Search Documents

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By John L. Ellenberger

The Bureau of Mines investigated the occurrence of slickensides in mine roof in the Pittsburgh coalbed in a portion of the Valley Camp No.3 mine in southwestern Pennsylvania to improve the potential for prediction of slicken-sided zones and determine the orientations of the most prominent slickensided planes. Two distinct types of slickensides were identified; those which were associated with clay veins observed in the coalbed (genetic), and those which were unrelated to any visible structure (nongenetic). The study draws three conclusions: (1) Nongenetic slickensides are not the result of tectonic forces, (2) both genetic and nongenetic slickensides tend to dip at an angle of 30°, and (3) genetic slickensides tend to be alined parallel to the trend of the clay vein and usually dip toward the center of the clay vein. A schematic roof bolting plan is presented that may provide improved roof support where slickensides are present. Roof stability could be improved by supplemental bolting in the direction normal to the plane of slickensides.

Jan 1, 1979

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By John S. Berber

To improve the economics of low-temperature carbonization of coal, the Bureau of Mines is conducting research on the upgrading of the product tar to marketable chemicals. This report describes experiments on the catalytic hydrodealkylation, followed by catalytic vapor-phase oxidation of the dealkylate to phthalic and maleic anhydrides, of mixed residues from the urea adduction of lignite-neutral oil fraction and on the catalytic thermal dealkylation of high-boiling tar acids. The hydrodealkylation experiments were conducted at pressures from 1,000 to 1,750 psig and at temperatures from 600° to 1,000° F. The oxidation was, in all cases, at atmospheric pressure and 9500 F. Maximum yield of maleic anhydride, based on the liquid feed to the hydrodealky1ation unit, was 12.2 percent at 750° F and 1,500 psig; that of phthalic anhydirde was 6.9 percent at 650° F and 1,500 psig. Maximum yield of combined anhydrides was 18.8 percent at 650° F and 1,500 psig. The non-dealkylated feed material, upon oxidation, yielded 8.9 percent and 3.8 percent maleic anhydride and phthalic anhydride, respectively.

Jan 1, 1967

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data oil motor gasolines sold during the minter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular- price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Robert M. Becker

This investigation (in five parts) extends the theory of sample reliability from a sample consisting of a fixed number of items to a sample consisting of a fixed amount of items. Examples of a fixed amount of items per sample are samples consisting of a fixed weight or a fixed volume of unequal size particles. The extension of the theory is confirmed by experimental laboratory sampling using standard procedures. The probability distribution functions (the binomial, hypergeometric, multinomial, generalized hypergeometric, and those here called the compound binomial and compound multimomial functions) are developed from fundamentals. Their distributions are generalized to include some measured characteristic of the items. Infinite population moments are derived from moment-generating functions, and finite population moments are developed from corresponding infinite population moments using a newly defined mathematical operation. The first three experimental moments in laboratory sampling to given weights of particles are compared with the theoretical moments of their corresponding compound mult.inomial distributions. The agreement is striking. The study is divided into five parts. Part 1 deals with probability or random sampling to n items and with all sampling to n items per sample from some one probability distribution. This is the area of sampling covered by well-known theory. Accordingly, the procedures may be different but many of the results are well known.

Dec 1, 1964

By Alvin M. Cummings

"INTRODUCTION During July and August 1943, the Bureau of Mines undertook an investigation of the Trego lead-zinc mine, near the town of Platteville in Grart County, Wis. as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the nation's war program.The Bureau of Mines completed eight churn-drill holes and sampled mineralized faces in the mine workings to determine if further exploitation was justified in an area between the mine and a zone previously drilled to the east.Following the investigation described herein, intermittent operations were resumed. Except where otherwise stated, this report describes conditions only to the time of completion of the Bureau of Mines investigations.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation described in this report was conducted under the immediate supervision of the author and 0. W. Terry, mining engineer of the Bureau of Mines, with the assistance and advice of E. D. Gardner, re¬gional engineer, and E. P. Barrett, district engineer. Final data were prepared under the direction of Paul Zinner, acting chief, Minneapolis Branch, Mining Division.A. V. Heyl, Jr., and A. F. Agnew of the Federal Geological Survey cooperated with the Bureau's engineers and made lithologic studies required during the drilling program.The cooperation of W. N. Smith and O. E. DeWitt of the Vinegar Hill Zinc Co. and Francis Piquette of the Piquette Mining Co. facilitated the investigation to a great extent."

Mar 1, 1948

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure&apos;&apos; or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", “canopies” , "roll bars" , protective structures" and other such descriptive names. In this report, "ROPS" describes the function of the structure; "FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection. “MESA” is used as an abbreviation for the Mining Enforcement and Safety Administration; "USBM" is used to abbreviate the U, S. Bureau of Mines.

By Greenwald, H. P

The Bureau of Mines has been conducting experiments on the explosibility of coal-dust in the experimental mine for more than 17 years. The results have been published from time to time3, and a forthcoming technical paper4 will summarize the results and discuss them in some detail. The present paper will be limited to a statement of the more important facts that these researches have discovered.

Apr 1, 1929

By G. K. Derby

The Bureau of Mines studied the problems caused by airborne contaminants from welding exhaust in surface mining operations and investigated equipment designed to reduce existing hazards. Four commercially available welding-fume exhaust units were tested to determine their effectiveness. Results indicated that the four units had the capability of controlling airborne particulate concentrations and bringing them to within allowable exposure limits.

Jan 1, 1981

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By C. E. Armantrout, H. Kato, M. I. Copeland, M. Krug

The investigation of the nickel - gadolinium phase diagram was undertaken to determine the alloying behavior of these two metals . The data from meltingpoint determinations , thermal analyses , metallographic examinations , and X- ray diffraction analyses revealed a phase diagram with three eutectic points and seven intermetallic compounds . Very limited solubility of the phases in each other was observed . The five phases , Ni Gd , Ni , Gd , Ni Gd , Ni, Gd , and NiGd¸ , melted incongruently at about 1,300 ° , 1,270 ° , 1,180 ° , 1,070 ° , and 775 ° C , respectively . Ni Gd and NiGd melted congruently at approximately 1,550 ° and 980 ° C , respectively . Four of the compounds were determined to crystallize in the hexagonal system : Ni Gd , Ni Gd , Ni , Gd , and Ni Gd . Ni Gd was determined to be cubic and NiGd , orthorhombic . The crystal system of NiGd was not determined . The eutectic points occurred at 13 , 67 , and 85 wt pct gadolinium , and the isotherms at 1,290 ° , 890 ° , and 700 ° C , respectively .

Jan 1, 1964

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular-price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world&apos;s four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By John Campbell, Miller. W. E., G. W. Jones

"INTRODUCTION Because of its interest in accident prevention, the Federal Bureau of Mines has cooperated with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground spaces and has aided in the development of means to prevent such explosions. For several years this Bureau has cooperated with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass.,for the purpose of detecting and eliminating combustible and physiologically harmful gases in manholes in Boston and vicinity.These investigations 5/ have shown that combustible gases from the usual sources — leakage from gas—distributing systems and underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas contamination, termed ""soil"" gases, are present in manholes at times and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric chances affect their production and passage into the manhole. Soil gases usually are abnormally high in carbon dioxide and low in oxygen and contain varying amounts of methane. They are especially dangerous to men entering manholes because they lack sufficient oxygen to support life."

Feb 1, 1940