Search Documents

By R. W. Van Dolah

The feasibility of formulating cap-sensitive slurry explosives for use in underground mines with potentially flammable gas atmospheres was examined. Formulations containing aluminum metal as sensitizer and sodium chloride to reduce incendivity were prepared; some were cap-sensitive and had adequate air-gap. Flaked aluminum metal rather than the atomized type proved to be the more effective sensitizing agent of the formulations tested for incendivity in the large gallery of the Bureau of Mines, some were found to be suitably nonincendive.

Jan 1, 1968

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By Erie C. Donaldson

Gas-displacement tests were made in Berea Sandstone and Arbuckle Lime-stone cores to determine the relative permeabilities to gas, oil, and water for two-and three-phase dynamic systems. Three-phase relative permeabilities were obtained by displacing oil and water from the core with gas and measuring the flow rates of the three fluids simultaneously. It was found that relative permeabilities to fluids in a porous medium are affected by the saturation distributions of other fluids in the medium as well as by their own saturation distributions.

Jan 1, 1966

By Robert C. Gabler

Evaluation of incinerated sewage sludge as a secondary resource for aluminum, phosphorus, and minor constituents such as copper and zinc was initiated as part of the Bureau of Mines secondary resource program. The elemental composition of sludge ash for 14 plants in 11 U.S. cities was determined. Comparing industrialized cities with cities where most of the sewage is domestic, significant differences in heavy metal content were noted. Various parameters were investigated affecting the extraction of metals and phosphorus from a typical industrial city sludge ash and from a Palo Alto, Calif., sludge ash with a high precious metal content. Three extraction-recovery procedures for metals and phosphorus using sulfuric acid leaching, ion exchange, and various precipitation techniques were investigated. The last procedure developed was a combination approach using a three-stage countercurrent sulfuric acid leach that recovered most of the economic values from the sludge ash and also removed the leachable fraction of elements of environmental concern.

Jan 1, 1979

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By Yael Miron

The presence of pyrite (FeS2) in coal can cause or contribute to several problems for the coal mining industry. These problems, which include spontaneous combustion, roof falls, floor heave, and accidental explosions in coal surface mining when ammonium nitrate fuel oil (ANFO) explosives are used, result from pyrite oxidation. Pyrite oxidizes exothermically in the presence of air and moisture to form a large variety of products, including hydrated ferrous and ferric sulfates, and sulfuric acid. Some of the products are reactive chemicals and strong oxidants. The volume of many of these oxidation products exceeds the original volume of the pyrite; as a result, the adjacent coal disintegrates and its surface increases, rendering it more susceptible to oxidation. The heat from pyrite oxidation raises the temperature of the adjacent coal, accelerating the oxidation and self-heating rates of the coal. These combined chemical, physical, and thermal effects are the cause of the aforementioned problems. When ANFO is used in surface coal mines and contacts ferrous sulfate, a highly exothermic reaction ensiles. Additional hazards are fires or explosions caused by the frictional ignition of methane when the pyrite in the coal is struck by a cutting bit during mining.

Jan 1, 1994

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By A. S. Prokopovitsh

A spectrophotometric method for the determination of small amounts of copper in tungsten metal powder using the principle of solvent extraction has been developed by the Federal Bureau of Mines. The metallic sample is dissolved in hydrogen peroxide, tartaric acid added, the pH adjusted, and the excess peroxide destroyed by boiling. Copper is reduced to the cuprous state, and the reagent neocuproine (2,9-dimethy1-1,10-phenanthroline) is added to form a colored complex with the copper. This colored complex is then extracted into chloroform and the absorbance of the separated chloroform layer measured on a spectrophotometer. Copper contents as low as 1 p.p.m. (parts per million) can be determined. The method is limited to finely divided tungsten powder. The interest of the Bureau of Mines in developing more sensitive methods for the determination of trace impurities in high-purity tungsten prompted an investigation of the possibility of using solvent extraction-colorimetric methods. The organic reagents now commercially available make possible many extremely sensitive colorimetric methods for the determination of metallic ions. Extraction of the colored complex into a small volume of organic phase can be used to further increase sensitivity (4) .4/ This general approach has the added advantage that no special equipment beyond that normally found in an analytical laboratory is required.

Jan 1, 1961

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

By B. J. Arnold, F. F. Aplan

"The captive bubble and sessile drop contact angle techniques have been used to evaluate the hydrophobicity of petrographically identified coal macerals. The magnitude of the contact angle on vitrinite is shown to be a function of coal rank ( %C, %0 and % vitrinite reflectance), increasing with increasing rank to a maximum for low volatile bituminous rank coals then decreasing for anthracite. The least data scatter is found when vitrinite reflectance is used as a rank parameter. Contact angles measured or estimated for other discrete macerals, indicate a variation in hydrophobicity based on coal type. These data correlate well with known flotation results. Coal is a heterogeneous mixture of plant remains and associated minerals that have undergone chemical and physical changes by biological and geological processes. These plant remains form coal macerals, discrete organic entities in the coal which have characteristic chemical and physical properties. As the differing chemical nature of each maceral will affect its behaviour in processes such as carbonization the separation of macerals during coal preparation may provide an important asset in coal utilization.Separation of some of the macerals based on specific gravity has been achieved in the laboratory, and by Sun and Cohen , in a study of two Pennsylvania bituminous coal preparation plants. It was indicated that the lighter exinites report almost exclusively to the clean coal while the denser inertinites are concentrated in the higher gravity fractions. The Longwy-Burstlein process6 took advantage of the difference in hardness or friability of the macerals by using impact breakage followed by screening to remove the more friable vitrain,clarain and fusain. The remaining durain, often high in spore content, was then recrushed. The re-mixed fractions produced the optimum size for obtaining the best coke strength for a particular coal.Separation or concentration of rnacerals by froth flotation largely depends on differences in the hydrophobicity of the macerals. Sun and Cohen 5 . indicated an order of decreasing floatability as exinite, vitrinite and inertinite, while a Russian study (as cited by Brown 7 ) showed that vitrains floated more readily than the duller types. More recently, Hirt and Aplan8 showed that 'pseudovitrinite' floats somewhat faster than does vitrinite while fusinite floats very slowly. Olson and A plan found that vitrinite floated easily while substantial quantities of the non-floated coal contained fusinitic material. Burdon noted that vitrinite is more floatable than semifusinite, and Sarker et a/. 11 have shown that vitrinite is selectively concentrated by froth flotation and oil agglomeration. Sun indicated that flotation, based on his calculated floatability index, should decrease in the order clarain, vitrain, fusain and durain; while Horsley and Smith 13 indicated the decrease to be: vitrain, clarain, durain and fusain. These differences can be attributed to the specific coals used in each study and to the individual macerals composing each coal type within a given coal."

Jan 1, 1989

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

By Irving Hartmann, Edward Thomas

"INTRODUCTION Adoption of rubber-tire shuttle cars underground in conjunction with mobile coal-loading machines has introduced new problems in the control of dust on mine roadways. Where this type of loading and transportation is used, development and extraction are generally rapid, with the result that much coal is spilled from the shuttle cars during normal operation, Coal in the roadways from this source and from sloughing of the ribs is ground to fine dust by the wheels of the 'shuttle cars and by the treads of the loading and mining machines. The coal dust usually is somewhat contaminated by pulverized rock, and the mixture could not be loaded with the run-of-mine coal without undue contamination of the product even if it were cleaned up promptly.The presence of large quantities of fine, loose dust, which is constantly stirred up and kept in suspension in air by the traffic, constitutes a grave explosion hazard, reduces visibility along the roadways, and is physiologically harmful to the workmen who breathe the air. From the operating standpoint the loose material is undesirable along the roadways because it provides poor traction for the trucks and thereby increases wear and power consumption. The dust-explosion hazard could be eliminated or reduced by frequent application of sufficient rock dust on the roadbed; but this would not remedy the other difficulties, and in fact it might intensify them. Where practicable, the most direct and effective safety measure is to clean up and remove promptly all dust that forms and settles on the roadways. Unfortunately, in many cases this procedure is not feasible. A third Suggested remedy is to prevent dispersal of the dust into the air and to promote its consolidation on the floor by wetting the dust particles.During the past few years several mines have used calcium chloride on shuttle-car roadways to allay the dust thereon. When exposed to the' humid atmosphere of the mine this salt absorbs Moisture from the air and deliquesces, and in this way wets the dust on the floor of the roadway. In a survey conducted in coal mines in southern West Virginia and in eastern Kentucky where calcium chloride has been in use, somewhat conflicting re- ports were received regarding the merits of the application, and several operators have abandoned the practice either because of actual or assumed disadvantages. The purpose of the study described in this report was to collect and correlate evidence and, on the basis of experimental data obtained in the field and in laboratory tests, to present a clearer picture of the factors involved in the allaying of dust by use of salts."

Sep 1, 1945

By Terry J. Kreidler

In recent years, west-central Arizona and adjacent California have become the focus of geologic and exploration attention because of its excellent exposure of detachment-fault terrane. Detachment faults, normal faults with nearly horizontal fault planes, are the result of regional extension. Rocks on the lower plate consist of mylonitized intrusive, metasedimentary and crystalline rocks highly altered to chlorite; upper plate rocks comprise sedimentary, volcanic, metasedimentary, and metavolcanic rocks. The movement of the detachment fault causes the rocks on the upper plate to be severely fractured and brecciated thus making them Ideal conduits for mineralizing fluids. Mineralization favored the more reactive sedimentary and volcanic rocks of the upper plate. Three gold deposits, located in upper plate rocks, are currently being mined along the Colorado River corridor: the Picacho Mine near Yuma, Arizona, 70 mi south of the study area; the American Girl Mine In southeastern California, 60 mi southwest; and the Copperstone Mine near the southern end of this study area. Samples from the above three mines were used to create a geochemical model of detachment-related gold deposits. Antimony, arsenic, barium, copper, mercury, molybdenum, manganese, tungsten, and zinc all occur In the mine samples in concentrations at least three times greater than found elsewhere in similar rock types. Samples taken by the Bureau from the wilderness study areas contain similar anomalous concentrations of the same elements as well as elevated concentrations of several other elements Including: lead, fluorine, cerium, uranium, and samarium.

Jan 1, 1992

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By P. D. Kovscek

The performance of a novel prototype kerf-cutting impact mining machine was evaluated under a cooperative agreement between the U.S. Bureau of Mines and RAMEX Systems, Bellevue, WA, while operating under conditions typical of normal tunnel entry development. Selected operating parameters were monitored concurrently to determine baseline operating conditions and to study relationships between operating parameters. Using the data obtained, the specific energy requirements of the impact mining machine were calculated and compared to specific energy requirements of tunnel boring machines cutting in rock having similar hardness. Tests results indicate that the kerf-cutting impact mining machine can provide a mechanical means for mining very hard rock that cannot be effectively mined using commercially available mechanical excavators.

Jan 1, 2010

By K. E. Tame

A resume of the history and state of the art of physical beneficiation of uranium ores is presented along with a detailed description of research on concentration of uranium ores by attrition grinding. The information on flotation, gravity concentration, electronic sorting, and selective grinding was gathered to complement the study of attrition grinding methods. Both dry and wet grinding procedures were investigated as potential methods of upgrading a variety of ore types, ranging in grade from 0.02 to 0.42 percent U308. A Mardun4 disintegrator that employs high-speed rotating paddles in a cylindrical shell lined with interrupter bars was used in most of the dry grinding studies. Attrition scrubbing devices, which impart a violent mixing or attritioning action to ore pulps, and cylindrical mills, employing rods or punchings as grinding media, were used in the wet grinding tests.

Jan 1, 1961

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986