Search Documents

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By H. K. Taylor

Ore reserves are inadequately defined. Geological reconnaissance and pre-feasibility mining work generate a broad range of valid tonnage estimates, many published for the benefit of various interests, who may view all figures as reserves. This work reviews the regular estimation of tonnages, grades and relevant factors for single deposits. A consistent framework of definition is suggested which, by conforming to the known structures of feasibility studies and long-range plans, avoids the pitfalls of over-categorisation and of unrealistic promises. Applications are based on North American experience but are intended for general use

Sep 1, 1991

By D Macdougall, J Otto

The financing of large mining projects in developing countries is often achieved, at least in part, by limited-recourse financing methods. Financing agreements are affected by the basic accord that is struck between the host government and the sponsors of the project. It is concluded that governments and project sponsors should take into account the requirements of lenders when structuring such mineral development agreements to maximise the potential for attracting project financing. Lenders are likely to be most interested in aspects such as fiscal arrangements, calculation of taxable income and general accounting rules, royalties, transferability of payments/dividends overseas, corporate structure and control, staged development, financing, loan support and state guarantees/approvals, political risk, provisions for default, product marketing, settlement of disputes and environmental issues

Aug 1, 1994

By P. H. Morris

The exponential delta profile equation matches the profiles of a wide range of coal and metalliferous subaerial tailings deltas well, but the original model implies unrepresentatively low solids concentrations. A revision, based on analysis of the governing equations of mobile bed flows with high concentration values, has shown that for exponential delta profiles to form there must be quasi-steady, slowly varying flow and slow deposition as well as tailings with a log-uniform sorting-parameter distribution. Deposition on tailings deltas is slow and the flow in many natural streams and, by analogy, tailings deltas is quasi-steady and slowly varying; the assumption of such flow is justified by the strong congruence of the revised model and the available data. The predictions of the theoretical model are essentially unchanged but concentration and flow Froude number are now not explicitly limited

Jun 19, 1905

By R. K. Dunham, D. J. Reddish, X. L. Yao

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 10 refs. The integrated approach combines a powerful ground movement prediction program with a knowledge-based expert system. ESDAS (Expert Structural Damage Assessment System) was developed to evaluate mining subsidence damage in the form of risk and in terms of the three vital contributing components (mining factors, site factors and structural factors). Using a certainty factor risk assessment technique, the system can be used to predict the likely damage to a particular structure subjected to mining subsidence. A previously developed powerful ground movement prediction program, SWIFT (Subsidence With Influence Function Techniques), has been combined with the expert system to allow the mining factor to be more accurately determined in a broader range of mining layout. Since SWIFT can be calibrated to any particular coal field using local subsidence data, it is believed that the integrated system could be used in any coal field worldwide for the assessment and control of mining subsidence damage risks

Dec 1, 1995

By M J. Thomson, P T. Burgin

The economic growth of Hong Kong and adjacent territories in Southern China is, to a considerable extent, dependant on air transportation, but the present Kai Tak Airport is incapable of expansion to meet future needs. After years of study, agreement was reached to build a new airport on the island of Chek Lap Kok, some 34 km remote from Hong Kong, with an ultimate capacity of 87M passengers and 8.9 Ml of cargo per annum. Apart from the building of the airport and its associated infrastructure (including a new town), other similar massive construction works have been necessary in the form of land reclamation from the sea and existing outer lying islands. The construction of bridges, tunnels, railways and highways are also an integral part of the project. The paper provides a broad overview of the concepts of the scheme (called The Airport Core Programme) and highlights some of the major operations and equipment being used in the projects, whose cost at 1992 prices was reckoned to he Hong Kong (HR)$l63hn.

Jan 7, 1997

By E. J. Bolitho

"The paper covers the activities of the Government Miners' Training-Schools. It argues that its success is proved by the steady demand for miners trained at the Schools; by the large numbers of ex-apprentices who hold responsible official positions in the industry; and bv the probable expansion of the organization in the near future to meet the never-ending call for trained personnel."

Jan 1, 1947

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

By J Parnell, B Manson

Bitumen occurs in the basins in reservoir sandstones, in veinlets close to hydrocarbon source rocks, in veins through lava beds and in sulphide-mineralised veins where it is closely associated with, but predates, the sulphides. The role of organic matter was probably in enhancing metal reduction by creating a low-Eh environment rather than in metal transport. Coeval euhedral quartz crystals or albite in sulphide-bearing carbonate veins provide evidence of an aqueous component to the hydrocarbon fluid

Aug 1, 1995

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By S. Kelebek, J. A. Finch, Zhenghe Xu, S. R. (Ram) Rao

To improve SO2 emission compliance, pyrrhotite from Sudbury copper-nickel ores is being depressed with DETA. To understand the mechanism of depression, the role of complexing in controlling metal-ion activation of pyrrhotite was investigated. DETA was found to remove Cu and Ni ions but leave hydrophilic ferric species on the pyrrhotite surface. The metal:DETA ratio appeared to be 1:2. Cu was more readily removed than Ni, but the combination of DETA with sulphur dioxide was equally effective for both metal ions. Certain combinations of DETA, Ni ions, xanthate and dithionite (S2O4) or dithionate (S2O6), as representative derivatives of SO2 in water, produced hydrophilic precipitates. These may enhance pyrrhotite depression

Jun 19, 1905

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By B. M. England, L. C. Mackey

Magnesia minerals are included in most iron ore sinter mixes to provide the MgO requirements of blast furnace slag. The properties of these minerals have an influence on the eventual sintering properties of the mixes. A detailed study was undertaken of serpentine and dolomite and the use of limestone, olivine and magnesite was also investigated. A consideration of particle properties indicated that as these materials calcine a reduction in size can occur together with cracking and changes in surface properties. These changes could affect the permeability of the sintering bed and sintering performance. Studies of sintering reactions showed that magnesium and calcium, formed from the calcination of dolomite, are extremely mobile before the formation of melt. Evidence suggests that the movement of these oxides into surrounding areas is via a solid-state diffusion process. The diffusion of Ca into the surrounding hematite particles is faster than that of Mg, resulting in the formation of dicalcium ferrite and magnetite or magnesioferrite, the last two subsequently being converted to dicalcium ferrite in the presence of Ca with removal of Mg from the structure as ferroan periclase. Studies of pilot-plant sinters indicated that reaction mechanisms formulated from the bench-scale studies were occurring in actual sintering processes. The differences in sintering reactions between dolomite and serpentine were considered to be the major cause of differences in the availability of lime for bonding phase formation. Pilot-scale studies indicated that the sintering properties of a mix containing dolomite could be improved by increasing the basicity of the sinter mix while keeping the MgO level constant

Jun 18, 1905

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By N. B. J. Kieser

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. Platinum-group minerals (PGM) in the enriched zone at Dust Mountain occur in two separate parageneses, the first representing primary magmatic PGM and the second primary magmatic PGM that have been reduced to alloys during serpentinisation. Minerals in the first group were unaffected by hydrothermal alteration on account of their textural setting or stable chemical composition. Despite substantial alteration of the serpentinised assemblage, most evidence points to the dominant role of primary magmatic processes in determining PGM occurrence. Several base metals have nevertheless been introduced hydrothermally. With respect to surficial dispersion the single most important paragenetic factor was the reduction of sulphides to alloys, rendering them more susceptible to mechanical erosion and less so to chemical leaching. The different textural setting of Pd-group and Ir-group phases results in different dispersion characteristics, with major implications for stream sediment sampling

Apr 1, 1994

By R. A. Ixer, R. A. Lord, H. M. Prichard, A. J. Boyce, P. McConville, C. T. Pillinger, I. P. Wright, J. Maynard

Analysis of 62 samples show that the sulphides throughout the igneous stratigraphy have a magmatic signature, with the exception of the uppermost gabbros and the lowermost basal thrust talc-carbonate lithologies. Mean delta-34S values for whole-rock samples from harzburgites, dunite pods in harzburgite, crustal dunites and wehrlites, the main and high-level pyroxenites and gabbros suggest that the primary sulphides derived their sulphur from a magmatic source enriched in 34S. This finding is compatible with the proposed origin of the ophiolite above a subduction zone. Values for pyrite mineralisation in the uppermost part of the gabbros are thought to result from precipitation from a seawater-derived fluid, while isotopically light sulphur in the basal thrust could have been introduced from underlying metasediments. The replacement of pentlandite by heazlewoodite has not led to sulphur fractionation

Jun 19, 1905

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905