Search Documents

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By Lowell B. Moon

Regardless of how a mineral deposit in first discovered or by whom, any mining enterprise based upon it must pass through a preliminary stage of exploration. The common understanding of ?exploration? among mining engineers is well-expressed by Jackson and Knaebel:3/ Exploration work ranges from that performed by the individual prospector employing only the simplest tool, and equipment to elaborate campaigns involving the expenditure of largo stuns of money end the use of churn- car diamond-drilling equipment, large test-pitting crews, or sometimes a regular mining organization. In any event, the object is to determine as accurately as possible, with the funds available, the size, shape, and other characteristics of the ore bodies and their average value or grade.

Jan 1, 1945

By C. W. JEFFERS

At its annual meeting on March 5, 1928, in Washington, D. C., the Joseph A. Holmes Safety Association gave to the Ford Collieries Co., Curtisville, Pa., a certificate of honor for "having worked 922,628 underground man-shifts from August 14, 1920, to December 31, 1926, producing 5,755,669 short tons of coal without a fatality." This remarkable record certainly deserved recognition. It developed that this company's freedom from fatalities continued until October 2, 1929, hence the full period during which no underground fatalities occurred was from August 14, 1920, to October 2, 1929, or 9 years, 1 month, and 18 days, the total tonnage being over 7,700,000. Table 1, shows the complete safety record of the Ford Collieries Co. since 1920 as given by the officials of the company. The first item in Table 1 shows a remarkable performance. This company since 1920 has mined 15 times more coal per fatal accident than the average pro- duction per fatal accident for the State of Pennsylvania in 1928 (255,257 tons). Excluding the two fatalities (one in 1922 and one in 1929) the severity rate for the same period has been 1.259 per thousand hours worked, a record of which the company may justly be proud. However, including the fatal accidents the rate is 2.407. This compares favorably with an average of 12.4 in 1928 for 66 mines in the National Safety Competition. The Ford Collieries Co. operates three mines located in the vicinity of Curtisville, Allegheny County, Pa. One of these mines, Benjamin No. 1, is idle at the present time. The officials are: A. R. Pollock, general manager, Curtisville, Pa., and C. W. Pollock, assistant general manager in charge of safety and operation.

Sep 1, 1930

By H. F. Yancey

One of the important duties of the Bureau of Mines is to sample and analyze coals and to publish the results of such analyses for the information of producers, consumers, and the general public. Numerous publications containing such analyses have been Issued from time to time. Although the chemical properties of a coal as revealed by its proximate and/or ultimate analysis and heating value aid one considerably in visualizing its probable behavior and in determining its usefulness and value for a specific purpose, they do not furnish complete information. The physical properties of a coal, such as its ability to retain its original form without undue breakage or degradation in size under the various conditions of storage and usage, are also of importance in determining its suitability, technically or economically, for a given purpose.

Jan 1, 1932

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By H. A. Watson

This circular, which is a revision and combination of two previous publications,3 4/ presents information on the different types of equipment that may be used to analyze mine atmospheres, with particular reference to the application and limitations of each type. Such information is frequently requested by mining companies, State mining departments, and other agencies concerned with safety in mining who wish advice regarding methods of analysis of mine atmospheres and the equipment necessary for establishing laboratories for that purpose. Since the Haldane-type apparatus is particularly applicable to the accurate determination of carbon dioxide, oxygen, and combustible gases such as methane in mine atmospheres, that apparatus and the method of operation are described in detail. The circular presents results of a critical study of the accuracy attainable with the Haldane-type apparatus in the determination of methane in concentrations of the order of 0.25 percent, by volume. Analytical procedures involved in the other methods discussed are presented in publications referenced in this circular. Information is given also on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres, and suggestions on laboratory design are included. INTRODUCTION 'The analysis of mine atmospheres plays an important part in promoting safety and maintaining safe conditions in mining operations, particularly in coal mining, where the flammable gas methane presents a continuous hazard in Nome mines and may be encountered unexpectedly in others.5/ Methane has been encountered also, often unexpectedly and with disastrous results, in noncoal mines and in tunnels under

Jan 1, 1956

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By Hanns J. Billmayer

This report, which covers the period from April 1975 to November 1975, describes the work performed in compliance with the requirements of Contract No. H0357091. The purpose of this contract was the development of protective canopy concepts applicable to rail haulage equipment used in underground coal mines.

Jan 1, 1976

By Henry H. Ginsberg

The Federal Bureau of Mines made pilot plant investigations of the process requirements necessary to produce heavy fuel oil by the liquid-phase hydrogenation of bituminous coal. The investigation was carried out in three separate series of experiments. The first series studied the effect of temperature and contact time on product distribution at 3,500 p.s.i.g. and 420° to 480° C. in the presence of 0.1 wt.-pct../ stannous sulfide plus 0.05 wt.-pct. iodoform based on gross coal. As a result of increased contact times and temperatures, the conversion-6/ and yield of hydrocarbon gas increased, the viscosity of product oil decreased, and elimination of oxygen, nitrogen, and sulfur from coal increased. The yield of oil did not indicate any definite trend with changes in temperature and contact time. The yield of oil ranged from 76 to 85 pct. for Pittsburgh coal and from 60 to 85 pct. for Rock Springs coal. Asphaltenes in the product oil ranged from 17 to 38 pct. of the total oil for Pittsburgh coal and from 12 to 22 pct. for Rock Springs coal. Fuel oils meeting Bunker C or American Society for Testing Materials (ASTM) Grade 6 specifications were produced with Rock Springs coal at 0.2- to 1.0-hr. contact time and 440° to 480° C. and with Pittsburgh coal at 0.3- to 1.0-hr. contact time and 420° to 460° C. In the second series of experiments tin, nickel, iron, and zinc were evaluated as catalysts for the hydrogenation of Rock Springs coal to heavy fuel oil at 3,500 p.s.i.g. and 460° C. Using the apparent conversion of coal as criterion of catalyst activity, at a contact time of 0.45 hr. tin was the most effective catalyst; nickel and iron were nearly as effective, but the use of zinc resulted in much lower conversion. When the contact time was increased to 0.80 hr., the apparent conversion of coal was essentially the same for each of the catalysts. When the yield of oil boiling below 3550 C. was used as criterion of catalyst activity, at 0.45 hr. the order of activity was tin, iron, nickel, and zinc; at 0.80 hr. tin was far superior and the others were essentially equal. The product oils contained from 8 to 20 pct. asphaltenes.

Jan 1, 1960

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By Doris M. Hyde

The economy of Belize continued to show a very slight but still positive growth during 1986. The gross domestic product (GDP) was estimated to have been about $164 million,2 almost the same as those of 1984 and 1985. Foreign investors looked favorably on Belize because it had remained isolated from the sometimes turbulent political and social strife elsewhere in Central America. Reportedly, in late 1986, Guatemala had decided not to pursue its claim to Belizean territory and to give full recognition to that country. Discussions were to be held regarding any matters of mutual concern. New investment possibilities were oriented toward agriculture or manufacturing endeavors. Except for some interest in petroleum exploration, the minerals sector remained limited to the quarrying of construction-related materials.

Jan 1, 1988

In this U.S. Bureau of Mines report, two drill-split mechanical excavation mining system concepts are described, casted, and cost compared with conventional drill-blast mining systems. The concepts for the two drill-split mechanical excavation mining systems presented are (1) a method for steeply dipping narrow veins 0.6 to 1.2 m wide and (2) a longwall method for fiat-lying tabular ores. In the proposed systems, 70 to 80 pet of the ore is disposed of underground as backfill. For sortable ores, face area crushing, sorting, and direct stowage of run-of-mine waste and low-grade ores are proposed. The underground sorting and stowing of waste reduce materials handling, processing, and waste disposal costs by reducing the quality of ore transported to the surface by 70 to 80 pet (by volume). Because many of the tools and techniques proposed for use in these systems have little or no historical mining industry use, cost assignations are heavily influenced by engineering judgments and presented as prefeasibility-level cost estimates. These estimates, presented as discounted-cash-flow-rate-of-return (DCFROR) values, show the proposed systems to be at least as profitable as, and in some cases 50 pet more profitable than, conventional drill-blast mining.

Jan 1, 1994

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

1. Domestic Production and Use: In 1975.12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 67% of production capacity. Washington, Oregon, and Montana accounted for 37% of the total production; Gulf Coast States 21%, Northern States 29%, and other Southern States 13%. Output of primary metal in 1975 was valued at $3.0 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1975, building accounted for about 21%; transportation 19%; electrical 14%; packaging 18%; and consumer durables, 9%.

Jan 1, 1976