Search Documents

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper, molybdenum, rhenium and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2014

By Z. G. Song

As a kind of complex physicochemical process, grinding would affect the subsequent mineral processing such as flotation considerably. In this study, the effect of wet grinding on malachite and calcite flotation using sodium oleate as collector was studied. And the mechanism of the effect of grinding was investigated. Laboratory scale grinding and flotation testing of malachite and calcite samples were performed. Different grinding media were used, including steel balls and zirconia balls. It was the aim of this work to study the effect of grinding on the pulp chemistry paying particular attention to flotation recovery. The effect of grinding media and different addition location of sodium oleate on malachite and calcite flotation was studied. The methodology used in this project involved grinding the ore with and without the addition of sodium oleate in mill, measuring the pH and metal ions produced by minerals after grinding, adding various quantities of sodium oleate and determining the copper recovery. The presence of species of products on the minerals after grinding was probed using X-ray photoelectron spectroscopy (XPS), and the metal ions produced by minerals after grinding were measured by atomic absorption spectrometry (AAS). It is showed that the mil-ling environments evaluated significantly affected the flotation of malachite and calcite. This study also discusses the effecting mechanism of grinding environment on floatability of malachite and calcite.

Jan 1, 2014

Certainly, one of the core processes for the recovery of fine magnetic susceptible iron ore particles, mainly hematite iron ores, is the wet high intensity magnetic separation or WHIMS. This paper outlines a variety of recent developments and innovative process designs in the JONES® type WHIMS. It highlights the latest examples of flow sheets in terms of the diversity of combined rougher, scavenger, cleaner stages and adds to this the new more advanced JONES® type WHIMS equipment technologies like the HIGH FLOW ? HF, the QUATTRO ? Q and the SPLITT OPERATION ? SP. As a result of the increase of the capacity and magnetic intensity, the specific production cost could be decreased. The high worldwide acceptance for this continuous development testifies for the success and state of the art technology.

Sep 1, 2012

By J. Y. Tian

In view of the fact that many domestic iron ore-dressing plant applying flotation cells in the re-verse flotation, to improve the technical level of magnetite reverse flotation, we apply such a technological process of one stage rougher and two stages scavenger flotation column respectively. The middling from the two stage scavenger process are returned to magnetic separation for condensing. By contrast, the technological process of one stage rougher and one stage cleaning flotation cells is made up of by multi-magnetic separation and magnetic middling regrinding separations. It has been proved that the flotation column we offer can simplify the technological process structure, obtain advanced technical indexes, run the system smoothly, reduce energy consumption, and be environ-mental friendly.

Jan 1, 2014

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

By V. Panayotov

Slag and by-products of metallurgy bear valuable components and their processing raises an in-creasing interest. Coke and iron have to be separated and other components have to be depressed, in order to obtain sellable high quality copper concentrates. Use of classical mineral processing technologies, such as magnetic separation, sulphidization, hydrometallurgy, etc. yields copper concentrates with grade of 4%~6% Cu. Copper is lost in tailings and the whole technological cycle is low profitable. Technology proposed applies an electrochemical treatment of the industrial water entering the flotation cycle. Iron and iron compounds that do not bear Cu, coke and gangue materials are depressed during the copper flotation. Copper concentrate of grade of 9.8%~10% Cu is obtained at simultaneous increase of Ag recovery by 8%~10%. As a result company profitableness is increased. Technology proposed is easy to implement, it does not require changes in the existing technology flow-sheet, and additional investment is low. The flotation process can be aided by a specially developed system for real-time analysis of the obtained copper concentrate which allows in-time corrections in the flotation parameters and entire process control. Applied flotation schemes, technological parameters and results obtained are described.

Jan 1, 2014

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By G. Jenny

The particle size distribution of ground minerals is of decisive importance for downstream processes like floatation, separation, drying or others. In order to optimize the process efficiency on one hand and the final product quality on the other hand an early control of the grinding or classification stage is essential. The ultrasound based particle size analyser OPUS is capable of performing on-line particle size distribution (PSD) and solid content measurement of mineral slurries such as iron ore, copper ore, fluorspar, or quartz sand and alumina directly in heavy and rough process environment. The instrument provides a PSD of 31 size classes and can be applied for particles from nanometer range up to several millimetres. Arbitrary interpolations in between the 31 measured points are available. Typical residue values show an excellent agreement to off-line particle size analysis methods such as e.g. sieve analyses or laser diffraction. OPUS is designed as rugged in-line probe made from stainless steel. The applied technique is independent of product flow dynamics, contamination, optical properties, vibrations, pressures or changes in solid concentrations. The instrument provides all data on the system?s PC or on the process control system by a variety of interfaces.

Jan 1, 2014

By Sepideh Javanshir

The process of liquid?liquid extraction of gold from chloride solution is complicated by the presence of many variables acting simultaneously in an unknown non-linear fashion for the determination of the final extraction efficiency. In practice, it is quite difficult to develop a model for predicting various properties of such process. Therefore, an alternative approach based on Artificial Neural Network (ANN) is considered to assist in the simulation process. Artificial neural networks (ANN) are powerful tools that can be used to model and investigate various highly complex and non-linear phenomena. This paper presents application of Multi-Layer Perceptions (MLP) to construct relationship that will be employed to develop a quantitative method for the estimation of the extraction efficiency as a function of hydrodynamical parameters such as stirrer speed, [AuCl4]- and DBC concentration, organic and aqueous flow rate. The model is shown to be in excellent agreement with the experimental data (R2 value for training and testing data was 0.9992 and 0.9915 respectively). Therefore, it can be used to optimize the parameters of liquid?liquid gold extraction with dibutyl carbitol (DBC).

Sep 1, 2012

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By R. M. Zhao

The process conditions and mineral characters of cleaning separation stage in magnetite concentration plant are studied in the paper, and the affecting factors and the methods to increase the concentrate grade are analysed and given. The BKJ cleaning special drum magnetic separator is developed specially for the cleaning stage according to process conditions and mineral character. The separation mechanism, structure characters, separation process and excellent adaptability of BKJ special magnetic separator are described. The results in Zhangjiawa Concentration Plant show that the BKJ special drum magnetite separators play an important role in increasing the concentrate grade and improving the economic benefit.

Jan 1, 2014

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012