environment Ontario, decided upon a guideline of 0.1 ppm (0.1 mg/l) total cyanide content as tolerable for an effluent stream which is discharged, in any manner, to the watershed."

Jan 1, 1978

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By Charles Tkaczuk

Key issues ? Process control is a corporate function implemented locally. ? Security and documentation is mandatory requiring standard practices. ? Publish and communicate activities (do not re-invent the wheel). ? Payback metric system for all projects. ? Partnering with vendors based on experience, expertise and joint R&D. ? Focus on phased process control projects and distribution of costs. ? Integration of services and functions. ? Application of global standards. ? Big picture application thinking.

Apr 1, 2005

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By Thomas Clark

This report presents a review of the distribution and exploration potential of platinum-group elements (PGE) in Québec; it is based on published and unpublished analytical data. This qualitative evaluation of the PGE potential, whether in PGE-dominant deposits or in Ni-Cu-dominant deposits with co-product PGE, is based on interelement ratios such as Ni/Pd, Cu/Ir, Cu/Pt, and Cu/Pd. Good PGE targets, i.e., deposits associated with magmas fertile in PGE, are identified. Less favorable PGE targets, i.e., deposits associated with PGE-depleted magmas, are also mentioned. The importance of exploring for deposits similar to those at lac des Îles and East Bull Lake (Ontario) is emphasized.

May 1, 2001

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By A. Hussain

PAPER NOT SUBMITTED FOR PUBLICATION

Jan 1, 1987

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By L. Becze, B. Pierre, S. Di Carlo, G. P. Demopoulos

From January to June 2007, the autoclave production at the Kidd Metallurgical Site was severely affected as a result of plugged discharge lines and extensive precipitation/crystallization of sulphates that caused massive scaling in different autoclave compartments. Work was performed at McGill University to understand the root causes. The crystallization of zinc and ferrous sulphate salts was investigated in terms of solubility measurements. Scale samples were characterized using chemical and mineralogical-spectroscopic analysis. In this paper, following a description of the Kidd zinc pressure leach operation, highlights from this investigation are presented and solutions used to overcome the problem are outlined.

Jan 1, 2008

By E. Dernedde

A few studies have suggested that the rate of adsorption of hydrogen fluoride on smelter grade alumina is determined by kinetic factors. However, no performance equation for dry scrubbers has appeared in the literature so far. Experimental data from a pilot dry scrubber with co-current flow were compared with results of kinetic models of adsorption, film diffusion and pore diffusion. The pore diffusion model was deemed the most appropriate. It was transformed into a performance equation for steady-state operations of dry scrubbers by the inclusion of the alumina recirculation. Operating results of industrial dry scrubbers with co-current flow were successfully evaluated by means of the performance equation. The average fluoride content of the alumina was also estimated by using the pore diffusion model.

Jan 1, 2011

Who is ArcelorMittal Mines Canada ?One of Canada's leading suppliers of iron ore to steel markets around the world ?Past company name = ??Quebec Cartier Mining?? ?Operator of one of North America's largest open-pit mines ?Mont Wright Mines ?Fire Lake Mine ?Largest ArcelorMittal iron ore mining subsidiary ?Annual production of 15 million tonnes of concentrate ?Major expansion program to 24 MT/Y ?Internationally competitive pellet plant ?9.0 million tonnes annually

May 1, 2011

By Y. Luo

The rock breakage process in drilling is a main source of noise in roof bolting operations, especially when hard rocks are encountered. Proper control of drilling operation can provide an opportunity to improve energy efficiency of drilling and to reduce noise and heat generated from bit-rock friction. Drilling tests have been conducted in laboratory settings to confirm this noise-reduction strategy. Preliminary results show that the drilling parameters, penetration and rotational rates can be controlled to achieve in a desirable range in drilling medium hard rock. Based on the theoretical and experimental studies, rational drilling control strategy is developed for noise control while maintaining a safe and productive roof bolting operation. Applying this strategy in underground roof bolting operation, the noise exposure of roof bolter operators will be significantly reduced.

Aug 1, 2013

By Andreas Zielonka

To meet the increasing demands of the quality and long term stability of technical systems also the applied materials have to full fill higher standards. This is of special importance where the function of a whole system depends on the reliability of the used materials for example for connector systems in automotive, computer and other electronic equipment?s. In most cases for connector systems electro deposited top layers are applied. To improve the quality of the applied layers new electro deposited systems are developed. One important field of research are the development of composite materials as dispersion coatings and multilayer systems. Multilayers are systems with a high number of single inter-layers of different metals or alloys with the wide chance of the alloy composition. As gold is one of the most important contact material for high quality connector systems it is used as basis for the development of multilayer systems. For the electrodeposition of multilayers two different methods can be applied, the single and the dual plating process. As in the dual plating process two different electrolytes are used, the single plating process allows the formation of multilayers from one electrolyte. In the presented research results cobalt and nickel are used besides gold for the formation of the multilayers. The properties of the layers can be influenced in a wide range by the change of electrolyte composition and the process parameters as current density, current waveform, temperature, hydro-dynamic conditions at the electrode surface and by the number and thickness of the inter layers of the deposited materials. The paper describes the fundamentals of the electro deposition of multilayer systems. For the investigation of the properties of the multilayers different techniques are applied. One of the most important parameter are the thickness of the total layer and of the applied sublayers. The thickness of the sublayers can be varied between a few nanometers up to micrometers. The wear resistance, the contact resistance and the plug-in forces are measured as these parameters are important for the technical application of such layers. For the description of the structure composition and surface properties the sample where also investigated by scanning electron microscopy (SEM), energy dispersive x-ray-analyses (EDX) and glow discharge optical spectroscopy (GDOS). The paper shows that the deposition of gold based multilayers is possible and that the properties of such systems can be varied in a wide range what opens new fields of applications of such materials.

Oct 1, 2003

By G. K. Livingstone

"This paper describes mining conditions in the Kaiser surface and underground coal mines in the Sparwood area of southeastern British Columbia. Mining methods are explained, major mining equipment is listed and production rates are given. Reclamation methods and results are described. Data are given on safety organization, safety practices, accident statistics, safety inspections and absenteeism. IntroductionThe coal mines of Kaiser Resources Ltd. are located in the southeast corner of British Columbia. All present mining is in the Sparwood area, where operations began in 1900 with the opening of the Michel underground mines. Production increased rapidly at first, then went through successive periods of depression and prosperity. Following are the highlights. Quantities are in clean, short tons. 1900 1910-Rapid rise in production to a peak of 512,000 tons in 1910.1911-1924-Reduced rate of production, averaging 238,000 tons per year, due to strikes, manpower shortage during World War 1 and post-war depression.1925-1929-Second prosperous era, with production climbing to 383,000 in 1929.1930-1933-Second depression-production falling to 231,000 in 1933.1934-1942-Third era of prosperity-production recovered and new production peak of 908,000 tons reached in 1942 during World War II.1943-1956-Corttinued prosperity, with production averaging 720,000 tons per year.1957-1959-Loss of markets to oil and gas; production dropping to 517,000 tons in 1959.1959-1969-Recovery due to new coal market in Japan; production climbing back to the 900,000-ton level.197D-Present-Jump in production reaching 6.6 million tons in 1975. This was the result of the purchase of the property by Kaiser Steel, who negotiated a large-volume, long-term contract with Japan, built the coal port of Westshore, reduced shipping costs by instituting unit trains, and reduced production costs by investing in large-scale mining machinery and a new preparation plant."

Jan 1, 1980

By Y. Nishida, Y. Nara, T. Ishida

Understanding time-dependent deformation and fracturing in rock is essential, because the information of the long-term stability of rock is required for many sub-surface structures excavated in a rock mass. Time-dependent fracture propagation has been invoked as a potential key mechanism responsible for the increase in seismicity preceding earthquake ruptures. In engineering projects and in preventing natural hazards, the study of time-dependent fracturing is necessary. Subcritical crack growth is one of the main causes of time-dependent fracturing in rock. For silicate rocks, subcritical crack growth has been investigated by various researchers. It has been clarified that surrounding environmental conditions (temperature, humidity, and existence of water) have strong influence on subcritical crack growth in silicate rocks. Therefore, the information of subcritical crack growth in silicate rocks has already been enough. On the other hand, information of subcritical crack growth in carbonate rocks is not enough. Especially, the influence of surrounding environment on subcritical crack growth in carbonate rock has not been clarified yet. In this study, we investigate subcritical crack growth in carbonate rock experimentally using a fracture mechanics testing method. Marble obtained in Skopje in Macedonia is used as a carbonate rock sample. The Double Torsion method is used to measure the crack velocity and stress intensity factor. Especially, influence of water on subcritical crack growth in Macedonian marble is investigated. It was shown that the crack velocity in water is much higher than that in air at the same temperature. Based on the results of subcritical crack growth measurements, the long-term strength is evaluated for marble. It was clarified that the long-term strength in water is lower than that in air in marble. It is concluded that water has a remarkable influence on subcritical crack growth in marble. It is also considered that the long-term stability of carbonate rock masses should be ensured in a dry environment.

Jan 1, 2015

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015