Search Documents

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By T. W. Hunter

THE TOTAL production of energy in the United States in 1954 decreased 4.6 percent below 1953. The production of coal continued to decline, and the production of crude oil decreased for the first time since 1949. These decreases were partly offset by an increase in the production of natural gas. The total energy production of 35,365 trillion B. t. u. in 1954 was the lowest since 1950. [ ] This drop in energy production was consistent with the 1.1-percent decline in gross national product during the year-from 364.5 billion dollars in 1953 to 360.5 billion in 1954.

Jan 1, 1958

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By C. Travis Anderson

"Nickel is an essential metal in stainless steel, armor plate, and nickel steels and also in nonferrous alleys, such as monel metal and cupre-nickel, which are used in marine service. Nickel is one of the metals that must be greatly restricted in civilian use to provide the amounts needed for our War program. Consequently, it is desirable to investigate every possible substitute.The 5-cent coin no z in use contains 2.3 percent nickel. At the end of 1941, about 450 tons of nickel was being consumed annually to produce these coins. If the nickel used for that purpose in 9141 had been diverted to military use, 15,000 tons of armor plate could have been produced. As nickel is vitally needed for military as well as essential civilian products, it would seem desirable to substitute some other alloy for the 25 percent nickel alloy now being used. The Bureau of Mines has been asked to suggest possible substitutes.The substitute should have physical properties similar to the alloy now being used. It should have a metallic appearance and ring and a reasonably white color, so to be distinguishable from the present 1-cent coin. It should also be reasonably resistant to corrosion."

Aug 1, 1942

By L. C. IlsLey

The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting,but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely how methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.

Jan 1, 1936

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By W. T. Culler

"The ""rate-of-preduotion curve"" described in the revised Treasury Manual* was devised by the author in May, 1920, and since that time has been use by the oil and gas valuation section of the Treasury Department in determining the rate of production of wells for purposes of taxation. This curve is most useful for estimating the future production of a well, or group of wells, of known daily settled production, where future-production curves and tables based on yearly production records are available. It also provides a means for determining the past year's production of a well of known daily settled production, or conversely, the estimated production on any day for a well of known yearly production.The rate-of-production curve is auxiliary to the production decline curve and is derived from it in estimating the future production of a tract, a production decline curve formed from the records of the tract itself should be used. If such records are not available, and there is no information which leads to the belief that the average production decline of the wells in this tract differs from the average for the pool or district, an average curve for the pool or district may be used.The accompanying chart illustrates a typical rate-of-production curve, with the yearly production decline curve from which it is derived. The production decline curve shown is for an average well in the Augusta district, Butler County, Kansas, and has been constructed from the tables given on page 128 of the revised Treasury Manual.The ordinate (vertical scale on the chart) of any point on a yearly production decline curve represents the production of the well during the year previous to the date shown by the abscissa (horizontal scale). For example, the chart shows that an average well, which produced 100,000 barrels of oil in 1915. produced 92,000 barrels in the year previous to January 19, 1916, produced 53,300 barrels in the year previous to June 1, 1916; produced 49,000 barrels in the year previous to July 1, 1916, 27,000 barrels in 1916, and 10,000 barrels in 1917."

Oct 1, 1921

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently last only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

CESIUM metal production increased sharply in 1963. Domestic Production.--Cesium metal was produced by The Dow Chemical Co., Midland, Mich., MSA. Research Corp., Callery, Pa., and by Penn Rare Metals, Inc., Revere, Pa. American Potash & Chemical Corp., Trona, Calif., produced some combined cesium and rubidium. This company, Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., produced various cesium compounds. Complete production data on cesium and rubidium and their compounds were not available for publication. Consumption and Uses.-Substantially more pollucite was consumed to produce cesium metal and compounds in 1963 than in 1962 but the overall consumption of pollucite continued to be small.

Jan 1, 1964

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By Frank E. Cash

Since ventilation adequate in quantity as well as quality is of paramount importance to the health and safety of men working underground in coal mines, mining officials, employees, and State inspection departments should give it the closest possible attention. MINING LAW OF ALABAMA The law governing, and regulating the operation of coal mines in Alabama was enacted in 1911 and amended or revised in 1923, 1925, 1930, and 1935. The original law and subsequent revisions were progressive steps in safeguarding the health and safety of underground employees.

Jan 1, 1939

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

SUMMARY The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactc rely demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No. 1 Mine in Grant Town, West Virginia. The remote sealing consists of: (1) A sonar initial probing system which can operate satisfactorily even in the presence of dense smoke. The system is capable of determining both the local passageway geometry, identifying the presence of cribs and other obstructions, and the position of the borehole in the mine passage. (2) A mine sealing material system which utilizes fly ash for making the complete seal or as a bulk filler in conjunction with a urethane, froth foam, seal topping system. The choice of using fly ash alone or fly ash with foam topping depends on a number of factors, such as quality of seal desired, time available per seal, depth of borehole, passageway geometry, and water holding require¬ment. The fly ash-foam seal is a better seal, capable of sealing against a higher water head than fly ash alone. The fly ash sealing

Jan 1, 1973

By L. E. Schultze

The Bureau of Mines has devised techniques to recover lithium from geothermal brines as the chloride. More than 99 pct of the lithium was precipitated from a brine containing 170 mg/L Li by adding a solution of AICl3 and increasing the pH to 7.5 with lime slurry. The Li-Al precipitate was dissolved in HCl and sparged with gaseous HCI to recover the AlCl3; this resulted in a solution containing LiCl and CaCI2. The solution was evaporated at 1000 C to obtain a mixture of the chlorides from which 97 pct of the lithium was recovered and 90 pct of the calcium was rejected by leaching with tetrahydrofuran. The LiCl recovered by evaporation of the tetrahydrofuran was purified by dissolution in water and treatment with oxalic acid. The final LiCl solution contained 89 pct of the lithium originally present in the brine and had a purity of 99.9 pet.

Jan 1, 1984

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By James P. Ulery, Frank E. Chase

Clay veins found in coal mines have caused numerous injuries and fatalities. These structures plague all phases of mining, including entry development, pillar recovery, and panel extraction. Clay veins also increase production costs and may disrupt or halt mining. These detrimental aspects have prompted the Bureau of Mines to investigate the physical characteristics of and roof instability problems associated with clay veins. This was accomplished by observing and mapping clay veins in surface and underground mines. The occurrence and origins of clay veins were also investigated to determine predictive capabilities. The investigators found that clay veins normally occur in more stable, less rapidly subsiding coal basins. Clay veins result when tensile stresses develop fissures which are later infilled. These fissures can be propagated by compactional processes and/or tectonic stresses active during and subsequent to coalification. The Bureau also found that associated faults, fractures, and slicken-side planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance, the roof is segmented into cantilever beams, causing unstable conditions. Consequently, the strata on either side of the clay veins should be bolted and strapped together to form a beam.

Jan 1, 1987

By M. S. Oudenhoven

The Bureau of Mines conducted an investigation to determine the theoretical stress distribution in the vicinity of explosively expanded rock bolt anchors independent of their bolts. Plane-strain solutions applicable to this problem were obtained by combining the field pressure with the uniform pressure that would be produced by vertically placed anchors having 2-, 3-, and 4-foot spacings. High rock stress which would be produced by an anchor was localized, as would be expected from St. Venant's effect, and increased as the field pressure decreased.

Jan 1, 1967