Search Documents

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By James D. Cooper

COMBINED tonnage or natural abrasive materials sold or used in the United States in 1962 was 10 percent greater than that of 1961 and value was 9 percent higher. Production of crude artificial abrasives in the United States and Canada was up 14 percent in volume and 9 percent in value. Value of grinding-wheel sales increased 13 percent, and the value of coated-abrasives sales was up 10 percent. The value of imports and reexports declined, while the value or exports increased. [ ]

Jan 1, 1963

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By Avery H. Reed

RECORD production of marble, kaolin, scrap mica, and talc high-lighted the mineral industry of Alabama in 1962. Among the States, Alabama ranked second in scrap mica, third in the production of bauxite and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by mining and processing of coal and iron ore, and the manufacture of cement, which together comprised 73 percent of the total value of production, compared with 72 percent in 1961. Other important industries were the production of crude petroleum, and stone quarrying. Leading companies were Tennessee Coal & Iron, Southern Cement Co., Southeastern Electric Generating Co., Alabama By-Products Corp., and U.S. Pipe & Foundry Co.

Jan 1, 1963

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

By F. E. Griffith, C. H. SEELING

Cardox blasting is used widely in coal mines in the United States . A model of a Cardox blasting device was approved by the Bureau of Mines subject to certain conditions and limitations , and the approval was extended to other models from time to time . Certain special hazards are entailed in the use of Cardox as with explosives . One of these is flying shells . In some blasts , the Cardox shell is violently ejected from the borehole and flies like a projectile , frequently ricocheting off solid objects and striking points considerably off the line of its initial flight . Flying shells have been known to pierce the webs of structural - steel beams , to pass through both sides of allsteel mine cars , to be driven through stout hardwood timbers , to knock out timber sets , to damage loading equipment , and to break or short - circuit power lines . A considerable number of shot - firers and other workers have been struck by flying shells and killed or injured . Accidents from this cause , although not as frequent as other types of mine accidents , are usually serious , closely approximating accidents caused by blasting with ordinary explosives . The increasing number of such accidents prompted a Bureau of Mines field investigation of possible methods of preventing dangerously violent ejections of Cardox devices . This report contains pertinent data collected during the investigation and describes methods tested and discarded as well as the development and proof of an apparently satisfactory method .

Jun 1, 1943

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By Henry R. Ensminger

Brazil's gross domestic product (GDP) grew only slightly in 1988 to $277 billion at current prices.2 The growth rate was the smallest registered since 1983, when the rate was minus 2.8%. The economy's performance was strongly influenced by a 2% to 3% decrease in industrial production and civil construction. The mineral industry, however, countered the downward trend in the industrial sector and grew a modest 1.4%. In November, Brazil adopted a new Constitution that placed significant restrictions on foreign investment in the mineral industries. Under certain provisions of the new Constitution, foreign companies were prohibited from establishing new mining ventures in Brazil as sole or majority owners. They could now enter the mineral industry only as minority shareholders with Brazilian partners. Foreign companies already established in Brazil had a 4-year grace period to find majority Brazilian partners, or to establish vertically integrated processing operations (mining, processing, smelting, and refining). The new Constitution also prohibited foreign risk contracts for petroleum exploration.

Jan 1, 1990

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By Edward L. McHugh

The Thousand Lakes Wilderness has no known economically significant mineral resources. However, the geologic setting of the Wilderness indicates a potential for the discovery of geothermal resources. INTRODUCTION The Thousand Lakes Wilderness occupies 16,335 acres (6,611 ha) in eastern Shasta County, California. A mineral resource study of the area was authorized by the Wilderness Act of 1964 (Public Law 88-577). Mining records and published information were examined, and field investigations conducted in 1979. The Wilderness is about 50 miles (80 km) east of Redding and 12 miles (19 km) south of Burney, California. It lies in the Cascade Range of California. Relief is more than 3,000 feet (910 m); elevation is greatest at the summit of Crater Peak, 8,677 feet (2,645 m).

Jan 1, 1982

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

By David Hill

The Australian underground coal mining industry has made extensive use of the Coal Mine Roof Rating (CMRR) classification system for a diverse range of purposes in recent years. These include mining method selection, and coal pillar and roof support design. This paper outlines a series of case histories, from large-scale feasibility studies to local support design investigations, that collectively illustrate the broad applicability, advantages, and usefulness of the methodology, as well as some of the current limitations. The key role of the CMRR in an overall hazard definition methodology is demonstrated for a major Australian project, and some ideas with regard to the future application of the CMRR, in the context of geotechnical risk management within a progressive, highly productive extractive industry, are put forward.

Jan 5, 2007

By Henry P. Chandler

TONNAGE of natural abrasives sold or used in the United States in 1959 increased 12 percent. Artificial abrasives produced in the United States and Canada jumped 24 percent. Imports, exports, and reexports of abrasive materials also showed gains. Sales of grinding wheels were up 33 percent and coated abrasives 17 percent. FOREIGN TRADE Imports of abrasive materials totaled $91 million, an increase of nearly 51 percent over 1958. Chief commodities contributing to [ ]

Jan 1, 1960

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947