Search Documents

By Giovanni Lombardi

In order to get a clear overview of the grouting works carried out, to avoid misinterpretations of the data and functions shown on the display of the grout monitoring device, it is recommended to keep the flow rate as constant as possible. Obviously, at the beginning of the process, the flow rate will increase from nil to the selected "basic" value. An important question frequently addressed is also how to reduce the flow rate in nearing the GIN limit so to finally reach the target intensity. Depending on the actual conditions, there are different manners to proceed. However, the following one appears to be the most convenient. It is represented on Figure 25. Being GIN the target intensity, two new limits at, let's say, 0.95 GIN and at 1.05 GIN as shown in the figure should be defined. The selected basic grout flow rate "q0", is kept as constant as possible all along the grouting process until the 0.95 GIN limit is reached. The flow is then reduced step wise to 2/3 q0, 1/3 q0 and zero at crossing each of the three limits. A similar rule can be used in respect to the maximum pressure, while for the maximum volume the process can be stopped at one time. Obviously the number of successive limits and thus the number of steps in reducing the pressure, as well as the width of the fringes defined in said way may be adapted to the local conditions.

Feb 10, 2003

By Dawn Shuttle

In trying to find a grout, or some kind of stabilizer that would work in this application, we established some performance criteria. Of those, what I controlled the most was viscosity, then I had a whole list of other criteria. I needed a long, controllable gel time, durability and the ability to set and stabilize the soil. So I looked through a lot of different stabilizers, some really crazy ones and also the typical chemical grouts that are used. The typical chemical grouts were eliminated because of long-term durability concerns, the need for having extended gel times, and several other concerns. I would be happy to discuss that with you further after the talk if you're interested. But, generally it was based on viscosity, gel time, and the need for extended gel time. In terms of the relative density of the sand many other grouts could have been used. But the main issue was trying to develop this way to do low pressure grouting that would not cause invasive disruption of the site. We couldn't go in and grout it, put centers, so most of the other grouts wouldn't work for various reasons. The forty percent relative density samples were prepared by plubiation. That was both during the cyclic testing stage of the research, which happened a few years back, and also during the box model and the laminar box models at RPI. In terms of what criteria were used to determine the success of the grouting, when I initially started this work what I did was take the grouted samples and I subjected them to cyclic triaxial testing. What I did was take a look at the cyclic deformation resistance of different concentrations of grouted colloidal silica treated sand. I looked first at 20% concentration because I wanted something that I knew worked and then I gradually decreased to 15%, 10%, and 5%. What I was most concerned with was that it did not liquefy and that it was able to hold together it and experience some deformation. But most importantly it needed to not liquefy. So, that was the biggest issue in determining the success of the grouting. In terms of the centrifuge modeling it was done by looking at several components: from looking at the pictures of the bending moments, looking at the acceleration records and how the acceleration records were transferred through the soil, looking at the reduction in the lateral displacement and those kinds of issues. So let me show you the difference.

Feb 10, 2003

By Braxton P. Erbe, Douglas C. Brunot

A variety of systems and techniques exist to support deep excavations where sloping is not feasible. This paper will explore an example project involving the use of pre-engineered hydraulic bracing systems to support sheet pile walls. Challenges on site that drove the final design include a high water table, irregular excavation geometry, and underground obstructions. The hydraulic system, connected by pins and not requiring welds, allowed for quick deployment and the modularity to change as required due to unforeseen site conditions.

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By Mohammad T. Izadi

Piles are, often, used for transferring load from the super structure through soft consolidating strata onto relatively stiff uncompressible soils. Downward movement of the soft soil strata develops negative skin friction and dragload around the pile shaft, with time. Traditionally the induced dragload is considered in determining the pile bearing capacity. On the other hand, field measurements on instrumented piles show that negative skin friction is reduced by the magnitude of applied live load. A method for calculating the pile bearing capacity, driven through soft consolidating strata is presented. In this method, two allowable load-bearing capacities are calculated for each pile, live load plus dead load and dead load. The proposed method, substantially, increases the allowable load bearing capacity of piles compared to calculated values by the traditional methods.

Jan 1, 2001

By Manchanda H, Agarwal J.

The construction industry has one of the largest numbers of injuries compared to other industries. Thus, reducing accidents and determining construction risks are extremely important. One of the essential steps for construction safety management is hazard identification and risk assessment, since the most unmanageable risks are from unidentified hazards. While the urban rail transit systems are being developed rapidly in almost all major cities of India, adjoining Existing Building Structures and historic sites are facing possible threats of unexpected damages and accidents. The protection of these structures becomes one of the major challenges specifically when the infrastructure being developed involves construction of underground tunnels passing through old cities. The assessment of settlement induced damage on buildings during the preliminary phase of tunnel excavation projects, is nowadays receiving greater attention. Analyses at different levels of detail are performed on the surface building in proximity to the tunnel, to evaluate the risk of structural damage and the need of mitigation measures. The current paper presents current practices being adopted in India for prediction and excavation of tunnelling induced ground movement and building damage risk-assessment. The paper highlights empirical and numerical approaches towards predicting settlement induced damages on buildings during the tunnelling, detailed step by step methodologies for conducting building condition surveys, evaluating associated hazards, and adopting adequate building risk identification and mitigation methods. The paper also discusses associated technical and contractual challenges and highlights way forward to overcome them.

Sep 1, 2022

By Ali Ebrahimi, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, Roneet Das, William Tanner, Amir Ahmadipur

There are safety concerns related to operation of heavy equipment over coal combustion residual (CCR) impoundments during construction of the impoundment closure programs. As part of a pilot study prior to a full-scale closure construction, an access pathway and working platform were designed and constructed to facilitate equipment access for construction of deep soil mixing (DSM) zones on the ash delta of a CCR impoundment. The access pathway and working platform was constructed using shallow mass mixing with cement at the CCR surface to address safety concerns related to the geotechnical behavior of CCR. This paper describes the data from the instrumentation system which was implemented to monitor the geotechnical performance of the CCR during the pilot study. The instrumentation system included monitoring of the ground movement, vibration, and porewater pressure within the ash delta of the CCR impoundment during a pre-construction load testing, equipment mobilization over the access pathway, and DSM column installation over the working platform. INTRODUCTION A deep soil mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment to evaluate mix designs and construction techniques for the regulatory closure. The DSM columns will create a wall which will separate and retain the CCR in a consolidated footprint separate from the closure by removal portion of the footprint and provide a barrier between the two areas of the surface impoundment. Historically, the surface impoundment received CCRs including fly ash, bottom ash, boiler slag, and gypsum, along with other byproducts produced from flue gas desulfurization (FGD). The predominant CCR in this impoundment were fly ash and bottom ash. The primary goals of the DSM pilot study were to assess the mix design strengths and to evaluate DSM construction techniques that could reach the design mixing depths of up to 90 ft. The DSM test columns were installed on the CCR delta approximately 500 ft from the nearest impoundment dikes. Another objective of the pilot study was to develop, construct, and monitor an access pathway for safe passage and movement of construction equipment on the CCR delta.

Jan 1, 2019

By Haoran Zhang, Chu Ho

A recent design-build project in New York involved various degrees of additions and improvements to four existing transit stations. Reuse of the existing foundations was considered a more sustainable alternative than constructing new foundations for the project. This approach mitigated the extent of demolition work and limited the amount of downtime for track operations. A key challenge for reusing the existing foundations was the lack of as-built drawings. In order to obtain some measure of confidence for the proposed foundation reuse, non-destructive investigation technology was adopted to evaluate the structural integrity of the piers and foundations. A total of 47 piers for the existing passenger platform were investigated for possible reuse. Several test pits, excavated to verify the foundation type and configuration, indicated the piers were founded on a combination of shallow footings and drilled shafts. Pile integrity tests were performed to verify the length of the drilled shafts. Geotechnical capacity of drilled shafts was evaluated for side friction and end bearing resistance, and confirmed using a proof load test conducted from the existing platform structure. This paper presents the investigation methodology and discusses the approach adopted for geotechnical design of the existing foundations for reuse.

Sep 8, 2021

By Dimitrios Polantzas P. E., Collin E. Sweeney E. I. T., Franklin M. Grynkiewicz P. E., Leili Javidanian P. E.

In the latest AASHTO design specifications, the Load and Resistance Factor Design (LRFD) method is prescribed for the design of retaining walls. However, inconsistencies arise when LRFD is used for retaining wall design versus the traditional Allowable Stress Design (ASD). Required toe embedment and wall loading demand vary greatly when the two design approaches are compared, all else being equal. This is due to application of linear load factors to properties that vary non-linearly in the design. These inherent inconsistencies are further intensified when introducing factors such as layered soil profiles, different wall types, groundwater elevation, and surcharge requirements. When applied correctly, these two design approaches, in theory, should lead the designer to the same result with little discrepancy, as they do with steel structure design. However, the use of the current AASHTO LRFD method for various geostructural retaining wall designs yields contradictory results that suggest existing retaining walls that have been successfully designed and constructed are unstable. Fundamentally, LRFD should be built on reliability-based calibrations; the successful past performance of existing retaining structures designed using ASD suggests that the LRFD approach requires considerable modification. The authors of this paper recommend that the current LRFD load factors be reviewed and revised based on more comprehensive wall performance data and wall type such that the difference between retaining structures designed using LRFD and those designed using ASD is eliminated.

Oct 1, 2022

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Karl A. Higgins, Michael D. Venezia

The South Capitol Street Corridor Project is one of the District Department of Transportation’s (DDOT) largest projects, and is currently under construction. This case study will focus on the design of the foundation piles for the main spans of the iconic Frederick Douglass Memorial (FDM) Bridge, and will include a discussion of the foundation design evolution from an originally designed alternative foundation system (i.e. coffer dams and drilled shafts), to the current use of driven Large Diameter Open End Pipe (LDOEP) Piles. The paper will provide a discussion of the design methodology used during preliminary engineering and final design, and will highlight insight gained from the extensive load testing program completed to date. The load testing program consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre-production test piles. Specifically, data gathered during the nearly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles. This paper will also discuss limitations of currently accepted industry design methods for predicting the capacity of LDOEP piles, a subject that is also currently being researched by FHWA. The data from this test pile program will help design assumptions for future projects. INTRODUCTION The Frederick Douglass Memorial (FDM) Bridge carries South Capitol Street across the Anacostia River in Southeast/Southwest, Washington, DC, and is owned and maintained by the District Department of Transportation (DDOT). The existing FDM Bridge is nearly 70 years old, serves as a major artery into the city, and has been classified as functionally obsolete. As a result of the condition, age and limitations of the existing bridge structure, DDOT deemed it necessary for complete replacement of the bridge. The replacement project consists of the construction of a new bridge traversing the Anacostia River, as well as the reconfiguration of the Suitland Parkway and I-295 interchanges located at the eastern terminus of the FDM Bridge. Final design and construction services for the replacement project were procured by DDOT through a Design-Build contract. This paper will focus on the driven Large Diameter Open End Pipe (LDOEP) Piles used for support of the main span of the new FDM Bridge which is currently under construction. Discussion regarding the LDOEP Pile design methodology has been included, along with commentary regarding currently available industry guidance related to design and construction of LDOEP Piles. Much insight has been gained during the mostly-completed and extensive load testing program which consists of a combination of high strain dynamic testing (PDA), as well as Statnamic Load Testing on select sacrificial, pre- production test piles. Specifically, data gathered during the mostly-completed load testing program suggests the development of significant internal shaft frictional resistance within the tested LDOEP Piles.

Jan 1, 2019

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Leo Panian, Ryan Nagle, Priyanshu Singh, Gina Carlson, Wayne Magnusen

"This case study presents the design and construction of an integrated foundation and ground improvement solution utilizing deep soil mixing (DSM) and micropiles. 270 Brannan is a midrise office building in San Francisco that straddles the historic shoreline that was reclaimed in the 19th century. Subsurface conditions include shallow bedrock inland of the historic shoreline, and steeply dipping bedrock overlain by 60 feet of compressible deposits and liquefiable fill on the bay side. Project challenges included mitigating the liquefaction and lateral spreading hazards, addressing settlement concerns in the fill and the bay deposits, developing a cost-effective foundation support solution, assuring satisfactory seismic performance, and addressing construction restrictions with existing adjacent structures.DSM combined with micropiles was identified as the most cost-effective solution for the ground conditions. The DSM panels act both as a liquefaction mitigation mechanism and a foundation support system. Resistance to seismic overturning is provided by uplift-resisting micropiles. The DSM-micropile solution allows the use of efficient conventional spread footing foundations, integrating isolated micropile groups to anchor the shear walls. Successful installation of the system relied on a program of field testing to validate the design and conformance with the design criteria.INTRODUCTIONThe regular grid of surface streets within San Francisco’s South of Market (SOMA) district provides little evidence of the geotechnical complexities that lie below. In the late 1800s, sand dunes, bedrock hills, cliffs, marshes, and mud flats were flattened and filled, concealing their locations and characteristics. The 1906 San Francisco earthquake and fire leveled many buildings in SOMA; new buildings were built after 1906 – often on top of rubble and debris from the structures that came before. Locally, the combination of natural geology and historical interventions can produce complex subsurface conditions that vary dramatically over short distances. This is particularly true at locations where tidal mudflats once met bedrock hills at the shore of San Francisco Bay.This case study describes an integrated foundation and ground improvement system implemented for a multistory “Class A” office building at a complex SOMA urban infill site. The system utilizes cement deep soil mixing (DSM) in combination with spread footings and micropiles to address a range of design and construction issues, including liquefaction and lateral spreading mitigation; consistency of earthquake ground motions; shallow foundation support; seismic uplift resistance; and avoidance of loading adjacent basement walls. The system was implemented by a technically-sophisticated owner through a process that included constructive collaborations between the project geotechnical engineer, structural engineer, general contractor, and specialty foundation and ground improvement contractor(s). The system is designed to cost-effectively provide a high level of seismic performance."

Jan 1, 2017

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Peter Deming

"PART 1 OF 2INTRODUCTIONSlurry trenches are the least cost hydraulic barrier available, if the excavated spoils can be recycled into backfill. As such, slurry trenches are constructed where possible, sometimes at high risk. Slurry trenches are also used to install biopolymer drainage trenches, which have a low safety factor because the biopolymer slurry weight is marginally greater than the weight of water. In marginal ground the construction risk falls to both the Owner who designs and asks for the construction, and the Contractor who manages the work and promises to complete the project successfully. This paper discusses design and construction of slurry trench barriers in marginally stable ground and where groundwater chemistry invokes the need for slurry management details to obtain proper backfill placement.As a designer, Mueser Rutledge Consulting Engineers works for both Owners and Contractors. We are usually able to convince Owners of their responsibility for design detailing in order to obtain a working final product and to obtain reasonable bids from Contractors by disclosing construction needs and designing to reduce the contractor’s exposure. We often work for Contractors to produce designs which result in successful construction in projects where the Owner’s engineer places the responsibility of design and construction on the Contractor.This paper is intended to inform both Owner and Contractor audiences of resources which are available to reduce the risks of trench collapse in difficult ground conditions. We hope it serves this purpose.DESIGNSubsurface InvestigationsSubsurface conditions should be defined by borings focused on definition of the soil profile and soil design parameters. After general subsurface conditions are defined, barrier borings should be drilled along the final alignment.Definition of Soil Strength and CompactnessCompactness of sand and gravel strata should be defined with Standard Penetration Test N-values. The shear strength of cohesive materials should be defined by laboratory testing. Silt and fine sand strata with little cohesion should be investigated using mud rotary techniques to prevent disturbance. General strength characterization by soil layer should be used for analysis of trench wall stability."

Jan 1, 2006

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.IntroductionCement deep soil mixing (CDSM) was used as a replacement for stone column ground improvement in a corridor which the owner, the Washington State Department of Transportation (WSDOT) wanted to reserve for future trenchless crossings beneath reinforced soil embankments within a freeway interchange. The work was part of HOV improvements to I-5 in Tacoma, Washington. The CDSM construction occurred in late 2010 and early 2011.Approximately 14,500 cubic yards of soil cement columns were placed by CDSM. The soil cement improved ground supports permanent geosynthetic reinforced slopes up to 50 feet high. The ground improvement was designed primarily to provide global stability of the reinforced slopes during seismic loading, but it was also utilized to reduce the time and total amount of settlement following construction of the embankments.This paper presents a discussion of the design approach and challenges associated with quality assurance of a relatively small volume of CDSM within the time constraints of an ongoing project. The challenges associated with attempts at collecting cores of the cured soil-cement mix cured by triple tube coring and pushing a double tube into the wet mix and allowing it to cure insitu are discussed, along with the eventual adoption of sonic coring combined with reliance on laboratory testing of wet mix samples collected daily."

Jan 1, 2017

Jan 1, 1995

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021