Search Documents

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By W. D. Dietzman

This Bureau of Mines report presents a continuation of statistics pertaining to distribution of petroleum reservoirs (or fields), wells, and production by depth and producing rate classification in the United States. These statistics show the change that has occurred since results of a similar study were published by the Bureau of Mines in 1967. Data are presented in tabular form by State for the 18 principal oil-producing States and by subdivision for the two largest oil-producing States, Texas and Louisiana. Tabular summations and graphical illustrations are presented for the Nation. The data are classified by 4-barrel-of-oil-per-day rate increments up to 36 barrels and one increment of greater than 36 barrels of oil per day and by 2,000-foot depth increments up to 8,000 feet and one depth increment of greater than 8,000 feet. The overall average producing rates for States and the Nation have been published for many years, and although such rates are useful, they are very general descriptions of producibility. A breakdown of production, wells, and reservoirs by various depths and rates and by State or by State subdivision provides a more detailed description of producibility.

Jan 1, 1975

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young's modulus, shear modulus, and Poisson's ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young's modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By David C. Chang

A survey of in-situ methods for determining bulk electric properties of coal is given. Largely because of the strong dependence of coals properties on operating frequency, different sensing methods have to be adopted for different applications. Evaluation of both established and feasible methods is made in this report from the viewpoint of physical set-up, probing depth, and the type of inversion involved.

Jan 1, 1977

By Manuel Gomez

The Bureau of Mines used data from 31 core samples to develop prediction equations for evaluating chemical and carbonization properties of six seam units in a lignite deposit approximately 2 miles wide and 8 miles long in the Wilcox Formation of central Texas. Statistical response surfaces, based on core analyses, were computed for 14 parameters indicative of lignite quality. These computed surfaces, and their mathematical equations, can be used to predict values of the selected properties of the lignite seams at any desired surface coordinate position between core hole locations. The wide range of application shown by this study indicates that the methods of statistical regression analysis may be useful to evaluate large deposits of lignite or higher rank coal.

Jan 1, 1969

By F. F. Aplan

Separation of the slightly soluble minerals (Ksp? 10-10), one from the other is one of the more difficult tasks confronting flotation engineers. This study has focused on means of separating such prominent members of this class as scheelite, fluorite and calcite from one another. Some experimental work has also been done on the minerals magnesite, dolomite and apatite. Carboxylic acid-type collectors are commonly used industrially to float all of these minerals. Thus, the problem at hand is to ascertain means of achieving selectivity between minerals known to respond rather similarly in flotation. Four techniques have been proposed for the separation of minerals of this class from each other: 1. Control of potential determining ions 2. Use of stereo-specific collectors 3. Use of flotation rate differences 4. Use of selective activating and depressing compounds. This study was directed toward a cursory evaluation of each of these techniques, and each was found to be a possible method of achieving selectivity. Stereo-specific collectors -- those whose parking area may closely match the available adsorption site on one mineral but not on another -- are a possible means of achieving selectivity between scheelite, fluorite and calcite. Stereo-hindered carboxylic acid salts and sulfonates all show selectivity between the three minerals tested. Separations also appear to be possible by the controlled use of the lattice ions (e.g., Ca and [W0=4] for scheelite, CaW04), H+, [OH-, C0-3 and HCO=3]; all of them ostensibly potential determining in the systems studied. Flotation rate differences of the minerals as a function of pH under conditions of starvation collector usage also showed promise. Scheelite and fluorite float most rapidly with sodium oleate in slightly acidic (pH 4-7) solutions whereas calcite floats most rapidly near pH 10. Use of Mn++, Pb++, or other heavy metal hydroxy complexes as activators was seen to effect each of the slightly soluble minerals differently. This is in sharp contrast to the oxygen containing, relatively insoluble minerals, where all minerals respond in a similar manner to such activation procedures. Results indicate that all four methods outlined above may potentially be used to achieve flotation separation of the slightly soluble minerals. More extensive research should be undertaken to detail the spcific applicability of each of the procedures and to make a more complete evaluation of the effect of collector type and concentration, mineral type, pH and size effects.

Jan 1, 1983

By R. L. Soderberg

Large open stopes mined by vertical crater retreat or sublevel s are sometimes backfilled with uncemented sand to support the stope walls and alleviate rock bursts. The failure of bulkheads in two different mines prompted a research project at the Bureau of Mines to prevent a recurrence of these failures. A series of laboratory tests with drains and sand filters was conducted to measure the bulk-head pressures when adequate drainage was maintained. Results showed that bulkhead pressure was reduced to near zero while drains were in operation, as compared to full hydrostatic pressure when drains were blocked or drainage was restricted. A relatively simple, free-draining bulkhead was shown to be adequate.

Jan 1, 1985

By Frank E. Cash

Data on the accident experience of the pebble-phosphate industry in Florida for 1930 and 1940 are combined in this report with statistics for the 9-year period 1930-38, inclusive, which were published in Information Circulars 69173/, 69684/, and 71005/. The periodic compilation and publication of such data enable the pebble-phosphate industry, as well as other industries, to consider the relative hazards, compare experience, and thereby help to prevent accidents. ACKOWLEDGMENTS Accident data were furnished by the following operating companies: Amalgamated Phosphate Co., Brewster; American Agricultural Chemical Co., Pierce; Coronet Phosphate Co., Plant City; International Agricultural Corporation, Mulberry; Phosphate Mining Co., Nichols; southern Phosphate Corporation, Bartow; and Swift & Co., Fertilizer Works, Bartow.

Jan 1, 1941

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

By B. K. Shibler

As a part of the Bureau of Mines' intensive; 'investigation of domestic manganese deposits, ore-dressing studies were conducted on three samples of oxide and silicate manganese ores from various Wyoming properties. The samples wore as follows: 1. A 2-ton sample of ore was obtained by a Bureau engineer during examination of the Caulkins-McGuckin property in the center of Crook County, 10 miles north of Sundance, Wyo. The ore body was described as a vein deposit in rhyolite porphyry. 2. The J. B. C. Mining Co. submitted a 1-ton sample of oxide manganese ore from a property located 44 miles northeast of Rock River in Albany County, Wyoming. 3. A 1-ton sample of oxide-silicate-ore was obtained by a Bureau examining engineer from the Gheen property in the northeast corner of Washakie County, Wyo. The ore body was described as a replacement deposit in a country rock of silicified limestone. As the samples differed widely in physical and chemical characteristics and also in their response to methods of concentration, ore from each property was considered a separate ore-dressing problem.

Jan 1, 1949

By Robert B. Hoekzema

The Bureau of Mines and U.S. Geological Survey completed a 4-yr (1979-82) mineral appraisal of the Chugach National Forest (CNF), AK. This report summarizes the Bureau's placer gold studies in the CNF. Placer mining from the mid-1890's through 1982 produced an estimated 133,800 oz of gold, of which two-thirds was produced prior to 1920. As much as 6,800 oz of placer gold was produced from 1979 to 1982. Most production came from Crow, Canyon, and Resurrection Creeks. Five types of placer gold deposits were identified in the CNF: (1) alluvial placers, (2) bench placers, (3) eluvial placers, (4) glacial placers, and (5) marine placers. Placer sampling indicated a potential for gold production from alluvial and bench placers associated with historically mined drainages such as Crow, Canyon, Resurrection, Sixmile, and Mills Creeks and from unmined drainages including the Avery, Kings, Snow, Copper, and Tasnuna Rivers and several smaller streams throughout the CNF. Results of fineness tests indicated that gold from the CNF ranges from 455 to over 950 fine. Subsequent investigations in drainages with anomalous placer sample values also identified previously unknown lode mineralization.

Jan 1, 1986