Search Documents

By J. E. Tiffany, Z. C. Gaugler

This supplement has been prepared to furnish information on amendments to the regulations that were approved by acting secretary of the Interior on June 24, 1946, while this report was in the press. Page 14, item 2, and page 20, item 4, have been amended by the addition of the following footnote: "Pending the development of a satisfactory multiple-shot permissible blasting unit, a blasting unit of Type II, Class A, covered by Federal Specification WB 411, December 31, 1941 (with or without Amendment 2, June 16, 1945), may be used until Decem- ber 31, 1947. Should a satisfactory multiple-shot permissible unit be made available prior to that date, this interim approval may be terminated." Page 14, footnote / has been amended to read as follows: "The use of charges over 1-1/2 pounds and not exceeding 3 pounds is approved pending further investigation. The approval, which may be withdrawn at any time, expires December 31, 1947, unless renewed. For charges over 1-1/2 pounds, the following additional requirements must be observed: (1) Shot holes must be 6 feet or greater in length. (2) Explosives must be charged in a continuous train with no cartridges deliberately deformed or crushed, with all car- tridges in contact with each other, and with the end cartridges touching the rear of the hole and the stemming, respectively. (3) The permissible explosive must be one showing toxic gas omission that will place it in either Class A or Class B."

Jan 1, 1947

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By John M. Gomes

Two methods for electrowinning tungsten from wolframite [(Fe,Mn)W04] were investigated. The first method, direct electrowinning from wolframite concentrate dissolved in molten salt mixtures composed essentially of various combinations of sodium phosphates, sodium borates, and sodium halides, yielded impure products. The second method was electrowinning from a halide-tungstate melt that was obtained from a high-temperature, two-phase extraction of tungstic oxide (W03) from wolframite. Electrolysis in electrolytes prepared from addition of sodium metaphosphate (NaPO3) and boric oxide (B2O3) to the halide-tungstate melt produced tungsten metal of 99.9 percent purity. Tungsten carbide (WC) was electrodeposited from the halide-tungstate melt when the melt was adjusted to contain 82 mole-percent NaCI and 6.0 mole-percent each of W03, sodium metaborate (Na2B204), and caustic soda (NaOH).

Jan 1, 1970

By Joseph J. Wallace, Lloyd Williams, D. A. Reynolds, James J. Dowd, R. F. Abemethy

"SUMMARY AND CONCLUSIONS1. The investigation shows that the most important beds in Allegany County, from the standpoint of known recoverable reserves are: Lower Bakerstown, Upper Freeport, Upper Bakerstown, Upper Kittraing - less important beds are: Sewickley, Waynesburg, Pittsburgh, and Barton. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated to be 556 million short tons, as of January 1, 1951. Of this total, 304 million short tons is in beds 23 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total eat ted reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand-loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Allegany County, as determined by this investigation, is 49.8 percent. This percentage is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. Based on the weighted average percent recovery for all beds in Allegany County, the recoverable reserves are estimated to be 152 million short tons as of January 1, 1951.4. The Allegany County coals are low-volatile bituminous in rank.5. The Allegany County coals are strongly coking."

May 1, 1953

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

By Benjamin W. Haynes

As part of the first-order assessment of potential manganese nodule processing reject waste materials, the Bureau of Mines estimated the physical and chemical characteristics of reject waste materials that would be generated from each of five potential process flowsheets. These processes were chosen because of their economic and technical feasibility for first-generation nodule processing. A brief description of the five processes is given to show process inputs and outputs, The physical characteristics are predicted based on land-based laterite processing where applicable, and where no land-based analog exists, on the basis of process chemistry. The probable chemical characteristics such as element content and compound form are tabulated for each process for 16 elements: As, Ba, Be, Cd, Go, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn. These elements were chosen based on their presence on the toxic substance list of priority pollutants, EP toxicity criteria, and major and minor elements of economic importance (Co, Fe, Mn, and Mo). Physical and chemical analyses as well as results of the EP toxicity test of one industrially supplied pilot plant reject waste material are presented.

Jan 1, 1982

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By P. L. Woolf

Oil was successfully injected into the tuyeres of the Bureau of Mines experimental blast furnace. Determinations were made for the minimum oil addition necessary to permit the maximum available blast temperature of 2,250° F. and the maximum oil rates at blast temperatures of 1,900°, 2,000°, and 2,100° F. From these tests, the upper and lower levels of high-temperature heat input, which limit the smoothly operating furnace, were established. Substantial coke saving was realized with maximum oil injection. Oil-to-coke replacement ratios have been calculated for various conditions, and oil is compared with natural gas and moisture in somewhat general terms. A study of the effect of variations in slag volume and basicity on the sulfur content of the metal at high sulfur loads was made.

Jan 1, 1963

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By D. W. Bridges, R. O. Dannenberg, Laird Crocker

Preliminary solvent extraction studies , reported by the Bureau of Mines (5) , have been continued and expanded to improve on the previous estimate of process requirements . The solvent extraction portion of the process was examined at a scale large enough to enable meaningful extrapolation of the results to geometrically similar equipment of plant size . About 82 pct of the beryllium was recovered from approximately 0.5 pct beryllium oxide (Be0) Spor Mountain , Utah , ore by a process involving ( 1 ) sulfuric acid leaching , ( 2 ) counter current decantation (CCD ) washing , (3 ) iron ( III) reduction by sodium hydrosulfide ( NaHS ) , ( 4 ) beryllium solvent extraction by di - 2- ethylhexyl phosphoric acid ( EHPA) , ( 5 ) caustic stripping of beryllium- bearing EHPA, (6 ) hydrolysis of sodium beryllate - caustic strip liquor , and (7 ) calcination of beryllium hydroxide (Be ( OH ) 2 ) formed in step (6 ) . The resulting beryllia assayed 98 to 99 pct Be0 and was suitable for most nonnuclear uses . Best overall results were obtained by using pH 2 , 1.6 grams of BeO per liter of leach liquor as feed and 0.25 N EHPA in kerosine containing 2 wt vol pct (grams per 100 ml of solution ) isodecanol ( IDA ) as solvent . Analysis of the data indicated that a commercial plant would achieve 95- pct overall extraction operating at 45 ° C with 20 hp per 1,000 gal of dispersion in each of seven mixer- settlers , having 290 gal per ton of ore hourly mixer capacity and 90 gal per ton of ore hourly settler capacity . At least 79 lb H2SO4 , 13 lb sodium hydroxide (NaOH ) , 3 lb NaHS , 0.25 lb kerosine , 0.07 lb polyacrylic flocculant , 0.03 lb EHPA , and 0.007 lb IDA would be required in H2SO4 leaching and subsequent processing to recover 1 lb BeO .

Jan 1, 1964

Objective To identify techniques to reduce the probability of gob gas explosions. Background In the last 6 years, seven explosions of methane and/or coal dust occurred within worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many mine seals and caused much damage external to the sealed area. Three of these gob gas explosions occurred in one mine in Alabama over a 3-year period. Fortunately, the explosion forces and the toxic gases that vented from the sealed gob area did not cause fatalities or injuries, but they destroyed several large seals. If miners had been inspecting or working near these areas, the potential for serious injury and/or death would have been high. The United Mine Workers of America and the Mine Safety and Health Administration (MSHA) requested that the National Institute for Occupational Safety and Health (NIOSH) help identify the mechanisms for lightning penetration into the gob and recommend ways to reduce the probability of occurrence of future explosions from such lightning penetrations into sealed areas of underground coal mines. Because three of the explosions occurred in a single mine, special attention was focused on these particular explosions. The first occurred in April 1994 in a sealed area, which enclosed about 1.35square miles of abandoned workings (gob). This explosion destroyed 3 of the 38 seals that surrounded the gob. These seals were less than 2,000 ft away from three 4.5-in-diam steel-cased test wells that extended from the surface into the mine entry. At the time of the explosion, the National Lightning Detection Network (NLDN)verified 12 lightning strikes within 10 miles of the mine, including several above the gob. After the 1994 explosion, the damaged seals were rebuilt using an acceptable seal design capable of with standing a 20-psi explosion, as required by 30 CFR 75.335. On January 26,1996, a second gob explosion destroyed five more cementitious pumpable seals less than 2,000 ft away from those destroyed in 1994and even closer to the steel-cased wells. The NLDN verified72 lightning strikes in the area of this second gob explosion. Compressive strength analyses of fragments from the destroyed seals showed that strengths ranged from 11 to 138 psi, with an average of83 psi. This is over 100 psi below the minimum 200-psi compressive strength requirement for cementitious pumpable seals. These seals were again replaced. On July 9, 1997, the third and most violent explosion occurred in the same vicinity of the last two explosions. Three more cementitious pumpable seals were destroyed, including one newer seal that exceeded the minimum 200-psi compressive strength requirement. The NLDN verified 695 lightning strikes above the mine during the time in which the explosion occurred. MSHA's

May 1, 2001

By A. B. Hooker, L. C. IlsLey

Several ignitions or mine pa, which might have led to explosions, and at least ona mine fire attributed to heated leg wires of electric detonators, have occm.rred. at rn1::.es in which outside shot firing is practiced. Photographs taken at one mine ind.la.ted. that the wires became red hot during firing. These results having been --i·-led. to the .Lttention of the electrical section of the Bureau of the Mines, ignitions the tests and to reportd aid in herein preventing were made future to trouble determine of if this possible kind, the cause of The investigation, which 1• considered preliminary, included tests to determine the conditions tha.t cause gas ignitions from heated. leg wires of electric and. of detonators, copper leg possible wires, remedies The tor samples such of heating, wire used. and in the the relative test were behavior the of reg\llar ironDa. Pont iron and copper leg wires (No, 22 A,W,G.) C\1t from Du. Pont electric detonators.

Aug 1, 1922

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989

By Joan Weinberg

The real gross national product (GNP) advanced at a annual rate of 3.1 % during the second quarter, following a revised 3.4% increase in the first quarter (see table 1). Export growth continues to play an important role in the rising output. Combined with the decline in imports, it resulted in a noticeably improved trade position. Imports of consumer goods, including automobiles and food, fell while exports rose. Imported cars have been losing ground to domestic cars. The foreign car share of the U.S. market fell from 36% in October 1987, to 29% in May 1988. Business spending for new plant and equipment contributed strongly to the GNP increase. Equipment purchases, particularly of computers, rose at a 14.8% annual rate, following a large first-quarter gain. Purchases of structures rose 11.8%. The other key component of business spending, change in business inventories, declined from the first quarter. Inventory buildup in late 1987 had been considered excessive.

Jan 1, 1988

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973