Search Documents

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By D. Y. Peng

A Large Sub-structure with open top of S.Y.P. float line requires a 90m x 50m in plan and 13m-deep excavation in soft soil, Shanghai. The geological conditions in site are rather severe. The technology specifies that no permanent braces nor partition walls are allowed to be constructed inside. After a series of discussions the scheme of semi-gravity type cellular D-walling without any braces or earth anchors is finally adopted and successfully executed by SFEC. This paper deals with the technical problems in the design, construction and in-situ monitoring we met with in this difficult project.

Jan 1, 2010

By Don Deardorff, Ke Yang, Yingcai Han, Ken Sorensen, Robert Kruger, Mark Petersen, Diane Fiorelli, Larry Goldfarb, Kathryn Petek, Kwabena Ofori-Awuah

Design of deep foundations for lateral loads requires an understanding of soil-foundation-structure response during loading. Lateral loads on a deep foundation (piles) could be due to earthquakes, winds, waves, and/or machine vibrations. Over the years, analysis of response of piles due to lateral loads evolved from closed-form solutions to p-y methods to strain wedge to finite element/finite difference modeling. Although analysis of lateral response of piles and shafts is routinely performed, there is no single guidance document and/or standard for design and testing. Several different analytical methods are available for the analysis, and the resulting design can result in significantly different responses which can create confusion. This is especially true for analyzing and designing piles in potentially liquefiable soils with lateral spread issues under seismic conditions.This guidance document is intended to assist geotechnical engineers, pile designers, and contractors in analysis, design, and testing of piles and drilled shafts for lateral loads. This document discusses the background of different analytical and testing procedures and presents the recommended methods for analysis, design and testing of piles for lateral loads.Chapter 1 defines the different kinds of lateral loads to which a single pile or pile group may be subjected. This first chapter also presents different types of piles used to resist lateral loads.Chapter 2 discusses geotechnical issues related to lateral pile design such as liquefaction and lateral spreading and other non-seismic issues. Also addressed in Chapter 2 is geotechnical site characterization (as related to lateral loads) in terms of site investigation, in-situ testing, geophysical testing, laboratory testing, and estimation of soil/rock properties.Chapter 3 discusses the background and available analytical methods and tools for the analysis and design of single piles and drilled shafts. Several methods of analyses from closed-form elastic solutions to the finite element/finite difference solutions and their applicability are discussed. Available commercial computer software packages for analyzing single piles and drilled shafts are also presented.Chapter 4 expands the discussion of single piles and drilled shafts into the analysis and design of pile groups. In addition, group effects, resistance of pile caps, results of previous experimental and analytical studies, and available analysis tools and software for pile groups are discussed.Chapter 5 presents the issue of lateral resistance of piles and drilled shafts as discussed in different national and international building and non-building codes. A summary of extensive research on several codes are presented to facilitate the compliance with different codes.Chapter 6 discusses structural design issues of individual piles and drilled shafts such as depth of fixity.Chapter 7 discusses soil structure interaction issues related to kinematic and inertial effects due to seismic loading and available methods of analyses.Chapter 8 discusses and presents the typical procedures for the lateral load testing of piles. This guideline was developed as an aid to the practicing engineer in providing information, direction and commentary on the lateral design of deep foundations. Although all reasonable effort has been made to accurately compile the material and information contained herein, no warranty is made with regard to any such material or information and the Deep Foundation Institute assumes no responsibility for any possible errors or any direct or indirect result of the use of any such material or information. It is not intended that this document address every factor affecting lateral design for every situation. Therefore it is the responsibility of the person utilizing information from this document to confirm that it is appropriate and correct for their situation as well as to understand and properly apply

Jan 1, 2012

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Abid Adekunte

"Engineers and developers have witnessed the growing popularity of deep basement structures as components of urban commercial and residential developments. This is often attributed to inadequate surface parking facilities in urban centres and a somewhat popular belief that underground parking facilities improve both commercial and aesthetic values of urban structures. For many years, diaphragm walls and sheet pile walls have been widely accepted as effective deep excavation support systems for basement construction in urbanised zones. However, these are now being replaced by bored pile retaining walls as preferred earth retention systems of choice on many projects for several reasons, which may include economy, faster installation process, reduced space requirement for machinery and ancillary equipment, flexural rigidity and axial capacities.However, there are complexities associated with the use of bored pile retaining walls on urban developments. These include; limitations due to vertical and horizontal installation tolerances, which is a major issue when wall is required to provide groundwater cut-off for multi-level basements as tolerances are difficult to achieve for deep piles, uncertainty associated with the prediction of wall axial capacity as piles are rarely tested, difficulties in using temporary props as wall restraint due to restricted working spaces in urbanised zones and difficulties in adopting ground anchors as restraint due to the existence of adjacent sensitive structures in built-up areas. Such complexities have resulted in cases of failure, non-serviceability and abandonment of basement construction schemes. Therefore, overcoming the intricacies associated with the application of bored pile walls is becoming a priority to the present day basement engineer.This paper is centred on the numerical modelling, design, construction and monitoring aspects of four recent case histories of multi-level basement and marine engineering construction schemes in the United Kingdom and the Republic of Ireland, which involved the use of bored pile retaining walls. The paper highlights the various customised approaches and innovative novel solutions adopted on the sites, to mitigate risks and ultimately overcome the intricacies associated with the earth retention techniques. Simple empirical equations for developing the geometry of secant pile walls for effective groundwater cut-off are presented and validated. An alternative approach for predicting axial capacities of bored pile walls is also presented; this is shown to be considerably less conservative than a common routine design approach, while also in good agreement with observations made in a recent series of laboratory-based scale model tests."

Jan 1, 2017

By Ronnie X. Gu, Xing Zheng, Gem-Yeu Ma

Due to implementation of the rotator construction method from which a smooth shaft was anticipated, a full-scale pile load test (Osterberg Method) was performed at Pier 14 Pile 9 of the main span of the New Benicia-Martinez Bridge to confirm the design parameters of the rock sockets. Two levels of load cells were fabricated in the reinforced cage of the rock socket. Each level consisted of three 670-mm Osterberg load cells with a total testing capacity of more than 50 MN in both directions. In an attempt to separate side friction and end beari ng, a 75 mm thick compressible Styrofoam material was placed at the bottom of the cage. The pile load test was carried out in four stages. The multi-level multi stage pile load test data was interpreted for casing friction, side friction for two rock strata, end bearing, and residual side shear values under repeated loading in opposite directions. The side friction from the casing in soils at Stage 2 is approximately 9 MN. The end bearing at the tip of the rock socket at Stage 3 was calculated to be approximately 17 MN at a displacement of about 75 mm. The residual side shear resistance for the 10 m 50% RQD rock strata was calculated to be 9 MN or approximately 50% of initial values, after being pushed 0.3 mm upward in Stage 1, 71 mm downward in Stage 2, then 55.5 mm upward again in Stage 3, and finally 105.3 mm downward in Stage 4. The test results surprising ly indicate that the side shear resistances from both low RQD intensely weathered rock and higher RQD slightly weathered competent rock are about the same at approximately 19 MN. This pile load test provides very critical information for confirming deep shaft design and analyses.

Jan 1, 2005

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Alice Arana, David M. Cacoilo, Joel L. Volterra

"To make space for the new South Ferry Station in lower Manhattan, engineers and contractors carved out a new tunnel beneath three operating subway tunnels and tangentially to yet another tunnel. Creating the space required the design and construction of complex temporary excavation support and underpinning systems and the design and installation of real-time monitoring systems. Construction for the new station and tunnel was mainly cut-and cover in a mixed-face area of soil and rock approximately 2,000 linear ft long, 60 ft wide and up to 70 ft deep. Close coordination between the design/build team and the project owner, the Metropolitan Transportation Authority (MTA), was critical.With the construction of this $400 million project, the MTA and New York City Transit (NYCT) are correcting the numerous physical and operational deficiencies of the existing station and improving the lives of millions of commuters. Built in 1905, the original South Ferry Station is on the IRT Broadway–Seventh Avenue Line of the New York City Subway and is the southern terminal of the #1 subway service, which forms a loop to return uptown. The station has a sharply curved single platform on the outside of the outer track of a two track loop. This platform is short and does not allow the rear five cars of a normal 10-car subway train to load or unload. In addition, once the train stops at the station, commuters wait while retractable floor grates bridge the gap created between the platform and the subway car doors, and then they have only one exit from the station. Spray nozzles keep the tracks lubricated to reduce the train wheels’ friction caused by the tight curve. The sharp curvature of the loop and the inability to use half of the subway car doors slow train operation. With the new ADA-accessible station, 10-car trains will be able to open all doors, and additional entrances, escalators and elevators will greatly reduce travel times."

Jan 1, 2008

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Matthew Janes

The RC Harris Filtration Plant, which treats the majority of the fresh water for over 2.5 million Torontonians, is a Canadian Architectural Heritage site demonstrating a classic example of Art Deco Architecture. The facility is undergoing an expansion to install an underground sludge treatment capability. Perched atop a bluff on the North shore of Lake Ontario the structure enjoys a commanding presence on the Lake Ontario shoreline. A series of underground tanks were proposed for the hillside below the structure, which when covered would preserve the building?s architectural presence. However, the plan required two, stepped excavations 12 m and 10m deep into compact, wet sands over stiff clays and clayey silts. Concerns regarding the original structure influenced designers to set the lateral deflection limit for the front footing of the existing structure at 4 mm, (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Analysis indicated installation effects and overall elastic movement of the soil mass beneath the building would result in movements of 7 to 9 mm at the structure. Through extensive FLAC analysis and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept. Based upon the analysis the design-build team negotiated a new deflection criteria dictating a maximum of 2.0 mm of movement across the critical expansion joint between the Filter Building front footing and the tank slab beyond. The contractor invested in additional pre tender soils investigation to support the refined design process. The FLAC analyses indicated the Filter Building movements would be elastic and distributed up to 50 m back beneath the front footing of the structure. An extensive precision monitoring program proved construction related movements of 6 to 10 mm horizontal at the front footing. Extensometers placed at two locations over the critical interior tank expansion joint showed no measurable movements. The overall monitoring program, including inclinometers, tilt meters, tie back extensometers (smart cables) and tie back load cells indicated a good match between recorded movements and loads and those predicted by FLAC Analysis.

Jan 1, 2006

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Patrick K. Wong, Richard Kelly

"The variability in strength and compressibility of in situ deep soil mixing products can be greater than the variability of the natural soil. However, satisfactory performance can be achieved by careful construction and an appropriate QA/QC program. This paper presents a case study on the use of deep dry soil mixing columns to support several embankments over soft clay along a highway project. Post-construction settlement monitoring indicated that good performance is achieved where the acceptance criteria are met, except in an area with high organic content. Embankments with contrasting performance are compared to the quality control test results which comprised laboratory testing of core samples as well as in situ test results such as pull-out and push-in vanes and conventional cone penetration tests. Drawing on the performance results and quality control testing, discussions and guidelines are given on quality assurance acceptance criteria and construction control testing regime for future projects.INTRODUCTIONBetween 2008 and 2012, the largest deep dry soil mixing (DSM) contract during that time in the southern hemisphere was carried out for the Ballina Bypass project. The project, comprising 12 km upgrade of the Pacific Highway located in northern New South Wales close to the border of Queensland, was commissioned by the Roads and Maritime Services (RMS) of NSW. The ground improvement contractor was Keller Ground Engineering (KGE) Australia. Seven different types of ground improvement techniques were employed for the project, ranging from low embankment strategy with nominal preloading, to surcharge with wick drains, light weight bottom ash fill, DSM, vibro-replacement stone columns, dynamic replacement, and vacuum consolidation (installed by Menard Bachy Pty Ltd). Different techniques were chosen depending on time program, cost, and performance requirements relative to proximity to piled structures (e.g. bridge abutments) and post-construction settlement and differential settlement for either rigid or flexible pavements at different locations.DSM was the most utilized ground improvement technique employed on the project, comprising a total of about 285 km of 0.8 m diameter columns to depths up to 18 m for the purpose of supporting bridge approach embankments and culverts with embankment heights up to 6 m. DSM was chosen due to the very soft nature of the clay soil with moisture content practically at liquid limit, and the relative speed and economy of the system. Dry cement powder at rates of 160 kg/m3 to 200 kg/m3 were pneumatically discharged via the hollow stem of the mixing tool, and mixed with the soil (using multiple horizontally mounted paddles on a single vertical stem) at high speed as the mixing tool is withdrawn."

Jan 1, 2015

By Brian Koch

Michels installed 242 drilled shafts to support the piers for a new basket-handle, true-arch twin bridge across the Mississippi River from Moline, IL to Bettendorf, IA. The installation of the drilled shafts was completed with the simultaneous use of two Liebherr LB36 and one IMT 300 drill rigs. Utilizing barges, 233 drilled shafts were installed in the river. Michels crews also installed 7-ft to 10-ft permanent steel casing into the bedrock, and drilled to depths of 60 feet for each shaft. Despite working in strong currents, freezing temperatures and on rocking barges, Michels crews placed the shafts within 3 inches of plan position. Since the drilled shafts are the key piece in supporting the bridge structure, Michels provided cross-hole sonic logging to verify the integrity and strength of the concrete within the shafts and to add another level of quality control for the owner/customer. Extensive planning took place each day to ensure that tugboats, the linchpin of the project, were being efficiently utilized to shift the barges and materials daily. On any given day, Michels transported five concrete trucks by barge from shore to shaft sites to pour between 40 and 240 cubic yards of concrete. The Michels environmental team was diligent with preparing, discussing and implementing a water treatment plan that was accepted by all state and federal agencies and adhered to strict environmental regulations. Grain hopper barges were rented to control and treat the water that was used in the drilling operations. Another challenge crews ran into was the discovery of caverns when drilling into some parts of the bedrock. Michels worked with the engineer to develop a plan to construct the drilled shafts that encountered the caverns.

Jan 1, 2019