Search Documents

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By Ellis S. Hertzog

The data published in this report cover only one phase of a special study of the physical and chemical properties of Alabama coals made by the Bureau of Mines. In addition to determinations of friability, the survey included determinations of grindability, B.t.u. value, end ash-fusion temperature. Assay distillation tests, both for high- and low-temperature carbonization, and proximate and ultimate analyses were made also. However, this preliminary paper is concerned only with the results of friability tests and is issued to expedite the release of this information to the public. The friability test measures the liability of a coal to break into smaller pieces when subjected to repeated handling, as occurs in the mining, preparation, and transportation operations. Friability depends on many physical characteristics of the coal that vary not only between different seams but also in the same seam. The laboratory methods of determining friability have been developed to give a practical means of estimating degradation of size. So far as is known to the authors, no data on the friability of Alabama coals have ever been published. This paper makes available for the first tine fairly comprehensive information on this subject. Because the procedure for the tumbler test for determining the friability of coal is relatively new to the coal operators, the authors have included a complete description of it in this report.

Jan 1, 1938

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

Aluminum Production. -By October 1, Aluminum Company of America will restart a 35,000-ton-per-year unit at its aluminum smelter at Rockdale, Tex., restoring that facility to its full capacity of 325,000 tons annually. Primary Ingot Price Increase. -Most U.S. aluminum producers in mid-September were quoting a price of 72 cents per pound for primary aluminum ingot. On September 19, Kaiser Aluminum & Chemical Corp. announced that it would increase the price of primary aluminum ingot 4 cents to 76 cents per pound.

Jan 1, 1980

By M. M. Myers

"Importance pf the small stone problem.Profitable disposal of limestone too small for making lime in the shaft kiln, is one of the most urgent problems in the lime industry. Reports received by the Bureau of Mines from 31 quarries show that the proportion of small stone varies from 2 to 40 per cent, averaging 18 per cent of gross pro¬duction, Modern methods of heavy blasting, and the use of crushers in large quarries tend to increase the proportion of small stone above that produced in early days when light blasting and hand sledging were almost universally used. There is also a growing movement toward underground operation of lime deposits, a method which in general produces a greater proportion of fines than is encountered in open-pit work. Thus the small stone problem is of growing importance, and demands the attention of every progressive lime producer. As the problem is of almost universal interest, it is urgently desired that every operator who reads this report will contribute from his knowledge or experience, answers to the questions on the final sheet.There are several markets in which small stone may be sold but in these markets the competition is generally keen and the prices low. The lime producer's chief product is lime, he understands its manufacture and marketing, and brings him a greater return than can be obtained from most limestone by-products. For these reasons it is evident that the conversion of small into lime is the nest desirable means of disposal."

Apr 1, 1924

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987

By V. B. Dale

This paper is one of a Federal Bureau of Mines series covering the mineral resources of the Nation. It briefly describes most of the tungsten deposits in Cochise, Pima, and Santa Cruz Counties, Ariz. Most of the descriptions are from field examinations by the two senior writers, prior to July 1957. Wolframite first was identified in Arizona in 1896 by W. P. Blake, Territorial Geologist. Tungsten mining began about 1900 in the Little Dragoon deposits of Cochise County, and about 1901 in Las Guijas district of Pima County. The price history of tungsten is an erratic one; consequently, production has been erratic. Prices rise during wars and periods of national preparedness. Production of tungsten ore was stimulated greatly by a Government purchasing program, announced on May 10, 1951, wherein the Government agreed to purchase standard-grade tungsten concentrates at $63 per short ton unit5/ for 5 years or until 1,468,750 units were purchased. This was later increased to 3,000,000 units, and after this amount had been purchased in June 1956, the purchase of an additional 1,500,000 units was authorized. Government purchase, however, was suspended in December 1956 before completion of this latter program, and the price of tungsten concentrates declined sharply. The price had dropped to $15 per short ton unit, duty extra,6/ by the last part of July 1957.

Jan 1, 1960

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

By J. C. Nigro

Hematite-to-magnetite reduction kinetics were investigated mainly in CO-CO2 atmospheres at temperatures ranging from 500° to 1,000° C. Reduction rates were measured with a thermobalance, which recorded the weight loss as the specimen was reduced. Reduction data on both synthetic and natural hematite spheres showed good linearity of ro [1-(1-R)1/3] with time, t, up to over 85 pct conversion to magnetite; the rate coefficient (k[L], cm/min) obtained from the linear portion of the plot was used to characterize the penetration rate of the hematite-magnetite interface. Gas composition, porosity, and silica content were major factors affecting the rate. Temperature dependency of the reaction rate was small, yielding a mean activation energy of about 3 kcal/mole. Silica additions increased the reaction rate, probably through an increase in the effective surface area and diffusion; however, above 900° C, silica can react to form fayalite. Experimental data showed that the linear thickening rate of the magnetite layer, normally evidence of a chemically controlled reaction, can also be indicative of a reaction controlled by both mass transfer and diffusion. Evidence from this study indicates that the dominant rate-controlling factor in the reduction of hematite to magnetite at high temperatures is transport in the gas phase.

Jan 1, 1973

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can't happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By Charles Prasky

This report describes bench-scale studies and pilot-plant development of the Bureau of Mines process for roasting iron ores with a ferrous scrap reductant, such as discarded automobile hulks, to yield artificial magnetite. Quality magnetic concentrates containing about 66 percent iron and 6 percent silica with iron recoveries of over 90 percent were obtained after roasting fine-grained oxidized or nonmagnetic taconite with unburned, sheared automobile hulks in a rotary kiln. The relatively complete oxidation of the lighter gage metal in the automobile during roasting resulted in a metallic byproduct consisting of the unconsumed heavier gage metal scrap. This residual or tailored scrap is potentially useful as heavy melting stock and has more value than the original automobile hulk.

Jan 1, 1970

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the fifteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by halt townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The Descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By J. L. Wiley

[NOTE. - P before the number indicates that the ab tract appears in patent section. Abstract numbers without. P appear in literature section. A Abietic acid, hydrogenolysis - 404 Acetone, recovery - P-4024 Acetylacetonate catalyst - P-3352, P-3664, P-6067 Acetylene, production - P-2556, P-3169, P-4064, P-4221, P-4222, P-5002 Acid catalyst - P-4584 Salts - P-4555 See also Specific acid. Acid treatment. See Procedure. Adsorption. See Hydrogen, adsorption. Agitation. See Equipment, agitators; Procedure. Alcohols: Decomposition -1128 Hydrogenation - P-3288, P-4743 In motor fuel - 1486]

Jan 1, 1952