Search Documents

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Jie-qun Zhai, Jian Jia, Ke Yang, Xiao-lin Xie, Yu Zhang

"With cities’ development, underground space exploitation presents a need for bigger and deeper constructions now. Technical problems founded during the construction of deep foundation pit support become more and more important. The supporting system has to cut or partly cut off hydraulic connection outside and inside the foundation pit, control the ground settlement caused by dewatering and make sure safety of foundation pit and its surroundings. Some preliminary study and application of ultra-deep soil reinforcement methods have been conducted in Shanghai’s deep excavation engineering. On the basis of engineering practice of ultra-deep foundation pit in Shanghai, some field and laboratory test, this paper analyzes effects of different ultra-deep soil reinforcement methods and their influence characteristics of surrounding environment. It also summarizes these methods’ sealing effect, construction and economic efficiency and concludes their characteristicsINSTRUCTIONShanghai is formed from marine sedimentation. In Shanghai, from earth’s surface to 30~40m underground, soil is mainly consist of soft clay with 40% moisture content. There are also many thin silty-sand layers in the earth, so the soil is both soft and permeable. Under 40m, soil is mainly thick silty-sand layers and fine-sand layers with medium density and confined groundwater whose water head is about 7m high.With the rapid development of Shanghai’s municipal construction and high-rise buildings in the recently ten years, the number of underground structure including subway station, tunnel and high-rise building basement are constructed rapidly. Due to the permeability and softness of Shanghai’s soil, it is necessary to reinforce soil to make sure the safety and high construction rate of engineering project in Shanghai.Because of deeper excavation depth and bigger excavation area in Shanghai, ultra-deep soil reinforcement is used preliminarily in Shanghai. Combining with engineering practice of ultra-deep foundation pit in Shanghai and employing field and laboratory test, this paper analyzes effectiveness of different ultra-deep soil reinforcement methods and concludes these methods’ characteristics and their applicability. All this can guide further application of these methods."

Jan 1, 2015

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By B. Philip Shull, Allen W. Cadden, Johanna M. Simon, Michael S. Senior

A 670 linear meter (2,200 linear foot) large-diameter sanitary sewer interceptor installation at depths ranging from 3 to 10 m (10 to 30 ft) below existing grade in an area with a high water table requires careful attention to design and performance of the system during construction. Highly variable soil and rock conditions at the site necessitated the design and construction of various excavation support systems along the alignment. In addition to the subsurface condition challenges faced at this site, the proposed sewer pipe was to be installed between an existing active combined sewer main and a high pressure gas main feeding the nearby city. What better way is there to monitor performance of the system than to require a detailed instrumentation system? Instrumentation system specifications and designs are becoming more commonplace in the industry, but it is always important to sit back and take a look at the whole picture. What are you looking to gain from your monitoring? What pieces of information are useful? What interpretations can you derive from the instrumentation you have selected? This paper will address the instrumentation system used to monitor the 670 m (2,200 ft) excavation from the specification requirements to the implementation and interpretation. This case history will delve into the challenges faced and methods used to overcome those challenges on this particular support of excavation (SOE) project. A combination of soldier pile, lagging and sheeting, and shoring systems was used to achieve the necessary excavation support. In designing the systems, attention was given to the configuration of the bracing system to allow the sections of largediameter pipe to feasibly be installed in the excavation while maintaining the SOE system.

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Danny Winters, Wesley Schmutzler, Christopher Lewis, Matteo Bertoni

"SR 83/US 331 is a primary North/South roadway in Walton County that is a crucial link for tourism and commerce between the Walton County beaches and the heavily traveled I-10 corridor in the panhandle of Florida. The facility also serves as the primary hurricane evacuation route from southern Walton County. This 3.4 mile project involves expanding the current two-lane crossing of Choctawhatchee Bay to a fourlane facility to increase capacity and dramatically improve mobility within the corridor. One of the major goals of the project is to perform ground stabilization using Deep and Shallow Soil Mixing (DMM & SMM) along existing causeways. Ground stabilization is required due to the existence of moderately deep very loose soils that have settled considerably over the years. As a result, the Florida Department of Transportation (FDOT) incurred significant maintenance expenses and was unable to maintain an acceptable ride quality. FDOT considered soil mixing as one option to control this settlement. Quality Control for soil mixing relies heavily on the monitoring system used to control mixing parameters. This paper will examine in detail, the reporting of the Drilling Mate System (DMS) used to ensure the quality of each soil mixed element.INTRODUCTIONThe Florida Department of Transportation (FDOT) issued a Design-Build Maximum Price Request for Proposal (RFP) for the Choctawhatchee Bay Bridge expansion. The design-build (D/B) team of Skanska/Parsons Brinckerhoff was awarded the contract. The D/B team, in order to meet the unique deep ground improvement challenges of the Choctawhatchee Bay Bridge Project, selected Foundation & Geotechnical Engineering (FGE) as the engineer to design the ground improvement and TREVIICOS South (TIS) to execute the works.The FDOT in their RFP states that “either bridge or utilize a deep ground improvement method to stabilize the three segments of the existing earthen causeway” and “one possible method of deep ground improvement which is considered viable is deep soil mixing”. FGE developed a proposal to provide a unique rigid transfer platform to effectively stabilize the existing causeways. This platform (Fig. 1) consists of an upper 10 ft thick stabilized soil layer which transfers axial load to a series of deep columns. This robust system guarantees superior durability, ride quality and pavement condition and will exceed all required design and performance criteria including, “Less than 2 inches of settlement within a 1,000-foot section”."

Jan 1, 2017

By W. L. Chong, Y. Zou

There are many types of Earth Retention Systems (ERS) available in the market where more than one method can be a feasible solution for a project. This paper examines the design and construct process of a project in Dee Why, NSW using a hybrid ERS comprising contiguous piles with jet grout infill. The development comprises a deep basement and mixed-use urban superstructure. The site is located in an area of variable ground conditions, high ground water table and in proximity to existing buildings with multi-level basements. This paper details a comprehensive assessment of the geological conditions and strategies adopted to better understand the effectiveness of the proposed product and to minimise the associated risks of the proposed solution. This involved conducting additional geotechnical investigation, extensive numerical modelling and in-situ monitoring of the movements and the performance of the walls. A monitoring regime consisting of inclinometers, survey points on capping beam and prisms on the neighbouring buildings and roads surrounding shoring wall was implemented. The monitoring results were back-analysed using computer software WALLAP, Plaxis–2D and Plaxis–3D for the post-construction examinations. This paper details the effectiveness and advantages of a hybrid ERS using contiguous piles with jet grout infill.

Nov 1, 2022

By Armin W. Stuedlein, Steven R. Saye

The differences between calculated axial pile capacity and the capacity realized during and following installation has long presented a significant concern for foundation engineers and contractors. Such differences have increased in prevalence with the increased use of larger diameter steel pipe piles and the significant increase in design-build contracting. The writers present concepts to close the gap between calculated axial pile capacity and the capacity realized during and following installation of driven pile foundations, including: (1) pile set-up in plastic soils, (2) limitation of re-driving of piles after setup which serves to reduce pile capacity, (3) the use of a vibratory hammer to install piles in cohesive soils disturbs the supporting soils and reduces the pile side resistance capacity significantly, and (4) long pile installation times for open-ended piles can damage the pile side resistance. Examples are presented from practice to illustrate these concepts and to guide pile installation planning to recognize the installation impacts and either consider alternate installation approaches or to properly consider the installation impacts during design.

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

"The Morris Island Lighthouse (MIL) is located between the jetties leading to the Charleston Harbor and Folly Beach, S.C. The present structure is the third lighthouse to occupy this location. The first navigational aid was erected in 1673, and consisted of a raised pan filled with pitch, which was set afire at night to guide early ships. The next structure was built in 1767, and constituted the first real lighthouse, standing 42 ft (12.8 m) in height. In 1838, a second lighthouse was built on the site, and it measured 102 ft (31 m) in height and featured a revolving light. This structure lasted until 1862 when Confederate troops, during the Civil War, destroyed it to deny its use to Union troops.Navigators steered these waters without a lighthouse for nearly a decade until 1876, when the current structure was built under the direction of the U.S. Army Corps of Engineers (USACE). In 1886, the Charleston area suffered a M7.6 earthquake. Significant damage was caused throughout much of the area, including a slight “list” of the lighthouse to the northeast. As a result, the cast of the beacon was reduced from 18 mi (29 km) to about 6 mi (9.7 km), causing much distress to navigators until the beacon platform was releveled and remains at this list to the present day.Conditions for ConcernThe current lighthouse was originally constructed about 1,200 ft (366 m) from the shoreline. Over the years, USACE has undertaken several programs to meet the increased shipping and navigation demands in the Charleston Harbor. Around the turn of the last century, two jetties were constructed, which drastically changed the approach direction for ships entering the harbor. In subsequent years, the harbor began to experience accelerated siltation."

Jan 1, 2017

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By Gerry Houlahan

"The 2015 Outstanding Project Award (OPA), which recognizes the superior work of DFI members, was awarded for the San Francisco- Oakland Bay Bridge New East Span. The award was presented to representatives from Caltrans and the T.Y. Lin International/Moffatt & Nichol Joint Venture at the DFI 40th Annual Conference on Deep Foundations in Oakland, Calif. A committee selected this project based on size, scope and challenges of the project; degree of innovation and ingenuity exercised; and the uniqueness of the solution to the difficulties of the job. A bridge across the bay between San Francisco and Oakland was proposed as early as 1872, but it took until November 12, 1936, until it became a reality. The bridge spans to the west of Yerba Buena Island were conventional suspension spans, while the east spans used a steel cantilever truss design and simple steel truss spans. This double-deck bridge served the Bay Area well until 1989. In that year, the magnitude 7.1 Loma Prieta earthquake damaged the East Span of the San Francisco-Oakland Bay Bridge. The resulting interruption to service across the bay demonstrated the vital role this bridge plays in the economic and life safety activities of the Bay Area. The project owner, California Department of Transportation (Caltrans), determined that the safest, most cost-effective solution was a total bridge replacement. The Engineer-of-Record, T.Y. Lin International/ Moffatt & Nichol Joint Venture, working closely with Caltrans, the Metropolitan Transportation Commission (MTC) and the California Transportation Commission (CTC), was charged with developing a comprehensive design strategy that met the project’s stringent criteria for seismic safety. These criteria included the new bridge’s designation as a regional Lifeline Structure that must open to emergency traffic shortly after the occurrence of a 1,500-year return period earthquake"

Jan 1, 2015

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021