Search Documents

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By Xiaoming Wang

This paper describes a new magnetic separator integrating dynamic permanent magnetic force, gravity and flow dynamics to enhance the quality of the iron concentration. This equipment can increase the grade of concentrate by controlling the formation of magnetic agglomerations to reject most gangue. Test results indicates that the compound force field separator can be applied in improving the quality of iron concentrate and has a wide range of potential market applications. Keywords: magnetic separator, compound force field, rotating magnetic system, magnetite concentration

Sep 1, 2012

By M. K. G. Vermaak

Kimberlite weathering has been a topic of ongoing research within De Beers for many years. Using kimberlite weathering as an alternative to crushing has many advantages e.g. power and reducing diamond breakage. Weathering could also possibly be used in conjunction with crushing just to weaken the material and reduce power consumption. These forces have driven current research to investigate whether kimberlite weathering could be utilised for these reasons. Weathering in this context does not refer to weathering over long period of time but rather to disintegration of the material in aqeous media in relative short time periods. Previous published work discussed that the presence of smectite renders kimberlite weatherable and that the amount of smectite determines the rate of weathering (Morkel and Vermaak, 2006). The current work investigates whether cation ex-change or the adsorption of organic species in the smectite interlayer could influence the observed weathering behaviour. The results show that cation exchange does take place in the presence of cation species and that the weathering behaviour can be drastically improved with especially Cu2+ cations. Concentration and time effects of the weathering was also investigated. Weathering tests with organic species such as ethanol, methanol, edta, pentanol, butanol, acetic acid and oxalic acid was performed. The results show that organic species does improve weathering but under these testing conditions was not as effective as cations.

Jan 1, 2014

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By A. P. Das

Biomining technology focuses on achieving effective recovery of precious metals from their ores and concentrates using microbial techniques. Biomineral extraction of manganese from low-grade manganese ores using bioleaching was investigated in this paper. Five fungal strains were selected for screening of bioleaching of low-grade Mn ore collected from Sanindpur iron and manganese mines, Koira Sector, Keonjhar, Odisha, India. A fungal strain, Aspergillus niger was selected as it showed high efficiency of manganese leaching. Growth of the fungus was determined in terms of sbiomass dry weight and the final pH was monitored. The selected fungal strain was used for bioleaching of low-grade manganese ore of -150µm size particle size at 2 % pulp density with 2g/100ml sucrose concentration for duration of 20 days. About 60 % of Mn bioleaching was obtained with A. niger. The fungal species proved to be useful for manganese biomining.

Sep 1, 2012

By B. Tora

The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. The essence of this method consists of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. The research equipment designed specially for this project is described New method of grindability measuring completes standard Hardgrove method withdrawing its faults: ? bigger (c.a. 10 times) and more representative sample is used; ? the milling process is carried out in close circuit (similarly to the industrial condition); ? energy consumption of the milling process is determined for three samples, which differs in grain size. The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. This method allows us to determine energy consumption of the milling process. The essence of this method consist of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. Our results will complete the Hardgrove method and will help us to better characterise coal. At the same time investigations in industrial scale are carried out. These investigations will verify this new method. Also a new mathematical model of the milling process is being elaborated. It will be used to predict behaviour of coals in industrial conditions.

Jan 1, 2014

By X. Q. Ma

The beneficiation test on low grade phosphate ore from a state of Russia is carried out. The rougher-cleaner ? re-cleaner system is used in the flotation process, The fineness of grind is 39.07% minus 200 mesh. The result indicates that concentrate containing 31.25% P2O5 can be obtained from the flotation feed assaying 6.18% P2O5, with 93.54% P2O5 recovery. The test result is also a guideline for further development of some currently operated phosphate beneficiation plants.

Jan 1, 2014

By József Faitli, Imre Gombköto, Barnabás Csoke, Tamás Magyar, Beáta Oláh, Sándor Nagy

"Raw materials are among the main building blocks of a growing economy. Without raw materials, no matter whether it is primary or secondary, production is not possible. Products with high added value require special materials. Recently, worldwide production of some important raw materials mainly comes from a handful of countries, for example: China (Rare Earths Elements (REE)), Russia, South Africa (Platinum Group Elements (PGE)), Democratic Republic of Congo (Cobalt), etc. In the EU as well as in Hungary, the importance of the so called 14 critical raw materials has been recognized. Within the frame of the TÁMOP-4.2.2.A-11/1/KONV-2012-0005 - CriticEL project, the Institute of Raw Materials Preparation and Environmental Processing in cooperation with the Institute of Mineralogy and Geology of the University of Miskolc are working on the exploration of the primary and secondary sources and developing innovative preparation technologies of critical raw materials in Hungary. The research work showed in this article, focused on the recovery of critical materials from LCD TVs and monitors. There are high deviations in different literatures regarding to concentrations of critical elements in displays (e.g.: indium), probably because of the differences in production year, producers and recovery technologies. During the research - described in this study - a well specified sample of quite large amount of displays had been used. The exact place and shape of the ITO (indium-tin oxide) layer were determined by SEM analysis. The applied preparation technology was developed based on the results of our investigations and by technologies found in the literature. The developed process accomplishes two main parts: the mechanical preparation (mainly the liberation of different display layers, removal of liquid crystal) and the acidic dissolution of indium."

Jan 1, 2014

By A. K. Suri

India plans to increase the nuclear power share in overall energy-mix to about 30% by 2032 using both indigenous and imported reactor technologies. In the immediate time-frame, it is envisaged to generate 10000 MW electricity by PHWR technology by 2020 using indigenous uranium resources. This necessitates setting-up of new uranium mills and augmenting the existing resource, mining and milling capacities. This paper describes the current status and future R & D needs towards achieving the targeted demand of yellow-cake. Keywords: uranium, hydrometallurgy, leaching, yellow cake

Sep 1, 2012

By D. W. Feng

Thiosulfate leaching has been considered as the most promising alternative to cyanidation for the recovery of gold from ores. The chemistry of the ammonia-thiosulfate-copper system is complicated due to the simultaneous presence of complexing ligands such as ammonia and thiosulfate, the Cu(II)-CU(I) redox couple and the stability of thiosulfate in solution. However, acceptable gold leaching rates can be achieved by maintaining suitable concentrations of thiosulfate, ammonia, cop-per and oxygen in the leach solution. The leaching of gold in thiosulfate solution is an electrochemical reaction involving the oxidation of gold to gold thiosulfate and the reduction of Cu(II) to Cu(I). Previous studies have shown that the reaction rate of gold was much higher in the presence of am-monia thiosulfate than corresponding sodium thiosulfate. This indicates that cations may affect the anodic oxidation of gold in thiosulfate solution. The present study utilises electrochemical tech-niques to study the anodic oxidation of gold in thiosulfate medium in the presence of the different alkali metal and alkaline earth metal ions. It has been shown that the presence of the heavier cations such as potassium, calcium, and caesium enhance the oxidation of gold in thiosulfate solution. Leaching tests also indicated the improved recovery of gold from a sulfide ore with the addition of heavier cations. XPS results demonstrated that the binding energy for gold shifted to lower values in the presence of the heavier cations, indicating the ready formation of ion-pair with gold thiosulfate at the gold surface during adsorption.

Jan 1, 2014

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By Z. H. Xu

Flotation as a versatile multiphase separation technology has been practiced for more than 100 years in coal and mineral processing. Although effective over a wide particle size range, flotation for mineral separation has been largely understood as an art rather than a science, treating the flotation system as a black box. With rapid progresses in microscopic technologies coupled with high speed video recording and imaging analysis, ingénue design of visualization systems has made it possible to understand fundamentals of flotation by visualization. In this presentation, the state of the art where visualization plays a key role in advancing our fundamental knowledge of flotation will be reviewed. The areas to be covered include characterization of bubbles (shape, size, velocity and sol-ids loading) in a running flotation system, either column or mechanical cell, bubble-solid attachment, hydrodynamic cavitation in fine particle aggregation and flotation, froth imaging, particle-particle interactions by zeta potential distribution measurements, and heterogeneous gas nucleation by atomic force microscope imaging. With these capabilities, critical roles, good or bad, of ore proper-ties, solution chemistry, slurry hydrodynamics, and operation variables in flotation systems as applied to mineral, coal and oil sands processing were clearly elucidated.

Jan 1, 2014

By V. G. Minenko, V. A. Chanturiya, A. L. Samusev

Eudialyte is one of perspective resources of zirconium and other rare earth elements (REEs). Large reserves of eudialyte concentrated in the Murmansk region of the Russian Federation. Usually, technologies of REE treatment include the decomposition of eudialyte concentrate in different acidic, extraction and utilization of all components. The main problems in the leaching of eudialyte include are: the formation of an unfiltered silicon-containing gel; low recovery of REE; difficulty extraction of metals from the productive solution; high aggressiveness of the reagents. One of the promising trends of intensification of the processing of hard-to-degrease rare metal raw materials is the use of energy methods for affecting mineral suspensions. These methods make it possible to increase the efficiency of break up fine-dispersed mineral complexes and extracting micro- and nanoparticles of a valuable component in subsequent deep processing. The purpose of this work is to investigate the effect of energy impacts on the nitric acid leaching of eudialyte concentrate. Experimental studies were carried out in a developed laboratory facility that makes it possible to evaluate the effect of electrochemical, ultrasonic and combined effects on the leaching of zirconium and REE from eudialyte concentrate. The studies carried out on the samples of eudialyte concentrate with the size class of -0.315 + 0.063 mm showed that the use of electrochemical and acoustic effects increases the extraction of ZrO2 in the production solution in 1.6 - 2.5 times, REE in 1.3 - 2.2 times, respectively. An analysis of the microstructure and phase composition of the surface of the eudialyte concentrate showed that the intensification of the leaching process is due to surface cleaning from the silicon-containing gel, as well as the opening of capillary channels and microcracks, which accelerates mass-transfer processes. The results obtained open wide opportunities for creation of modern and effective technology of processing of eudialyte concentrate, producing high-quality zirconium products and REE.

Jan 1, 2018

By Graeme Lamson, Rene Dobbe, Merle Kalstrom, Janice Baron, Robert Thorpe, Chris Martin, Snezana Bajic, Amanda Palko

"This paper presents early results from a case study at the Mount Polley porphyry copper mine in British Columbia, Canada. Daily mineralogical data was acquired and reconciled with daily plant assay and recovery balances to interrogate the mineralogical controls on plant performance. After commissioning, the Minesite machine operated smoothly and reliably, creating daily data to generate mineralogical balances around the circuit for a period of several weeks. The key data, on final products were produced within 13 hours of the end of the respective operating period. The resulting information allowed for a greater understanding of the opportunities and limitations of the Mount Polley metallurgy. In this paper, how this information can be used to help long term strategic planning for the operation, as well as mine planning and production forecasting and the fine tuning of day to day mill operations is described. Early data available at the time of preparing this paper indicated that roughly 40% of the sulphide losses, or 32% of total copper losses existed as low grade inclusions in +75 micron tails. This represented the dominant form of long term copper losses, demonstrated repeatedly in the routine analytical data. However, on a day-to-day basis, the amount of copper present as chrysocolla is the major driver behind variations in total copper recovery. The degree to which this influences mill recovery is valuable to the geologist or mine planner. As they are armed with mineral speciation information for future ores, this will allow for improved mine planning, prediction of copper recoveries and production forecasting. The data was also started to find value in the mill by showing what caused sulphide losses. In the roughers, for example, the data showed poor recovery was the result of poor flotation performance and not any changes the speciation of copper sulphides or their liberation characteristics."

Jan 1, 2014

By Lilong Huang, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Graphite is the key raw material of new carbon materials such as graphene and spherical graphite. The size and completeness of graphite flakes directly affect the performance of new carbonaceous materials.The research aims to increase the yield of large flake graphite by way of preventing the flake graphite from being damaged during the grinding process. A series of grinding and flotation studies on the flake graphite samples of Yichang in Hubei Province were carried out by vertical stirred mill . The damage coefficient L characterising the degree of graphite flake fractured and corresponding formula was proposed to determine the quality of the grinding and grinding of the flake graphite. The way the damage coefficient L of graphite flake would be affected if with different mill, different media material and size, stirrer speed were investigated. The test results show that vertical screw stirred mill helps the protection of large flake of graphite as well as the graphite liberation. When grinding to the same fineness, the damage coefficient L of graphite flake is 1.20 for vertical stirred mill, while the damage coefficient is 2.93 for ball mill. Minimum damage coefficient of graphite flake was obtained when using 6 mm polyurethane coated ball as grinding media, under the condition that rotation speed of the stirrer within the range of 100~130r/min. The grade of graphite in the concentrate floated from the ground product was 94.16%, the rate of recovery for graphite was 94.66%, and the content of +0.15mm was 54.83%.1 INTRODUCTION Flake graphite is a very important non-metallic mineral[1,2],and due to its special flake structure, the greater the scale and the higher the C grade, the value of its application is larger too. Therefore, in the grinding of graphite sorting process, We should minimize the destruction of graphite scales.. In this paper, graphite mine in Yichang, Hubei Province was used as the raw material for the study. Rough concentrate with C-grade of 36.49% was prepared by rough grinding and coarse separation. Then a series of grinding and flotation studies on the rough concentrate were carried out by vertical stirred mill , which aims to increase the yield of large flake graphite and to provide technical support for improving the beneficiation process of graphite ore."

Jan 1, 2018

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By N. Vorob?ev-Desyatovskii

The process of gold(I) adsorption on activated carbon (AC) from aqueous Na[Au(CN)2] and the state of the adsorbed gold cyanide complex on the adsorbent surface was investigated by photometry, XPS, XANES methods. By DFT method, quantum-chemical calculations were performed of the gold cyanide species on activated carbon surface. It was established that the binding of gold(I) with the surface of carbon involved several simultaneous processes governing the selective adsorption of gold(I) from the cyanide solutions.

Sep 1, 2012

By J. Y. P. Leite

In the Borborema Pegmatitic Province (Brazil) exploitations of several minerals are conducted by small producers. They use traditional techniques of gravity concentration in small-scale plants as jigs and vibratory tables. During decades the mining activity generated tailings with economic interest in particularly columbite-tantalite. Samples collected in tailing piles of a gravity plant were characterized in mineral composition, which shows in the heavy fraction the minerals spodumene, columbite-tantalite, ilmeno-hematite, garnet and cassiterite. The light fraction presents quartz, feldspar and muscovite. The degree of liberation of spodumene and columbite-tantalite were determined using optical microscopy that presents liberation in 100 µm (90% to columbite-tantalite and 100% to spodumene). Centrifugal concentrator Falcon SB-40 was used for concentration of these minerals and presents 65% recovery in mass to two stages with mass reduction about 85%.

Sep 1, 2012

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012