Search Documents

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By R. Jacob

Mining has been around for a long time, and new deposits are being discovered continually but are becoming more complex for processing and typically sulfide in nature. Most of the large easy deposits with simplified and cheaper to process oxide material have been mined or the deposits are locked up with legal or social issues and may never be mined. It is common to see the mines today being evaluated to mine have little in oxides and have a sulfide component to the deposit. This creates a problem with explosives being selected for the mine because ANFO could cause a reactive ground issue. When evaluating the cost component of mining for future mines, ANFO is the go-to selected bulk explosive because of the cost and effectiveness. More work needs to be done by projects evaluating costs by properly testing the ground and water conditions to match the correct bulk explosive for the ground conditions of the mine. This will prevent a possible safety hazard and the best result for the mine.

Feb 6, 2023

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By DuPont Magazine

RBH Note: as stated many times in these articles, frozen dynamite was one of the greatest hazards facing the blaster. It wasn’t until the late 1920s that it was solved for good, with the introduction of nitrated ethylene glycol as a partial replacement for nitroglycerin in dynamites. The du Pont low freezing dynamites contained TNT, DNT, or nitro-substitution compounds of various sorts.

Jan 1, 2015

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By Kyle Apple

The following is a case study of how LuckStone Corporation improved their blast monitoring and documentation program. A number of resources already at their disposal have been utilized to improve the body of data collected from each blast. The tools being used include GPS, aerial photos, and a user-friendly push button format excel spreadsheet. The data collected include product by product records of materials used, distances to all concerned neighbors, seismograph data, etc: The spreadsheet has been designed to perform an ongoing analysis of blasting trends. The program has been carried out at a corporate level and is in use by blasters at each location. This paper addresses the advantages and drawbacks of this program. It also addresses the ways in which the various tools were integrated, Discussed as well is the need for simplicity when bringing “new” technology to the field and the steps taken in familiarizing the end user to changes.

Jan 1, 2001

By Dale Ramsey

During Phase IV of our Landfill Mine Stabilization project at a coal burning power generating station, it was determined that a coal barrier pillar separating two abandoned areas of the deep mine had to be breached prior to expansion of the ash disposal area. The proposed plan by the landfill design engineers involved using a high pressure jet cutting tool to cut a slot to allow water flow to an existing industrial waste water treatment facility. Our plan proposed using explosives to breach the pillar from the surface reducing earth disturbance in a high quality watershed while reducing the project cost and accelerating the project time schedule. Many issues surfaced with the proposed change of using explosives. There were a number of lessons learned from this case history and is the primary basis of this paper.

Jan 1, 2003

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

By Winfried Rosenstock, Hans-Jochen Blatte

"The guidelines of fire-fighting strategies have to be rewritten, latest since theYellowstone-Fire.CF- and S3- procedure are developed to achieve firelines of 500 ms/ h length and 100 mswidth per unit. Thereby two stretched charges burried in different depth and fired delayedin one round covering 50,000 ms2/ h with non-combustible, natural material (soil) at oncein seconds."

Jan 1, 1993

By Johan Gjødvad, Catherine Aimone-Martin, Charles Dowding, Mathias Jern

A residential structure adjacent to a quarry in Ohio was instrumented to record structure motions, resulting wall strains and existing crack displacements in response to close-in blasting within 82 m (270 ft). The project is a cooperative effort among international experts representing the European Federation of Explosives Engineers (EFEE) and ISEE supported by more than 21 persons from eight different countries to compliment prior work performed at the Aitik Mine in northern Sweden. The focus of this study is to compare blast-induced vibration measurements relative to regulatory compliance limits as a percentage of allowable velocities among eight different countries for a one-story residential wood-frame structure with a brick-and-mortar exterior and full basement. Participating counties included Austria, France, Germany, Norway, Sweden, Switzerland, the United Kingdom (UK) and the United States (US). Geophones were placed on the foundation and in the ground in accordance with each country’s regulations to record peak velocities as a function of frequency or distance to blasting. This study extends the work performed at the Aitik Mine to include interior corner geophones to calculate global wall strains and micro-m (micro-in) displacement gauges mounted over an existing drywall crack to measure blast-induced dynamic crack responses and climatological influences on daily opening and closing of a crack. Structure responses were documented for 68 blasts conducted north of the structure from February through September 2023 of which 17 blasts were selected for detailed analyses. The highest in-ground PPVs recorded were 43 mm/s and 59 mm/s at the NE and SW corners, respectively. Measurements from these blasts plotted within each country’s limits provided a comparison of stringency among the counties. The percentage of compliance limits among counties ranged from an average of 114% for the US, UK, and Austria limits to the highest of 585% for Switzerland. Despite these high percentages of compliance for all countries, the global tensile strains induced by these blasts were at most only 12 μ-strains and occurred with the highest velocity blast that exceeded each county’s limit. This high percentage of compliance and low strain level demonstrates the restrictive nature of the regulations studied. Peak dynamic crack opening and closing during blasting averaged 20 -m (0.0008 in) while the 12-hour weather-induced crack displacement during the time period over which blasting occurred averaged 200 -m (0.008 in) and the largest 12-hr change in crack width was 356 -m. This low level of crack response validates the observation that the studied regulations have highly conservative limits for cracking potential of standard building materials.

Jan 21, 2025

By Benjamin Cebrian

The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

Feb 1, 2020

By Tristan Worsey, Jhon Silva

The paper discusses a limestone quarry case study that looks at change in fragmentation due to using different charge sequences when using the regular rhythmic timing method.

Feb 1, 2020

By Tyler Rockley, Carla Reyes

Autonomous fragmentation measurement systems designed for shovels have been in operation for nearly two decades, however fragmentation systems capable of performing in the dynamic conditions of the front-end loaders (FEL) were only recently introduced to the market. This paper presents an in-depth evaluation of an automated digital fragmentation measurement system specifically designed to perform under the dynamic operational conditions of the FEL in two of Teck’s mine sites. As early adopters of this novel application, Teck embarked on a Proof-of-Concept (PoC) trial phase, defining a set of key performance indicators (KPIs) to qualify the performance of the digital solution in tough mining operating environments. The KPIs focused primarily on the hardware robustness, quality of image and segmentation, both day and night, availability of the system and sample ratio. The benefits expected from using this technology include increasing the safety of the current fragmentation measurement process, improving the quality of the analysis, increasing the sample representativeness, and using the attributes of the system to create an oversize detection alert to inform the loading operation process. A critical part of the evaluation was verifying the system’s effectiveness on the particle segmentation algorithm as this element often gets overlooked, especially when dealing with the large number of samples autonomous systems can generate; minor misclassifications due to inadequate segmentation are often dismissed as they might not be statistically significant, however systematic misclassifications can cause unacceptable deviation in the data and limit the intended application of the technology. The system’s performance was further validated through several tests that involved identifying objects of known sizes to ensure the reliability on the consistency of the particles’ segmentation.

Jan 21, 2025

By D J. McLane, J T. Rathbun, B T. Lusk

The dynamics of explosive detonations are understood, however recreating a real-world, full scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this paper is to better the understanding of how the waveform characteristics resulting from an explosive detonated within a shock-tunnel differ from those in an open-air arena test. The variables of comparison between an open-air arena test and those conducted within a shock tunnel are peak pressure, impulse, shock wave velocity, and cross sectional shape of the shock front. Understanding how these variables differ, tests utilizing a shock tunnel can be conducted with a higher degree of accuracy and repeatability.

Jan 1, 2013

By J. Mikhael Erekson, Connie Campbell Brashear, Brent Meins

Christmas morning 2020, an IED in an RV was detonated along an evacuated section of downtown Nashville, Tennessee. The blast damaged over 40 buildings, including AT&T’s Main Central Office and caused internet and cell outages across 1,200 zip codes for three days including the airport and EMS services. Published investigations by the ATF and FBI were inconclusive in determining the explosive composition and size. Video captured a large fireball that may indicate a fuel-air-mixture explosion which would create lower peak pressures than high explosives, but longer pressure duration and significant impulsive loading. Blast pressures were amplified by reflections in the urban environment bordered by the 8-story AT&T building and a row of multi-story historic buildings. Some structures had little damage as they were shielded from the blast pressure by closer buildings, and seemingly far-field structures contained damage from the pressure wave after multiple reflections and propagation through porous parking garages. Damage to the reinforced concrete frame AT&T building included snapped masonry ties, cracking and spall to the closest column, and vertical displacement of the elevator, even with the brakes applied. The historic structures directly across the street from the blast partially collapsed. Initial damage included complete failures of unreinforced masonry façades, broken timber beams, and uplifted roofs. Secondary, progressive collapse took place over months as the brick walls and weakened historic mortar could not resist typical wind and environment loads. One of the close historic structures was renovated in the 1990’s and structural retrofits to comply with building codes were required. The addition of steel columns and façade tie-ins improved survivability and it remained standing with a high percentage of the front brick intact. Generally, the observed blast damage was related to a structural component’s mass and flexibility. Internal timber framing was unscathed, but many steel studs required replacement. Glazing damage was observed several blocks away and many roof membranes were punctured by falling debris. Secondary damage from broken sprinkler lines and loss of environmental control often led to more costly repairs than the initial blast pressure damage. The proliferation of bomb-making knowledge leads to hundreds of bombings each year in the US. Building risk considerations should include explosive threats along with other hazards. ASCE structural standards and design manuals have been published to address these risks and may be useful guides for building construction.

Feb 6, 2023

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By TH Kleine, AR Cameron

Size assessment of fragmentation is all about estimating the population of fragment sizes in the rock pile. A knowledge of the size distribution of particles can be used in applications from evaluating the stability of a waste dump, to optimizing a blast design to achieve a required fragmentation, to on-line control of a crushing and sieving operation.

Jan 1, 1997