Search Documents

By Ted C. Briggs

A special high-pressure Burnett-type compressibility apparatus was constructed and used to determine compressibility factors for pure helium, pure nitrogen, and nine helium-nitrogen mixtures containing 89.47, 79.04, 69.69, 60.09, 49.24, 41.02, 30.99, 20.53, and 10.67 mole-percent helium. A total of 161 runs were made consisting of 2,355 observed pressures. Data were obtained at 0°, 25°, and 50° C and at pressures to 1,000 atmospheres. A power series in the reciprocal volume, commonly called a Leiden series, is used to represent the compressibility factors. Three parameters in the series are required to represent helium, five parameters to represent nitrogen, and from three to five parameters to represent the mixtures. Compressibility factors are believed to be accurate to better than 0.1 percent over the entire pressure, temperature, and composition range.

Jan 1, 1972

By D. S. Kingery

This study describes five fatal accidents so unusual in occurrence that the chain of circumstances bringing them about may never be duplicated. The intent of this publication is to illustrate that everyone working underground is subjected, at all times, to definite inherent mining hazards and that safety devices, though provided, often are ineffective or not used. It is hoped that a study of these fatal accidents in bituminous-coal mines will show workers and safety engineers that nothing can be taken for granted. Safety planning with continuous study can prevent these unusual accidents as well as the routine recurring types, which cause the majority of coal-mining injuries. The treacherous, fatalistic philosophy that "it can't happen to me" or that "when my time's up I'll get it regardless of what I do," still prevails among individuals and even safety engineers. The individual or safety man who believes in luck as applied to safety should not read any further, since this study was written for the sincere, safety-minded individual who accepts the prevention of all accidents as a challenge to his knowledge, initiative, persuasiveness, and salesmanship.

Jan 1, 1954

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By Lloyd A. Morley

Two mine electrical power system simulations are presented. The first is a batch processed procedure capable of modeling a single mining machine consisting of a number of motors operating under various loads. These loads are the mechanical torque loads present at the motor shaft. The second simulation is a more flexible tool for modeling entire mine electrical power systems~ Detailed analyses of bus voltages, transmission-line power flows, and machine behavior are possible. This simulation operates interactively and the power system is configured as the user responds to program generated questions and requests. Development of the theory behind the programming, as well as detailed explanations of the models, is presented. Examples are provided to demonstrate simulation capabilities.

Jan 1, 1978

By Samuel S. M. Chan

The objective of this project was to collect information applicable to the design of ground support systems in deep mines to include in-situ rock deformations, deformation-modulus, stresses, and geology and laboratory physical properties. All data collected was to be integrated and evaluated using a finite-elements computer code. In addition, considerable professional "cross pollenization" was anticipated from the association of University and SMRC personnel. Scope of Investigation Before a ground supporting system can be evaluated, the loading conditions existing in the region of investigation, strength, deformation characteristics, as well as other engineering properties of the rock structure immediately surrounding the openings, together with the pertinent geological information, must be obtained and analyzed. It was for this reason the following items were included in this research project: (1) The selection of a suitable area for the investigation. (2) The mapping of the important geological features of the area of investigation. (3) The measurement of in-situ deformation of rock masses immediately surrounding an underground opening of the area of investigation. (4) The determination of ground stresses. (5) The obtaining of in-situ modulus of deformation of the rock masses. (6) The testing of useful engineering properties of

Jan 1, 1972

By N. Kumar Kittusamy

Operators of construction equipment perform various duties at work that expose them to a variety of risk factors that may lead to health problems. A few of the health hazards among operators of construction equipment are: (a) whole-body vibration, (b) awkward postural requirements (including static sitting), (c) dust, (d) noise, (e) temperature extremes, and (f) shift work. It has been suggested that operating engineers (OEs) are exposed to two important risk factors for the development of musculoskeletal disorders: whole-body vibration and non-neutral body postures. Method: This review evaluates selected papers that have studied exposure to whole-body vibration and awkward posture among operators of mobile equipment. There have been only few studies that have specifically examined exposure of these risk factors among operators of construction equipment. Thus other studies from related industry and equipment were reviewed as applicable. Conclusion: In order to better understand whole-body vibration and postural stress among OEs, it is recommended that future studies are needed in evaluating these risk factors among OEs.

Jan 1, 2004

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and standard enthalpy of formation were made by the Federal Bureau of Mines for basic aluminum sulfite, A1203?2.0S02?5.3H20. The standard values of entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 85.2±0.1 cal/deg-mole, -943.1±1.2 kcal/mole, and -820.7±1.2 kcal/mole, respectively.

Jan 1, 1976

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

By Dennis R. Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson’s effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

By John C. Edwards

Carbon monoxide (CO) sensors are used in mine fire early-warning systems. Experiments were conducted by the U.S. Bureau of Mines with six diffusion-type CO sensors to determine their response to a reference CO concentration under both static and dynamic flow conditions. Static experiments were conducted with 0.5 L/min flow of 16 ppm CO in N2 through 8-and 12-L chambers. Dynamic flow experiments were conducted in two environmental chambers: One had directional flow capability of 1 m/s, and the second provided moderately nondirectional flow as high as 1.8 m/s. Reference CO concentrations of 13.5 to 19 ppm in air were used for the dynamic experiments. The results of the static experiments demonstrated that the sensors consistently underestimated the reference gas concentration. The dynamic experiment results showed the sensors provided reasonable agreement with the reference gas concentration when directional flow effects were not considered. Directional flow effects were evaluated for two sensors. One of the sensors showed a strong dependence upon the relative orientation of the diffusion tube with respect to flow direction. The second sensor did not show a dependence upon flow direction. The sensors' directional flow effect is significant for their proper in-mine utilization.

Jan 1, 2010

By Sumner M. Anderson

ATHOUGH scattered signs of increased activity in the mining industry accompanied an incipient improvement in the overall economic situation during the latter months of 1963, production levels for the year as a whole responded to the general 1962-63 business recession with a 4.2 percent decline. The petroleum industry, active since 1907, did not become a dynamic force in the economy until exploration and drilling contracts were concluded with private companies in 1958 and 1959; on November 15, 1963, having virtually achieved self-sufficiency in petroleum in the preceding year, those contracts were unilaterally annulled. In the field of metallics, the only approach to internal sufficiency-aside from the iron and steel industry that has depended heavily on the importing of basic raw materials-has been in mining, smelting, and refining lead and zinc although iron ore, silver, beryllium, tantalite, and tungsten have been mine production items of economic significance. Reserves of lead, zinc, silver, bismuth, vanadium, and low-grade and metallurgically difficult iron ore-as well as those of beryllium, tantalite, and tungsten which are produced primarily for export-appear to be fairly abundant. The exploration of deposits of copper, cobalt, tin, lithium, gold, manganese and uranium has been undertaken on a relatively small scale, and little precise information is available on the extent of reserves. Argentina is dependent on foreign sources for part of its required iron and steel and, except for lead and zinc, most of its nonferrous metals. Nonmetallies and solid fuels present an exceptionally varied array of production items among which cement had the second largest 1963 output in South America. Borates, bentonite, common clay, diatomite, fluorite, granite, lime, limestone, obsidian, onyx, rhodochrosite, salt, and spodumene ordinarily are produced for export either exclusively or in excess of domestic consumption requirements. Barite, cement, chalk, gypsum, marble, and mica are both exported and imported. Argentina depends entirely or partly on imports for coal and coke, certain special types of clay, mineral abrasives, graphite, magnesite, mineral fertilizers, sulfur, talc, and minerals for construction, the last group being chiefly attributable to convenience of river transport from Uruguay.

Jan 1, 1964

By D. A. Reynolds

THIS REPORT gives results of an investigation of the carbonizing properties of two Tennessee coals, one from the Jellico bed in Campbell County and the other from the Sewanee bed in Marion County. Jellico coal and blends with 20 and 30 percent Pocahontas No. 3 coal were carbonized at 800° and 900° C. by the BM-AGA method. Sewanee coal was carbonized by the same method at 800°, 900°, and 1,000° C.; blends with coals of similar and different ranks were carbonized at 800° and 900° C. The coals were subjected to various physical and chemical tests, including complete chemical analyses, low-temperature assays, and agglutinating, free-swelling, friability, plasticity, and expansion tests. The Tennessee coal field is a part of the Appalachian field, which extends from northern Pennsylvania to central Alabama. The Jelico bed, one of the most important in the State, is part of the Jellico formation, which is above the Lee formation of the Lower Pottsville. Sewanee coal bed belongs to the Sewanee conglomerate and is stratigraphically lower than the Jellico bed.

Jan 1, 1953