Search Documents

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Enver Alan

In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. S

Feb 1, 2020

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004

By Paul Downing

Anyone in business today knows how difficult and time consuming it is to keep abreast of new and revised federal regulations. Those in the explosives industry know that such a task can be next to impossible as the regulatory environment faced by those in the hazardous materials community continues to undergo a major overhaul following the events of September 11th, 2001. This paper will attempt to clarify today’s regulatory picture by identifying some of the regulatory “hotspots” and “pitfalls” that affect individuals and companies involved in the sale, transportation, distribution and use of explosives.

Jan 1, 2003

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By Kenneth Etschlager

The ISEE Blast Vibration and Seismograph Section provides a forum for the discussion of issues related to vibration and noise from mine, quarry and construction blasting. The section began as a Technical committee in 1995 to promote the accuracy of blasting seismographs. Currently five subcommittees exist within the section: Seismograph Standards; Seismograph Testing and Calibration; Vibration Limits, Technical; Vibration Regulations; and Program and Communications. Foremost, the Seismograph Standards section wrote the first two technical standards adopted by the ISEE. The historical accomplishments, current activities and objectives of the section are discussed.

Jan 1, 2003

By C. K. McKenzie

Presents outline of flyrock model and a field procedure to validate predictions of maximum projection distance. Field results are presented from 13 field tests with two different hole diameters.

Feb 1, 2020

By Rodney Pinksen, Remi Proulx

The IOC Mining and Operations Departments expressed an interest in reducing the amount of oversize material (>1.0 m x 1.0 m x 1.0 m; 39 inches x 39 inches x 39 inches) being produced and its subsequent downstream effects including in-pit sorting and reduction, damage to mobile equipment, and significant delays in the loading pockets and the primary crushers. To achieve this goal an oversize reduction project was undertaken by the mine and to date has significantly improved upon baseline measures.

Jan 1, 2011

By Demosthenes (Dennis) Efstratiadis

After European Council’s Directive 93/15/EEC of 5 April 1993 on the harmonization of the provisions relating to the placing on the market and supervision of explosives for civil uses, the so called ”Intra-Community Transfer of Civil Explosives” has been possible between users in the member States of the European Union. In line with this new approach, the placing on the market and the supervision of explosives for civilian use are subject to essential safety requirements. The explosives market in Italy is regulated by the ”day consumption of explosives” that imposes the user to have on site just the strict quantities of explosives and accessories that are necessary for the daily drill and blast activities. Any eventually advanced explosives’ quantities should be destroyed, either returned to the provider’s magazine until the 24:00 hours of the same day.

Jan 1, 2018

By Elliott Giles

"Measuring a blast’s performance based on the bucket fill time or “diggability” has always been achallenge due to the subjectivity generally involved. The diggability of a blast is often based onopinions and speculation without the data to properly support the claim. This paper focuses howthe blast design can impact diggability and how it can be properly measured."

Jan 1, 2016

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Charles Zdazinsky

"The Multiple Seed Waveform (MSW) blast vibration model, a type of waveform superpositionmodeling developed by Orica Inc., uses vibration data that is collected from a signature hole blast tocharacterize the ground’s seismic properties and determines the ground resonant frequency andfrequency range that is well supported by the ground. Additionally, the MSW model uses thisvibration data as input parameters to predict the resultant dominant frequency of a production blast. This information may in turn be used in conjunction with precise timing control to target theoptimum dominant frequency which promotes ground control."

Jan 1, 2016

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Allan King

Ammonium Nitrate (AN) is most commonly encountered as either a prilled solid or a highly concentrated aqueous solution, with or without organic ( e.g amine) nitrates. Under certain conditions of fire exposure involving prilled or solid AN, the molten state can be formed. The shock sensitivity of the molten material at temperatures greater than 220 Celsius has been found to be much higher than that of the prilled or solid form. Molten AN can be a precursor to events leading up to explosion of a bulk prill storage pile as a result of fire exposure. The explosion hazards presented by molten AN are a function of two factors; 1) its shock sensitivity and the deflagration to detonation ( DDT ) properties of the molten material, and: 2) the ability of large masses of unfueled prilled AN to be initiated and detonate. This paper presents the results of tests designed to determine the shock initiation and DDT properties of the solid ( prilled ) and molten AN.

Jan 1, 2008

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998