Search Documents

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is main parameter for precipitate flotation in pilot or industrial scales. The knowledge of aggregate structure can lead to better understanding and control of many solid-liquid separation processes (sedimentation, filtration, thickening and flotation). Many authors highlight the importance of structural properties (i.e. floc density) for different industrial applications.This approach was applied to achieve the flotation of molybdenum precipitate obtained with organic collector a- benzoin oxime for molar ratio 1:2. Flotation tests were carried out at lab and pilot scale with rigorous control of the size distribution of bubbles and the values of dissipation energy in the systems.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions, which were deduced from experimental data of laser sizer devices and optic microscopy pictures of precipitate. The boundary fractal dimensions Df of large aggregates allows the detection of a structural scaled organisation of the precipitate flocs (elementary germs-microflocs-flocs). The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with structuration or breakage phases.The destruction process characterised by a fractal dimension Dg controls the final size distribution. The floc destruction occurs for the lowest values of the dissipation energy (0.02 – 0.05 W/kg). The relation between Dg and the system dissipation energy Et (for various energy E dissipated in the agitation cell) involves the different breakage mechanisms of aggregates in function of the aggregation bonds (Fig. 1).Besides, the destruction of floc produces very fine particles (elementary germs or/and microfloc according to E), and thus induces the difficulties of bubble-particle attachment during the precipitate flotation in column. Yet, very small bubbles, which increase the collision probability, would make the flotation feed rate decrease. The optima ratio between superficial gas and feed velocities are determined for bubble size and flotation results control at pilot scale. Thus, it is possible to providing the catastrophically changes of precipitate column flotation by using the following established experimental relation: the mean diameter d of the flocs under the action of dissipated energy Et follows a power like law (d~Et -0.5). This allows estimating the size distribution of flocs for the E values which can appear in column."

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

"INTRODUCTIONThe grinding rate prediction scheme makes use of the energy spectra output from the DEM simulations and the statistical quantification of material strength, which can be done using the drop-weight tester or some other similar equipment. The prediction scheme is evaluated using milling experiments performed under well-defined conditions.MATERIAL STRENGTH QUANTIFICATIONUsing the drop weight test machine, particles of a wide size range were broken singly using different energy inputs. A characteristic equation key to milling rate prediction that relates the probability of fracture with energy input and number of impact attempts was obtained and is stated as follows:"

Jan 1, 2003

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Vishal Shukla, Ashok Kumar, Manas Ranjan, D. Chakraborty, Narayan Sharma

Jigging has a very important role in mineral processing Industry. Upgrading of Iron Ore by jigging has been an emerging trend. A detailed investigation is carried out to understand the influence of Jig feed granulometry and bed height during jigging operation. Noamundi jig plant data shows that variation in jig feed granulometry, feed quality and bed height are major contributors to fluctuation in jigging performance. At Noamundi the feed size (-10.0+0.5mm) fraction is used for fines jigging operation. To understand the effect of granulometrey on jig plant performance such as yield, separation efficiency and Fe recovery. In this context The performance of jigging was evaluated by daily average data from jig operation was used to study the influence of feed distribution on jigging performance .Coarser fraction (+6mm) has a positive influence , whereas fines fraction (-0.5mm) tends to lower performance . During Jigging rearrangements of Particles takes place due to an alternate expansion and compaction of Jig Bed .These particles are arranged by increasing density from top to bottom. During the particle stratification, Jig bed physically cut at desired horizontal particle density plant to separate the desired product. Investigation shows that optimum bed height is required at different Jig feed quality to achieve desired product quality, maximum separation efficiency and Fe recovery. This Paper will illustrate role of granulometry and Bed height control on Jigging plant performance.

Jan 1, 2014

By Fedotov Pavel

One of the efficient means of ore disintegration during the processing is its volume breakage in such machines as roller-presses. Up to date neither the ore disintegration mechanism in roller-presses nor the reasons of their high efficiency are thoroughly investigated. In this work, the mathematical model of Finite Element Method of bad material disintegration in roller-press is discussed. The mechanism of the interparticle ore disintegration is traced.

Sep 1, 2012

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Lutz Rolf, Halit Z. Kuyumcu, Salas Cazón. Milton A.

Aim of experimental investigations was the mathematical description of the abrasion process running with a single particle stress. This is on the one hand the basis for the physical interpretation of the process, on the other hand the base for the simulation of abrasion processes carried out in technical scale. With this investigation for the first time the influence of the particle shape changing with increasing abrasion progress was quantitatively described. This influence affects itself particularly strongly on break-fresh particles up to an abrasion degree of approximately 10 to 20%. This is for the description of technical processes the most interesting area.

Jan 1, 2003

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By G. N. Jadhav

In India, bauxite deposits are concentrated in Central India, Western Ghats and Eastern Ghats. Bauxites from various regions in Gujarat were identified during the present investigations of geochemical mapping. Different types of Bauxites samples were collected from Kachchh, Jamnagar, Porbunder, Junagarh, Bhavnagar and Amreli areas of Gujarat state and were studied in detail for their geochemical signatures to plot the data on Geochemical map. Raw bauxites were characterized by using powder XRD, XRF, ICP and optical microscopy techniques (with the help of Model microscope having both transmitted and reflected light setups) and were later examined to grade their quality. Most of the bauxites from Kachchh region were of high-grade (gibbsitic) type; while those of Sourashtra region were of low-grade (lateritic / calcitic) types. Most of these bauxites were either of ferruginous/lateritic or of calcareous/calcitic types. Based on the mineralogical composition, such as gibbsite, hematite and/or goethite, Kaolinite and calcite minerals present in particular bauxites, the deposits were graded. Finally, the Geochemical mapping of Bauxites for Gujarat region was prepared and discussed.

Sep 1, 2012

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St. Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By Dave Deglon

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The WCMPF was established in 1989 with the aim of improving mineral processing education in the Western Cape. Since its inception the WCMPF has had a number of successes in this area, especially in improving the quality of mineral processing practical training. In addition, the WCMPF has played an important role in promoting liaison and interaction between tertiary educational institutions teaching mineral processing in the Western Cape. Over the past decade the WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. This paper presents an overview of the activities of the WCMPF and attempts to encapsulate the ‘lessons learned’ from over a decade of successful functioning as a collaborative educational initiative in mineral processing.

Jan 1, 2003

By A-M Ahonen

The paper discusses the experiences of a fast-track curriculum designed to provide the industry with engineers capable of working in minerals processing industry. The course has been done once before and the second course has been started. Students chosen have graduated from other fields of engineering. For the first course, twelve students were chosen from 152 applicants and for the second the twelve students were chosen from 96 applicants. The basic idea of the curriculum is to alternate between theoretical studies at the university and working experience periods at industrial sites. In addition, there are several one week assignment tasks at industrial sites. The theoretical periods are six to eight weeks long and there are three of them. During the first period, the teaching concentrates on unit processes and their chemical and physical background. The theme of the second period is mineral engineering systems; flowsheet development, process dynamics, control systems etc. The last theoretical period teaches environmental issues, leadership, project work and other similar topics. Each of the theoretical periods ends with an assignment week at industrial sites. The assignments are designed to wrap up the teachings of the period. For the industrial periods, the students are given learning goals, which have been discussed and designed with their industrial mentors. They are required to find relevant literature, make experimental designs, implement those designs, present the data, and make conclusions of their results. During these periods, a weekly meeting over the Internet is compulsory. Keywords: mineral processing, flowsheet development, process dynamics, control systems, constructivism, zone of maximal development, Vygotsky

Sep 1, 2012

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003