Search Documents

By Azin Zangooi, Cesar Gomez, James Finch

Frother concentration is a variable which significantly affects the flotation performance by decreasing bubble size and helping froth stabilization. Variations in frother concentration, which mostly go unnoticed in industrial operations, may affect these functions. Some factors that can cause variations include the fact that frothers are normally dosed based on feed tonnage and not solution concentration, unstable frother delivery, incomplete dissolution for low solubility frothers, addition of frother-free wash water, remnant frother in recycle waters and frother partitioning to the froth. A colorimetric technique developed for determining frother concentration on site makes it possible to detect the occurrence of these problems and to establish their magnitude, allowing conditions to be adjusted to reduce frother concentration variations. By sampling and analysis, frother distribution throughout a circuit can be established, referred to as ‘frother distribution mapping’. Experiences at several concentrators processing sulphide ores are used to illustrate time restrictions for sample analysis, and to demonstrate temporal and spatial frother concentration changes as a consequence of variations in the grinding stage, recycled waters containing frother, and frother partitioning.

Jan 1, 2014

By Milind Chikhale, Ranjeev Kumar, Keshav Tyagi

Ore characterisation including mineralogy and beneficiation testwork of an ore is very important for determination of possible products and their quality. The results of such study help in ascertaining the beneficiation process route for the ore. The present study deals with ore characterisation study and beneficiation testwork on the samples of hematite iron ore with goethite impurity. The characterisation study reveals that the hematite is under alteration stage to goethite which has become an integral part of hematite. High goethite/limonite content is enhancing the loss of ignition content of the ore and reducing its Fe content. The findings indicate that in case of hematite iron ore associated with goethite and limonite, it is difficult to achieve high grade of concentrate above 65% Fe. It depends on the amount of goethite and limonite minerals and their association with hematite. These minerals contain aluminous impurities and hence, their rejection becomes essential. Separation of limonite and of goethite to limited extent is possible. In case of goethite, effective liberation is not achieved where it occurs as surface alteration product of hematite grains. The gangue mineral reported are clay and gibbsite, and are closely associated with iron minerals. The test work results indicate the grade and recovery of Fe along with alumina and silica content in lumps, sinter fines and pellet feed fines that can be achieved for the different ore types vis-a-vis the percent of available hematite in the ore. The recovery of iron is dependent on the hematite available and the loss of iron values in tailings is more because of rejection of limonite and goethite.

Jan 1, 2014

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and the dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is the main parameter for precipitate flotation in pilot or industrial scales. The suggested limiting factor is the aggregate stability under the turbulence created by the rising bubbles. The stability of precipitate is related to the structural organisation of aggregates, which determines the size distribution of particles during precipitation and flotation stages.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions. The fractal studies allow the detection of a structural scaled organisation of the precipitate flocs. The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with restructuring or breakage phases.The destruction process, which occurs for the lowest values of the dissipation energy E (0.02 . 0.05 W/kg) was characterised by a fractal dimension Dg of size distribution. Besides, the destruction of floc produces very fine particles, and thus induces the difficulties of bubble-particle collision during the precipitate flotation in column."

Jan 1, 2003

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By J. M. Ortiz, J. Haas, W. Kracht, G. Pamparana

This work explores the effect of ore hardness variability on the design of a solar photovoltaic system with battery storage and grid backup, to operate a semi-autogenous grinding mill (SAG). First, a case of two synthetic ore populations was studied, without any consideration of spatial distribution. The mean and variance of the ore hardness (measured in specific energy consumption, SEC) of both populations were subjected to a sensitivity analysis. The operation was evaluated with one and two stockpiles. The latter allows classifying according to ore hardness as a way to adapt the SAG energy consumption to the solar cycle. The results show that using two stockpiles allows achieving a larger autonomy (i.e. less energy imports) at lower total costs, especially when the difference of mean hardness between the two populations is large. The difference in variance (between the two populations) has a smaller impact on the design recommendations. Second, a case study was performed considering the spatial distribution of geometallurgical units. Two cases were considered: (a) brownfield, when there is historical information of the actual variability of the ore hardness; and (b) greenfield, when the system design relies mainly on geometallurgical modeling. Brownfield and greenfield planning result in similar sizing recommendations of the solar power plant, if precise drill cores are available. In this case, geometallurgical modeling is an effective tool for forecasting the energy demand necessary for designing the power plant.

Jan 1, 2018

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Gjergj Dodbiba, Toyohisa Fujita, Li Pang Wang, Masashi Yamane

"The platinum-group metals (PGMs), are currently receiving worldwide attention as they have major industrial uses. PGMs, i.e. ruthenium (Ru), rhodium (Rh), palladium (Pd), osmium (Os), iridium (Ir), and platinum (Pt), are widely used as catalysts in petroleum and chemical processes. In addition, they find wide applications in automotive exhaust-gas control converters and are of immense importance to the electronic industry. Broadly speaking, PGMs are extracted in minute quantities from a limited number of ores, found mainly in South Africa and Russia. As the PGMs are both costly and almost indestructible, they are usually recycled from various forms of scrap. In other words, the recycling of the PGMs is an essential factor in the overall management of the PGM economy. In addition, the ever-increasing user areas have created renewed interest in the search for new sources or deposits of PGM, which in turn requires an in-depth knowledge of its characteristics. In this work, the emphasis is placed on the need to analyze the composition and microstructure of blast-furnace slag for recovering PGM metals. In other words, chemical composition, surface analysis and microstructure analysis of the DC arc furnace slag have been carries out. The aim is to provide a detailed analysis of this material for anyone with an interest in gaining further knowledge of its specific content for recovering PGMs."

Jan 1, 2014

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Brian Hart, Rong Fan, Roger Smart, Andrea Gerson, Ning Xu

A complete strategy has been developed for identification of the reasons for losses in recovery and/or grade, due to changes or complications in mineralogy and in mineral surface conditioning, and their subsequent correction. The sequence of methods starts with comparison of mineral phases between QEMSCAN/MLA (compositional) and Rietveld XRD (crystalline diffraction) with bulk assay reconciliation. This methodology has recently led to identification of unrecognised amorphous content (12-40 wt.%), previously attributed to crystalline phases, in the fine fraction (<35 µm) of some problematic flotation feeds. Attached amorphous silica, talc- and chlorite-like fines have direct influence on the hydrophobic/ hydrophilic ratio on value mineral surfaces adversely affecting flotation. SEM/EDS is used in the backscattered imaging mode to determine possible problems with liberation (e.g. remnant local locking), not detected in standard liberation analysis, resulting in gangue flotation. EDTA extraction is used to assess bulk feed pre-oxidation and sequential oxidation product loading through the circuit. Changes in circuit solutions are assayed with speciation modelling of precipitates and potentially adsorbing species. ToF-SIMS with principal component analysis is then used to correlate surface species with specific minerals and can be used to assess the effectiveness of specific reagents particularly collectors. This approach identifies unwanted activating species and interference with value surfaces by adsorbed hydrophilic ions, precipitates and fine particles. When the interference or ineffective reagents are specifically identified, remedial action can be targeted. This method has identified residual talc-like layers (<10 nm thick) inducing gangue flotation of pyroxene and chromite in PGM flotation. Recent case studies of application of the full methodology to losses of molybdenite at KUCC and to sphalerite activation in the Cu/Pb circuit at Brunswick Mines with remedial action are discussed.

Jan 1, 2014

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By Thomas Mütze, Anja Hirte, Ursx Peuker, Thomas Kuhn

"The comminution behavior of two ferromanganese nodules samples of the equatorial northeast Pacific has been examined as a basis for the separation of two kinds of metal-rich layers. Those layers were finely grown together during nodule formation and are one reason that the exploration of deep-sea minerals calls for the development of new mineral processing concepts. Therefore fundamental analyses of the fracture behavior have been made under compressive and impact stress. Further experiments took focus on the crushing behavior in a jaw crusher and a small scale impact crusher as well as the milling behavior in a dry vibrating mill, a wet planetary ball mill, and a wet agitated ball mill. The comminuted products were characterized by PSD, particle shape, particle density, and porosity. The experiments show a low stress resistance of the ferromanganese nodules. Compared to compressive stress, impact stress turned out to be the more effective for crushing. Both samples showed no significant difference in the comminution behaviour which makes differing mechanical treatments unnecessary. In both cases particle sizes below 1 µm were achieved by wet grinding. This particle size is necessary to separate the two kinds of metal-rich layers which is part of continuative studies."

Jan 1, 2014

By B. McFadzean, S. Geldenhuys

"Dynamic froth stability tests have found widespread application to quantify froth performance. However, little to no attention has been given to scale parameters in the performance of these measurements. One of the most frequently changing scale parameters in the laboratory scale is the column diameter as this directly influences the amount of material needed for testing. Four different column diameters (50, 100, 200 and 300 mm) were used for this study. Column diameter experiments were done on an industrial scale by means of manual tracking of froth growth versus time. An increase in measured dynamic stability was seen with increasing froth column diameter, which reached a limiting value at large column sizes. It is thought that this behaviour is controlled by the differences in drainage rates of the bulk froth compared to froth in contact with the wall. The column diameter required to represent full-scale froth stability is proposed. A ratio of column surface area to total bubble surface area was used to correct for different column diameters.INTRODUCTIONThe froth phase in flotation contributes significantly to the overall performance of the process (Zanin, et al., 2009). Numerous parameters have been investigated to quantify froth performance, most notably froth recovery (Feteris, et al., 1987; Seaman, et al., 2004; Vera, et al., 1999). Experimentally gathering data to determine froth recovery is challenging and for this reason froth stability has been highlighted as a possible alternative.Froth/foam stability is defined as the time of persistence of the froth/foam and is affected by numerous factors, such as: drainage of the liquid in the lamellae (gravitational and capillary), viscosity at the bubble surface, thickness of the electrical double layer and gas diffusion through liquid films caused by pressure differences between bubbles (Aktas, et al., 2008; Beneventi, et al., 2001). It is well documented in both froth and foam literature that froth/foam stability will heavily influence the performance and appearance of the froth/foam phase (Ata, 2012; Farrokhpay, 2011; Weaire, et al., 2005). Experimentally this has been explicitly proven as an increase in froth stability, characterised by water recovery, usually results in an increase in both valuable mineral and solids recovery (Wiese, et al., 2011; Banford, et al., 1998)."

Jan 1, 2018

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018