Search Documents

By R. A. Beall, W. E. Anable

The purification of hafnium by electron- beam melting at moderate energy inputs and at low pressures was examined in detail . Most metallic impurities and hydrogen were removed in the first few minutes of operation ; oxygen , carbon , and nitrogen were removed at a slower rate . Samples treated by electron bombardment suffered a small loss of weight and a gradual lowering of hardness . The magnitude of each change varied with the energy input and the duration of the melt . Analysis of the data confirms the loss of oxygen as a hafnium monoxide . Approximate activity coefficients for other contaminants are given .

Jan 1, 1964

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

China?s New Steel Complex Postponed. - The planned $5 billion Baoshan Steel Works near Shanghai is being laid aside for 6 months to a year, and may be abandoned altogether. The second phase of construction, in which Wean United, Inc., of Pittsburgh was a major participant, has definitely been cancelled. Over $1 billion had been committed to the 6 million-ton-per-year plant. U.S. Firm Develops South African Fluorspar. - The Armco Bronne Co. of Middletown, Ohio, plans to spend $27 million to develop a fluorspar mine in the Republic of South Africa, With fluorspar reserves at 20 million metric tons, the project is planned to produce 200,000 tons Per year of fluorspar for export starting in 1983. U.S.S.R. Resumes Sales of Titanium Sponge. - Against a background of increased U.S. titanium sponge supplies, the Soviet Union is offering limited quantities of this commodity to the U.S. market at approximately $10.00 per pound, down from $25.00 per pound last year.

Jan 1, 1981

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937

New GSP Trade Status Approved.--President Carter, by Executive Order effective March 30, has approved Generalized System of Preference treatment for imports of nonferrous metal products and other imports from Ecuador, Indonesia, Zimbabwe, Uganda, and Venezuela. As of May 2, Afghanistan and Ethiopia will be taken off GSP status. Under the Generalized System of Preferences, certain imports from developing countries are provided duty-free treatment. A country can lose its GSP status if its shipments of the product exceed $41.9 million or more than 50% of total U.S. imports during the preceding year. However, the President can waive the 50% rule in cases where total U.S. imports of an item in 1979 were less than $1 million. Certain nonferrous imports from Mexico, Peru, Chile, and Zambia are already covered by GSP. Hearings April 10 on International Tin Agreement.--The Fifth International Tin Agreement of which the United States is a signatory, which entered into force on July 1, 1976, will expire on June 30, 1981. A negotiating conference for a Sixth International Tin Agreement will be held under auspices of the United Nations at Geneva from April 14 to May 16, 1980.

Jan 1, 1980

By Paul Biggs

This Bureau of Mines report contains information on 63 water flood projects in Colorado. Water was injected in 10 formations located in 58 oilfields. Specific field data presented include location, discovery, development, water supply, fluid injection, oil and water production, oil reserves, and oil recoveries by primary and secondary methods. An estimated 3.5 billion barrels of water has been injected to recover approximately 533 million barrels of oil, a ratio of 6.57 to 1. Most of the injection water is from alluvial deposits, although produced water is used in many fields. Injection water treatment is not a major problem. Appraisal of project success or failure in this report is based on technical, rather than economic, information.

Jan 1, 1974

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979

By D. S. Kingery

The data obtained from this study cover test areas that are gassy to ultragassy and pillared areas of different sizes and degrees of tightness. The methods of controlling ventilation, applying bleeders, and supporting bleeder entries varied in the different test areas. It was not possible to study all conditions likely to be encountered in coal mines. Undoubtedly, there are areas where bleeder entries, even though properly planned and maintained, might prove unsatisfactory. However, on the basis of this study, the following observations were made: 1. Tests showed that each bleeder system studied provided some movement of air through the pillared area; the quantities of air delivered to the pillar line, ranged from 23 to 82 percent, depending mainly on the extent to which bleeder re-turns were used as main returns from the section. 2. Pressure measurements taken across pillared areas showed maximum pressure drops ranging from 0.05 inch of water for a shallow gob to 2.69 inches for a very deep gob. The pressure differentials varied with the size and tightness of the gob but proved adequate to induce airflow across worked-out areas or through fringes of the gob to the bleeder return system.

Jan 1, 1957

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By Milton H. Fies

The dedication of thin building, establishing a station of the U.S. Bureau of vines at the University of Alabama, bristles with significance and challenges the wisdom and courage of the people of this State. Here is united, in common aim, the Engineering School of our State University, recognized for its competency and usefulness, and the Federal Bureau of Mines. The Bureau is one of the most effective arms of our National Government. It outranks in accomplishment, measured by practical scientific contribution, any like governmental organization in all the other nations. It possesses none of the characteristics of many other bureaus of government which have created popular bias. Here is one Bureau devoid of political suggestion or aim with a personnel zealously devoted to labor in scientific re¬search - an organization marked by practical accomplishment, alleviating many of life's burdens, raking easier life's pathway, and unerringly pointing to life's possibilities.

Jan 1, 1936

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By Charles L. Kimbell

The estimated value of world crude mineral production in 1990 exceeded $1,501.5 billion in terms of current (1990) dollars, or almost $1,160 billion in terms of constant 1983 dollars. This latter figure was 0.3% below the 1989 level and about 3.9% below the record high to date of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. It also provides one of the two statistical bases for this estimation, this being the data on the value of production of a group of key commodities that was compiled for and published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983.1 It should be stressed that the values just discussed and those presented in the tabulation are for crude minerals only, and by no means reflect adequately the role of the entire mineral industry in the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of pro-cessed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,780 billion constant 1983 dollars or $3,600 billion in terms of 1990 dollars.

Jan 1, 1993

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines lid some development drilling at the Milan deposit in an endeavor to find an additional source of supply of copper. The deposit, which is in Coos County, northern New Hampshire, is about 8 miles northwest of Berlin. It was discovered in the seventies and was worked steadily until 1886, yielding a monthly production of 2,600 tons of ore. Lessees opened the mine again in 1695 and mined 1,500 tons. The Milan Mining & Milling Co. acquired the property in 1907 and made regular shipments of ore and concentrates until 1910. From 1911 until 1938, the tract was held by a local resident for timber land, Ventures, Limited, a mining concern with headquarters at 25 King Street, West, Toronto, Canada, acquired the property in 1938. No production has been recorded since 1910. To cut the vein below the old mine workings and to search for extensions to the northeast and southwest, the Bureau of Mines diamond-drilled eight holes for an aggregate of 3,596.2 feet.

Jan 1, 1950

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By John P. Powell, J. L. Eakin

"INTRODUCTION AND SUMMARYNowata County, in the northeast corner of Oklahoma, is one of the principal oil-producing counties of this stripper area. Many fields in the county were opened and much oil was produced before statehood. The location of the major fields, as defined by the Oklahoma Corporation Commission, 2/ the outline of the areas of water-flooding activity, and the location of the several projects described in detail in this report are shown in figure 1.There was some drilling in the county earlier; but it was not until after 1904, when the Secretary of the Interior confirmed as valid the leases granted by the Cherokee Nation, that the major drilling activity began. Initial development in this part of Oklahoma was in the Chelsea field in Rogers County, which adjoins Novata County on the south. The activity spread rapidly northward to the Alluwe and Coody's Bluff fields, and then to the Nowata-Claggett field. Continued exploration resulted in discovery of the Delaware-Childers field, where some wells having an initial production of 1,000 barrels daily were completed. Fields discovered and developed during the next few years included the Lenepah (Elliott), Adair, California Creek, Curl Creek, Woody, and South Coffeyville. The oil-production history of Nowata County is shown in figure 2. In assembling the data for a production curve, it was found that the combined production records for Nowata and Rogers Counties were available for 1914 to 1951, inclusive, and that records for the individual counties were available only from 1926 to 1951, inclusive. The early production figures for the counties from 1905 to 1914, inclusive, except for 1909, were calculated from the initial production statistics of the Federal Geological Survey mineral resources bulletins and production data assembled by C. H. Beal. 3/ The production values for 1905 to 1926 for Nowata County were obtained by dividing the total production for the two counties by a percentage factor derived from known facts regarding the oil industry in the area. Production figures for the individual counties from 1926 to 1933, inclusive, were obtained from the files of the Oil and Gas Journal, and the figures from 1933 through 1951 were obtained from monthly reports of the Oklahoma Corporation Commission."

Jun 1, 1952