Search Documents

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By William A. Sloan

"In smelting operations, finely divided material called ""flue dust"" is carried by the moving gases from the roasters and furnaces; it is partly settled and recovered in the flue system. The flue dust from copper smelters contains a high percentage of copper, usually some gold and silver, and occasionally other valuable metals. It is too valuable to throw away and in present practice is returned to the smelting furnaces for re-treatment. A part of this material again passes out with the gases and forms a circulating dust load in the system. The dust that passesout of the stacks into the atmosphere is an important source of loss in copper smelting. Loss of values also occurs by dust being blown away while in transit from the flues back to the furnace, and of course the greater the amount of rehandling the greater this loss.Dust carried in the gas currents causes corrosion of the roof arches in reverberatory furnaces. Returning flue dust to the furnace increases the quantity of suspended dust. Corrosion reduces the life of the arches and shortens the length of furnace campaigns; also the corrosion of arches limits the temperature at which a furnace may be operated. Every ton of material that must be re-treated in the furnaces reduces correspondingly the amount of new ore or concentrates that could be smelted.As the present tendency is toward finer grinding in flotation plants smaller particles will need to be treated at the smelters, increasing the difficulty of preventing losses in flue dusts. Many schemes and processes for a more economical method of treating flue dust have been proposed or tried, but in the main none of them has been successful."

May 1, 1928

This status report contains 39 individual reports on health and safety research projects now being conducted or recently completed by the Bureau of Mines. The Reports on health research cover industrial hygiene, respirable dust, ventilation, noise control, and radiation hazards. The safety research reports cover industrial hazards, ground control, fire and explosion prevention, and methane control. Each report includes background information, a discussion of research progress, and an assessment of each project's current status.

Jan 1, 1979

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By A. E. Ketler

A second generation lighting system was installed in the Greenwich Collieries longwall. This report describes the hardware, installation, maintenance, and final results of the program.

Jan 1, 1978

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941

By Forrest T. Moyer, J. I. DAVIS, JOSEPH H. SCHUSTER, E. K. ELSNER

The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior, is held each year for the purpose of promoting safety in the mineral industries of the United States. Since the program was inaugurated in 1925, twenty-three safety competitions have been held. This publication is a report of the results of the contests held in 1944, 1945, 1946, and 1947. The names of plants that have been awarded "Sentinels of Safety" trophies and Certificates of Achievement in Safety dur- ing these years, together with a summary of their achievements in injury prevention, are listed. Statistical data covering the injury experience of all plants entered in the annual contests also are included in this publi- cation. The injury statistics of these plants, arranged in the six groups of the competition, are the only data on injury severity at mineral operations available to the Bureau of Mines. Interest in the National Safety Competition has increased steadily. The number of participating plants has increased from 210 in 1925, the first year of the competition, to the record number of 494 in 1946. The widening scope of the competition means that a steadily increasing number of the mines and quarries in the United States are participating in a program that will supplement their other activities in promoting safety. Safety competitions have long been recognized as instrumental in stimulating and holding the interest of employees and officials in accident-prevention work. During the years covered by this report, conditions in the mineral industries of the United States were hardly conducive to setting records in accident prevention. During the war years, handicaps were especially severe- loss of skilled employees to the armed forces or to higher-wage war industries, greater production by a smaller force of workers, relatively high rates of labor turn-over, the longer workday in effect through 1944 and 1945, and difficulties in obtaining repairs and replacement for badly worn machinery. Even the immediate postwar period has brought no abatement of the tremendous pressure upon the mineral industries for greater production. Although there was a decrease of 18 in 1947 from the record enrollment in 1946, these oper- ations worked 160,525,025 man-hours, the greatest number of man-hours of exposure to mining hazards in any year of the contest except 1942. Despite the accelerated pace at which the mineral industry worked during the 4 years covered by this report, participants in the National Safety Competition have achieved creditable performances in the promotion of safety. In fact, the injury-severity rate in the enrolled plants in the 1947 contest was 7.315 days for each thousand man-hours worked, the lowest by far in the history of the National Safety Competition. The injury-frequency rate of 42.155 for each million man-hours of exposure to mine hazards in 1947 marks a favorable trend downward from the rate of 50.577 in 1946, which was the

Dec 1, 1949

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By Mark Sheppard

[Considerable research work hi been done on secondary crushing and coarse and fine grinding, and the literature on the general subject of Crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigator is concerned largely with the production of fine material and the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention.]

Jan 1, 1938

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a part of the 21,296-acre Million Hills Wilderness Study Area (NV-050-233) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 46 miles south of Mesquite, NV. The area is on the east edge of the Gold Butte mining district and has had minor production of copper and zinc from the Azure Ridge mine in the early 1900's. Assessment work was being done on the Esperanta claims, which covers the mine workings, in March 1987.

Jan 1, 1988

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.