Search Documents

By J. A. Organiscak

The U.S. Bureau of Mines recently conducted an investigation into the amount of respirable and quartz dust generated while mining rock in coal mines by continuous and conventional methods. The study was made at two mines that use both continuous and conventional mining. Results show that continuous mining produces 1.2 to 3 times more respirable dust, and 6.7 to nearly 15 times more quartz dust than conventional mining.

Jan 1, 1989

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

By James E. Bell, Clyde B. White

"INTRODUCTION The Friedensville district was one of the most important zinc-producing areas in the United States from 1859 to 1893. The ore minerals near the surface were principally calamine and smithsonite, but with depth sphalerite was found in increasing proportions. The ore bodies of the district are reported to have been in chimneys, occurring in folded and faulted beds of Beekmantown limestone of Ordovician age.The Correll was one of five mines near Friedensyille that were exten¬sively exploited. The high-grade ore shoots were mined to a depth of several hundred feet, but it is believed that inability to compete with lower-cost production elsewhere, rather than exhaustion of the ore bodies, compelled the mines to close.There is no record to indicate that any attempt was made during the period of operation to explore for additional ore in the limestone beds down the dip below the mine workings. The possibility that exploration might reveal additional ore in the limestone beds below the known ore shoots led the Bureau of Mines to diamond-drill the Correll property between September 1943 and January 1944."

Jan 1, 1948

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By Wilder H. Brinton

"INTRODUCTION The Queen Mary copper property is in sec. 18, T. 12 N., R. 16 W., in the Clinton mining district of Missoula County, Mont. It was examined by an engineer 3/ of the Bureau of Mines, November 21, 1943. Upon the basis of his recommendations, a small trenching and diamond-drilling program was begun November 11, 1944. One diamond-drill hole was completed December 16, -944, but because of frozen ground trenching was postponed until June 1945 and then completed. This report describes the results of exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests. Both of these branthes are under the supervision of Dr. R. S. Dean, assistant director.The chemical analyses included in this report were made at Reno, Nev., under the direction of A.C. Rice, acting engineer in charge. Rare and Precious Metals Experiment Station, Bureau of Mines."

Nov 1, 1946

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

The National Personal Protective Technology Laboratory (NPPTL) of the National Institute for Occupational Safety and Health (NIOSH) has undertaken a collaborative study with the Mine Safety and Health Administration (MSHA) to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), withstand the underground coal mining environment with regard to both physical damage and aging. Apparatus tested included the CSE SR-100, the Draeger OXY-K Plus, the MSA Life-Saver 60, and the Ocenco EBA 6.5 and M-20. This report presents findings regarding laboratory-tested SCSRs in the tenth phase of testing, from July 2004 to March 2006. The SCSRs were tested on a breathing and metabolic simulator and on a human subject walking on a treadmill. The tests performed in this study are not the tests used for certification (Title 42 of the Code of Federal Regulations, Part 84). The tests performed in this study continue until the apparatus are empty to enable comparison of new versus deployed apparatus. The method for obtaining deployed SCSRs for this evaluation was not a random selection from the deployed population of SCSRs. We sought older apparatus with visible environmental impact rather than newer apparatus, and we attempted to sample a wide range of deployment modes. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. This report is the last of 10 report phases begun in 1982. Previous reports describe phases 1 through 9 [Kyriazi et al. 1986; Kyriazi and Shubilla 1992, 1994, 1996, 2000, 2002, 2004, 2006] A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the applicability of the results. The results of these studies suggest that the large majority of SCSRs that pass their inspection criteria can be relied upon to provide a safe level of life support for mine escape purposes. However, the storage and handling in the mining environment seems to have caused performance degradation in some of the apparatus. In this phase, phase 10, we found some CSE SR-100s (93 tested) that exhibited high CO2 levels, stuck-together breathing hoses, starter-O2 failure, breathing hose punctures and tears, high breathing pressures, and loose particulates in the breathing hose. The loose particulates caused coughing in human-subject tests. One MSA Life-Saver 60 (20 tested) in this phase had a stuck-open relief valve. One Ocenco EBA 6.5 (50 tested) had an unattached O2 supply hose. An unexplained phenomenon occurred with two Ocenco M-20s (20 tested): low O2 flow rates preventing their successful use. Almost all of the failures noted involved units that failed their inspection criteria.

Jan 6, 2008

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By G. E. McElroy

[The ventilation of development faces In nines for diluting Gas or dist concentrations and, in hot nines for providing air-motion cooling effect, by fan-pipe units discharging high-velocity steams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, n subject on which little definite information is available. A study of the air flow from grills into rooms3/ has provided some basic data, but under conditions so different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.]

Jan 1, 1940

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By D. Harrington

While apparently the hysteria with regard to silicosis and other occupational diseases has largely subsided and this subject is being more carefully considered and soberly judged, it would be poor policy for any employer to maintain that the storm has ended and that he can relax and revert to conditions as they were 5, 10, or more years ago. The fact is that the plan of paying occupational-disease compensation is now in its infancy and can be expected to grow rapidly. At present, while all of the States of the Union, including the District of Columbia and excepting only Arkansas and Mississippi, have compensation acts, only the following make provision for occupational diseases to some extent or in one way or another: California, Delaware, Connecticut, District of Columbia? Illinois, Indiana, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rhode Island, Washington, West Virginia, and Wisconsin. Silicosis is compensable in one way or another in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin, and possibly in other States. During the past few months, occupational-disease legislation (largely silicosis) has been considered in some form in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah and Washington. It will be surprising if comparatively comprehensive occupational-disease legislation is not on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the farsighted industrialist who has the interest of his organization at heart, if he has not already done so will immediately start to "put his house in order" by studying possible occupational disease hazards to his employees and promptly applying known remedial measures or attempting to devise such measures if none exist. Unquestionably, one of the most important of the surveys to be made relates to dust occurrence, as State laws on occupational disease are almost certain to contain provisions, on silicosis and, with almost equal certainty, the provisions of any State law are not likely to be particularly similar to those of other States.

Jan 1, 1938

By M. R. Geer

All the coal lands in Alaska are publicly owned, and the Federal Government is the principal consumer of coal. Therefore the Government has long been concerned with the wise utilization of the coal reserves of Alaska as well as with the availability of coals meeting the specifications for use in various Government installations. Coal preparation plays a key role in both of these areas of interest. The proper choice and operation of coal-washing equipment permits the mining of inferior deposits, minimizes waste of coal in preparation, and assures a prepared product of the best quality obtainable from the raw coal. Thus, from time to time, the Bureau of Mines has made washability examinations on most of the coals mined in Alaska. Generally, these examinations were made when new mines or new beds were opened, when construction of new preparation plants was being considered, or when the operation of existing plants could be improved by better knowledge of the raw coal. The purpose of this report is to bring together all the washability data available on the coals of the Matanuska Valley and Beluga River fields. The pattern of energy development for the rapidly growing Anchorage area is not clear at this time. Formerly coal was the only fuel available for large-scale space heating and power generation. More recently both oil and natural gas have entered the market, and several hydroelectric projects have been completed. Additional major hydroelectric projects are being considered. The role that will be played by coal in this competitive energy market is uncertain. However I if coal is the fuel used in future power plants or industrial installations, the information contained in this report will be useful in indicating the quality of the coals that can be supplied and in selecting proper preparation techniques.

Jan 1, 1962

By R. K. Koch

The normal spectral emissivities of liquid Ti, V, Zr, Mo, and Pt were determined at the fusion temperatures in an electron-beam furnace using a water-cooled copper hearth. The normal spectral emissivities were estimated above the melting points by using adjusted two-color temperatures as approximations of the true temperatures for substitution in Wien's equation. Simultaneous brightness temperatures were determined with a micro-optical pyrometer. The true temperature ranges covered were 1,668° to 1,885° C for Ti; 1,919° to 2,013° C for V; 1,855° to 2,367° C for Zr; 2,610° to 2,751° C for Mo, and 1,772° to 1,990° C for Pt. The spectral emissivities for titanium and zirconium decreased with increasing temperature. At an effective wavelength (?) of 658 mµ the emissivity of titanium ranged from 0.51 to 0.45 and zirconium, from 0.47 to 0.41. The emissivities of vanadium (? = 658 mµ) and molybdenum (? = 657 mµ) were constant at 0.41±0.02 and 0.33±0.01, respectively. The spectral emissivity of platinum (? = 658 mµ) was constant at 0.39±0.02 up to 1,900° C; above that temperature anomalous data were obtained. A mass spectrometric study indicated that platinum was reacting with back-streaming silicon vapors from the diffusion pump when the ambient pressure was greater than 2 X 10-5 torr.

Jan 1, 1973

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

By G. A. Smyres

The Bureau of Mines conducted laboratory studies to determine the feasibility of chlorine-oxygen leaching for treating low-grade zinc sul-fide flotation concentrates. Recovery of zinc sulfides by flotation from complex fine-grained sulfide ores is substantially higher in low-grade bulk sulfide concentrates than in the high-grade cleaned concen-trates required for smelter feed. However, there is no commercial process in the United States for the treatment of low-grade bulk zinc sul-fide concentrates. Leaching experiments using reactors of 500-mL and I-gal capacity were conducted on a bulk concentrate containing 19.3 pct Zn, 35.6 pct Fe, and 39.4 pct S. The effects of pressure, temperature, and percent solids on extraction were investigated. The chlorine-oxygen leaching procedure showed promise for treating the concentrates. Zinc extractions of 95 pct or more were obtained by leaching at 50 pct solids in the temperature range of 1000 to 1200 C. Zinc extractions by leaching with chlorine followed by oxygen at reactor pressures of 50 to 100 psig were independent of pressure.

Jan 1, 1985

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

By A. C. Johnson, McHenry Mosier

The Bureau of Mines has adapted its activities to needs of national defense and to conditions brought about by the war program . Its work is now oriented solely to war problems . After studying about 1,600 deposits of war minerals , exploration projects have been undertaken on 96 of the most promising , of which 56 have proved successful . These have indicated that 56 million tons of ore of commercial or near -commercial grade can be utilized to meet war requirements . Included in this amount are 1 million tons of tungsten ore ; 4 million tons of chromite ore, 10 million tons of manganese ore , 2 million tons of antimony ore , 1 million tons of mercury cre , and 28 million tons of iron ore . Work done in connection with exploration projects included 172,000 feet of surface trenching , 210,000 feet of drilling , and 21,000 feet of shaft sinking . Nearly 100,000 samples were taken, on which 500,000 analyses were made . Extensive metallurgical tests were made on ore from many of these deposits , both in the laboratory and in pilot plants , in connection with research to develop metallurgical processes for their treatment .

Jan 1, 1943

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929