Search Documents

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By S. Y. Mostowy, P. W. M. Shibley

"When Texas Gulf Sulphur Company discovered the Kidd Creek ore body in 1964, a crash program began almost immediately for the design and construction of a modern concentrator. It was necessary to mill two distinct ore types; one containing copper and zinc, the other lead, silver and zinc minerals. The final concentrator design was to handle 9,000 tons of ore daily in three circuits. One circuit was to treat copper-zinc and another lead-zinc ore exclusively on a permanent basis. A central circuit was designed with adequate flexibility to treat either of the above ore types in accordance with planned mining schedules. Ecstall Mining Limited, a wholly owned subsidiary, now operates the mine and concentrator complexes for Texas Gulf. The mine is located 15 miles north of Timmins and the concentrator 15 miles to the north-east along Highway 101. The ore is hauled from the mine to the concentrator over a 17-mile railroad. Initial milling operations began in November, 1966.1 - ABSTRACTThis paper deals with bulk reagent handling at the Kidd Creek concentrator. The reagent section at Kidd Creek has operated excellently since milling began in 1966. The bulk handling techniques are satisfactory. They have contributed substantially to good working conditions, economical practices and metallurgical efficiencies. The bulk handling features described should be considered in existing and proposed concentrators."

Jan 1, 1970

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By J. B. C. Wu, B. McKee

"Mining along with subsequent processing of the minerals often presents conditions where a wear- and/or corrosion-resistant alloy is needed to minimize downtime and maximize efficiency. This paper is intended to give an overview of the alloys that are currently being used, as well as those developed in recent years that could be used in the mining industry. Emphasis will be put on the iron-, nickel-,cobalt-based alloys and composites containing a variety of carbides. The characteristics, properties, product forms, and methods of application are presented. In addition, examples of the actual use of these wear-resistant materials are illustrated.IntroductionPreventing wear and corrosion is important in any industrial operations. In the mining industry, the process equipment typically suffers many different types of material degradation. Abrasion, impact, erosion, metal-to-metal wear and corrosion are typically encountered. Each situation requires different material characteristics to retard the degradation process. Therefore, it is essential to understand the characteristics of the materials and the effects of the alloying elements.There are four common classes of metallic materials for resisting wear and corrosion; namely, iron-based alloys, nickel-based alloys, cobalt-based alloys, and carbide-containing composites. Each class of material has its own characteristics. Depending on the chemical composition, the materials within each class can be vastly different in properties. In recent years, there have been materials developed in each of the four classes using the knowledge of the metallurgical principles and the effects of the alloying elements on the material degradation process.To use a wear-resistant alloy, it is also necessary to understand the available product forms and their application methods. Weld overlaying is a traditional way of using these alloys (Wu and Redman, 1994). In recent years, thermal spray is becoming popular. For applications where over-laying and spraying are impractical, solid components can be made by a variety of casting and powder metallurgy techniques. They can also be fabricated from the wrought products.To select a proper material for an application, it is important to understand not only the characteristics of the wear-resistant materials but also the degradation process. Due to the complexity of the processing environments, past experience is also helpful in making the decision on the material selection."

Jan 1, 1997

By Paul Stothart

Context ? Industry is active in urban, rural, and remote regions ? Faces a range of environmental challenges and ?social license? issues ? There are also Aboriginal and northern issues ? Also very active internationally, with associated challenges ? Environmental/social groups often target the industry ? The important contribution of the industry should not be overlooked Useful Minerals and Metals Minerals are intrinsic to the residential, municipal, communications, and transportation infrastructure of modern life. Examples: Hybrid motors - nickel hydride batteries Water purification systems ? nickel, rare earth elements Catalytic converters - cerium Screens and monitors - several rare earth elements Clean electricity - uranium Circuitry - gold, copper, aluminium, lithium, titanium, silver, cobalt, zinc Instruments - copper, silver, nickel, cobalt, copper, brass Protective products ? zinc, calcium carbonate, sulphur

May 1, 2008

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By Kent Zehr

Suncor Energy Inc. is an integrated producer and refiner of oil and gas headquartered in Calgary, Alberta. The bulk of revenue comes from the Oil Sands Group (OSG) operating in the McMurray formation of the Athabasca Oil Sands. Located some 25 kilometers north of Fort McMurray, Suncor OSG began life in 1967 as Great Canadian Oil Sands, the first operator to successfully enter commercial production of synthetic crude oils from the area. For most of the last decade, dramatic growth has been the standard mode of operation for Suncor OSG. Production of synthetic crude first reached 100,000 barrels per day in 1997 and less than five years later is averaging in excess of 200,000 barrels per day. Within this dynamic organization, Suncor Extraction is the business unit that processes run-of-mine ore into clean diluted bitumen for Upgrader feedstock. Extraction also delivers and places the barren sand and process affected water into tailings storage in one of several ponds from which water is recycled to support the various processes. For reference purposes, Extraction on a typical day currently receives more than 400,000 metric tons of oilsand ore, which is all processed to water based slurry for separation in one of two extraction plants. Separated tailings are disposed of as a slurry and the cleaned bitumen froth is diluted with naphtha and sent to tankage for storage until required by the Upgrading Unit. As a consequence, on a typical day Suncor Extraction pumps more than 1,000,000 tonnes of aggressive slurry into and out of the two extraction plants.

May 1, 2003

By Jucheng Wang

Unplanned open stope dilution is a major cost factor for many mining operations, even though significant advances in empirical and analytical approaches for estimating stope dilution have been made. Many factors that influence hanging wall dilution are still either ignored or assessed in purely subjective terms. Undercutting the stope hanging wall on both the overcut and undercut development are well recognized factors which contribute to hanging wall instability and dilution. In many mines, undercutting the hanging wall breaks the integrity of the rock mass that may form along continuous foliation or bedding planes parallel to the stope hanging wall contact, reducing stability. This undercutting also increases the zone of destressed or relaxed rock that may potentially fall into the open stope as dilution. An approach is introduced for quantifying the effect of undercutting on potential stope dilution. An extensive database of stope case histories has been collected to look at dilution from Hudson Bay Mining and Smelting operations (HBMS) in Flin Flon.

May 1, 2002

By J. Paraszczak

ABSTRACT: Application of teleoperated and automated (or “autonomous”) mobile equipment in under-ground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Jan 1, 2010

By M. Bueno

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By Rodney S. Read

This paper outlines a reasoned argument why no large-scale fracturing or faulting will be induced in the host rock by a deep geological repository (DGR) for nuclear fuel waste. Four DGR designs in three possible host rocks, including crystalline and sedimentary rock types, are considered. The reasoned argument draws from results of previously conducted thermal- mechanical analyses and new scoping calculations, along with evidence from experiments conducted in Canada and elsewhere. It is concluded that large-scale fracturing in the far-field is implausible given the expected in situ stress conditions in relation to rock strength. Near-field damage development and fracturing are expected in DGR scenarios in the different rock types, but these near-field effects are not expected to lead to large-scale fracturing that could compromise the integrity of the DGR and surrounding rock mass. Additional analysis and characterization activities are recommended to further validate the reasoned argument. Thermo-poroelastic loading of the rock mass is identified as one possible driving mechanism that should be studied further.

May 1, 2009

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By J. L. Bowlby

OWING to the pressure of routine analyses at the laboratory during the past year, work of an investigational nature on water problems has been greatly curtailed. Favourable reports by the boiler inspectors indicate that the operators are giving satisfactory attention to feed-water treatment at the several . power plants. Some of the operators prefer lime and soda, others the phosphate and soda treatment. Springhill is still on the same commercial treatment as they were using last year, and satisfactory results are being obtained. This individual preference for a particular treatment, although it may be different for feed waters of similar nature, indicates that so long as proper conditions of alkalinity and concentration are maintained within the boiler, it is immaterial what chemicals are used in the treatment. This statement refers, of course, to the low-pressure boilers. In high-pressure boilers, a treatment such as lime and soda cannot be satisfactorily employed, on account of the precipitated calcium carbonate unduly increasing the amount of suspended matter. Only one case of impending trouble was reported during the year. That was at Seaboard, shortly after the new unit was placed in operation. Dissolved oxygen, considerably in excess of the permissible 0.030 cubic centimeters per liter, was detected at various points on the feed line. It was suspected that a de-aerating heater was being operated at too low a temperature, and chemical tests, made before and after the necessary adjustments, proved that this was the source of the trouble. While it has been impossible to give mine waters the attention they require, progress can be reported in the work carried out by the Mechanical Department. Past investigation of the action of mine water on various acid-resisting alloys is now bearing fruit, and it can safely be said that repair work on mine pumps has been reduced by nearly one-half.

Jan 1, 1938

By F. Habashi

Lead is an ancient metal. The alchemists related it to the planet Saturn. It was largely obtained by smelting galena which generally contains small quantities of silver. That is why the metallurgy of lead was closely related to that of silver and in some cases the ore was treated only for its silver content. It was also known during the Roman time that lead vapors were toxic. Lead has been produced exclusively by pryrometallurgical methods. Lead refining is a complex process because of the presence of deleterious impurities such as arsenic, antimony, and bismuth. In the nineteenth century lead played an important role as a material of construction in the manufacture of sulfuric acid. In the twentieth century tetraethyl lead was used exclusively as an anti-knock reagent. In recent years lead is mainly used for making batteries.

Jan 1, 2008

By W. E. Johnston

At last year's Annual Meeting a paper by Haultain and Johnston was presented entitled Is the Gold in Tellttrides Soluble in Cyanide? Since then the writer has continued the study of various phases of this problem. Samples and specimens of ore from some of the Kirkland Lake mines have been studied and non gold-bearing tellurides have been found in these that are not soluble in ordinary mill solutions. Samples of tailings, both old and recent, from this district have been examined with apparatus and methods that have proved very successful in detecting the presence of extremely minute quantities of tellurides. Tellurides, both base-metal and gold-bearing, have been discovered in these tailings, but only in such minute quantities that their presence would not affect the ordinary assay results. More free gold particles have been found in the tailings than gold-bearing tellurides. Much experimental work has been done on tellurides, concentrated from high-grade material and from ordinary run-of-mine ore. The gold-bearing tellurides behave very much as does gold itself. Finely divided particles are dissolved fairly rapidly, coarser particles more slowly. All the tellurides are soft and brittle and also have a high specific gravity, with the result that they are extremely finely divided in ordinary mill practice. The ordinary high-lime solution of Kirkland Lake practice is suitable for the dissolving of the gold tellurides. Oxygen is necessary, but apparently not more so than in dissolving gold. Some particles have been found that appear under the microscope to be ordinary metallic gold particles, but on heating they show a small telluride content. These appear to dissolve more slowly than gold. There is considerable variation in the ratio of tellurides to gold from different points in the mines. So far the writer has failed to find any connection between this ratio and the richness of the ore. Generally speaking, the base-metal tellurides predominate. Some of these contain gold but this may be due to a mixture of tellurides in the one particle.

Jan 1, 1933

By D. L. Johnston

"Function and ApplicationsWater-only cyclones, (WOC) are a dynamic mineral separator which cause minerals to separate in a water medium by virtue of difference in specific gravity. Figure 1 shows diagramatic plan and sectional views of a water-only cyclone.A slurry of mineral matter and water is fed through the inlet opening under gravitational or pump pressure. The combined effect of centrifugal action and conical shape is to concentrate the heaviest fraction of mineral on the periphery and bottom of the cyclone. This layer of higher specific gravity particles increases in thickness and density between the cyclone inlet and apex. The action in the bed of higher gravity particles formed in the flattened portion of the cone surrounding the tip of the vortex finder deter;nines the specific gravity of separation or cut-point. Mineral particles of lower specific gravity flow with the bulk of the water, out the vortex finder. Mineral particles of higher specific gravity flow with little water out the apex. A more technically e:mct description of the functioning of the water-only cyclone can be found in previous publications noted in the references.The water-only cyclone was invented and refined by J. Vis man, formerly of the Canadian Mines Branch staff, between 1958 and 1965. The first industrial application noted in the literature was when it was introduced as a cleaner for fine coal in 1962. Since 1970 the water-only cyclone has become a common separation apparatus in many Canadian and foreign coal processing plants. The only other mineral industry application known to the author is in separation of gold bearing heavy minerals from sand<'>. The potential does exist for other applications and this area deserves to be investigated more thoroughly than it has been."

Jan 1, 1989

By J. H. Nantel

Indications are that underground mining is gaining favour with large and small mining companies due to environmental and sustainability concerns. Dramatic changes to mine fill technologies will be needed in order to keep pace with these emerging trends. The industry will be compelled to gravitate toward zero discharge mining operations. Innovative handling of mine tailings will become a focal point in this effort. The challenges are to use a greater portion of the residues and to manufacture a fill with better properties. This is a tall order that can only be addressed through a systematic research and implementation process involving mining companies, universities, research organizations, manufacturers and governments. The mining industry has to be at the forefront of this technology push in mine fills for the future mines. It will also be called upon to lead the way in other research areas. The industry will have to partner with other technology providers: universities, government laboratories and consultants.

May 1, 2007

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969