Search Documents

Objective To develop a passive, inexpensive technique for monitoring explosion overpressures within sealed areas in underground coalmines. Background From 1994 to 2000, seven explosions of methane and/or coal dust occurred within the worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many seals and caused much damage external to the sealed area. One gob explosion went undetected until the mine operator reopened the sealed area and discovered the damage. Fortunately, these gob explosions did not cause any fatalities or injuries. Because lightning occurs in just about all mining areas, several questions arise. Could gob gas explosions be occurring in other sealed areas and going undetected? If so, what is the magnitude of the resulting explosion overpressures? The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) undertook a study to identify and evaluate passive measuring devices to monitor and quantify the overpressures associated with such explosions. This work was done in parallel with full-scale explosion experiments for evaluating the strength characteristics of seals used for isolating areas in underground coal mines. Approach Evaluation studies were done in PRL's 20-liter explosion test chamber and in the full-scale Experimental Mine at Lake Lynn Laboratory to evaluate the response and accuracy of various commercially available automobile tire pressure gauges to overpressures generated from gas and dust explosions. The first series of tests was done in the 20-liter chamber, which is used to study the explosibility and inerting of fuel dusts and gases. Data from the tire pressure gauge tests were compared to the pressure-time data obtained from the 20-liter chamber 's traditional electronic strain gauge pressure transducer recorded on a high-speed data acquisition system. To evaluate the tire pressure gauges, the valved inlet (tip) of the candidate pressure gauge was removed and the body of the gauge was cemented with epoxy into a 0.25-in pipe elbow and attached to the outside of the test chamber. A second series of tire gauge evaluation tests was done at Lake Lynn during explosion-resistance testing of seals used in underground coal mines. Full-scale seals (20 ft wide by 8 ft high)were constructed as one wall of a 2,000-ft3 chamber and exposed to a series of methane explosions. Average overpressures ranged from20 to 80 psi. The seals were built with various strength materials ranging from 7 to 48 in thick. The modified tire gauges are attached on the outside of the chamber to a 0.25-in NPT pipe that extends into the chamber (figure 1). The axis of the gauge is mounted at a right angle to the plane of the seal to minimize the coupling of any seal movement to the stem of the gauge that may cause inaccurate readings. The internal explosion pressure history is recorded with a strain gauge pressure transducer mounted inside the chamber. Methane is injected into the chamber, mixed with air, and ignited with an electric spark located at the geometric center of the chamber. Maximum explosion overpressures are recorded and compared with the tire gauge pressure.

Jun 1, 2001

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

By Floyd G. Anderson

The increasing trend toward use of continuous-type mining machines created a significant dust problem in coal mining, which resolved itself into three categories: Visibility at face, deposition on return airways, and the potential health hazard. The control measures applicable to these conditions and studied or developed from 1955 through 1957 are summarized and reviewed in this report. Other important problems brought into focus during the same period were radiation exposure in uranium mining and high temperature and humidity. Although temperature and atmospheric pressure alone may not be contributing factors in the incidence of silicosis, the few mining companies who operate under the extremes of these conditions are dust conscious and keep dust-control engineers on their operating staffs.

Jan 1, 1961

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By H. E. Camargo

In an effort to decrease noise-induced hearing loss (NIHL) in coal preparation plant employees, the National Institute for Occupational Safety and Health (NIOSH) is conduct­ing research to identify and control dominant noise sources in vibrating screen (VS) machines. To this end, acoustic measurements of the noise radiated by a dewatering VS were conducted at the Pittsburgh Research Laboratory (PRL) using microphone phased-array technology. These measurements allowed for the identification of the screen as the dominant source in the 250 Hz 1/3-octave band. The sidewalls are the major contributors in the 315 and 400 Hz bands, whereas the eccentric mechanisms and the electric motor are the dominant sources in the 800 and 1,000 Hz bands, respectively.

Jan 1, 2009

By C. E. Jordan

The Bureau of Mines is conducting research into the pneumatic recovery of coarse mica and has used this method to produce mica concentrates that contain more than 90 percent mica. This research is being carried out pursuant to the Bureau's objective to develop technology that will help maintain an adequate supply of minerals and metals to meet national economic and strategic needs. Researchers used a Bureau-designed system of crushers, screens, and zig-zag air classifiers to concentrate coarse liberated mica particles from mica-bearing materials. This pneumatic system was used to concentrate four mica ores from Arizona, North Carolina, and South Dakota and three waste tailings from Alabama, Georgia, and South Dakota. Using these samples, it was demonstrated that plus 65-mesh size mica can be effectively recovered by the pneumatic method. Not only were the concentrates high in mica content; it was also demonstrated that this method can be used to recover up to 78 percent of the mica that was originally contained in the samples. Because it is a dry concentration method, the pneumatic beneficiation technique may be advantageous in areas where water resources are limited.

Jan 1, 1980

By Alexander E. Morrow

Oxygen breathing apparatus for use in mines was introduced to the United States in 1907. Despite their intended purpose of safeguarding lives, the apparatus led to the deaths of many men because of inherent or developed defects in the equipment, lack of training,, physical shortcomings of wearers, and improper procedures. The Bureau of Mines pioneered in research and training to curb logs of life among users of such apparatus and promoted development of safer equipment and procedures. As a consequence, deaths have been far less frequent. In 1944 the Bureau issued Information Circular 7279, Loss of Life Among Wearers of Oxygen Breathing Apparatus. That publication listed the case histories of 26 deaths that had occurred since the introduction of such equipment to American mining. The author, the late G. W. Grove,3/ asserted that further loss of life could be avoided if good equipment were used, teams were properly trained, and the basic principles of safe procedure were followed. This publication is a sequel to I.C. 7279 and contains information on eight deaths among wearers of oxygen breathing apparatus that were overlooked in the original compilation. It also describes the single death that occurred since I.C. 7279 was published.

Jan 1, 1959

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By V. Vallyathan, Xianglin Shi, N. S. Dalai

While Cr(VI) is a known carcinogen, the underlying biochemical mechanism is still not fully understood (1). In a pioneering study Jennette (2) utilized electron spin resonance (ESR) spectroscopy to demonstrate that a long-lived Cr(V) species is generated during the reduction of Cr(VI) by microsomes in the presence of NADPH. Later Wetterhahn and co-workers (3, 4) showed that incubation of chromate with isolated rat liver mitochondria causes the reduction of Cr(VI), as well as the formation of a Cr(V) species. Analogous Cr(V) species have also been detected in the reduction of Cr(VI) by other cellular systems such as Hanserulla polymorphared (5) and blood cells (6, 7). All these as well as other studies (8-12) have suggested that this Cr(V) species plays a significant role in the mechanism of Cr(VI) toxicity. Thus far, however, the chemical structure of this dominant Cr(V) species formed in cellular systems has not been identified, and this observation provided an impetus for the present investigation. Another reason for undertaking this study was that some recent reports (10-16) suggest that hydroxyl ('OH) radicals may also play an important role in the mechanism of Cr(VI) toxicity. In particular, it has been shown that OH radicals are formed in reactions between Cr(V) species and H2O2 (13-16), and that the radical yield depends on the chemical structure of the Cr(V) species (15). For example, while Cr(V)-diol complexes efficiently generate OH radicals, another Cr(V) species, the tetraperoxochromate (CrO3/8) ion, does not (15). Thus in the present study, we focused our attention on the following: (a) structural identification of the Cr(V) species generated in the reduction of Cr(VI) by subcellular as well as cellular systems, using microsomes, mitochondria, and Escherichia coli; (b) possible detection of OH radical in the same systems since there is no earlier report of chromium-mediated generation of 'OH radicals in a cellular system; (c) possible involvement of molecular oxygen in chromium-related OH radical generation since a recent report (17) indicated that Cr(VI) mutagenesis is strongly oxygen dependent; and (d) elucidation of the mechanism of OH radical formation in these systems.

Mar 1, 1992

By John Durkin

A computer model has been generated to evaluate speech intelligibility of individuals wearing conventional and electronic hearing protectors. For speakers talking at normal levels in noise levels of 65 db(Lp) or less, it was found that conventional hearing protectors significantly reduced speech intelligibility. Under the same conditions, electronic protectors provided scores equal to those for the unprotected individuals while providing protection from high noise levels. Therefore, electronic hearing protection is valuable in areas where high noise level is intermittent.

Jan 1, 1979

By E. B. Kester

Of the many angles from which coal can be studied it is evident that some have a direct and others have only an indirect bearing on its physical or chemical nature . The more drastic the treatment employed in an investigation , the more inferential become the conclusions permissible from the experimental evidence obtained . Thus , ultimate and proximate analyses tell something concerning age , behavior on carbonization , and possible industrial usefulness , but nothing regarding structure or composition in the larger sense . Strong oxidation reveals the fact that benzenoid , pyrrol , and furane rings are prevalent in the chemical substances present , and milder oxidation indicates that the mass of coal , as in the case of the peats and lignites , is humic in character . But beyond such points of information , very little additional can be gained by the use of these more or less vigorous measures . To gain wider knowledge of the actual constituents of coal substance as found investigators have worked out systems of separation by means of solvents , of which a large number have been employed at various times both singly and in combination . The list of solvents includes petroleum ether , benzene , toluene , xylene , ethyl ether , alcohol , acetone , carbon bisulphide , pyridine , quinoline , aniline , phenol , tetralin , glycol ethyl ether glycol ethylether acetate , glycol methyl ether , glycol diethyl ether , pine oil , mesityl oxide furfural , benzaldehyde , ethylene oxide , rosin , caustic potash in solvents , amyl alcohol plus pyridine , chloroform , carbon tetrachloride , acetylene tetrachloride , naphthalene , and others . Once a coal has been extracted it has become common practice to subdivide the extract by means of partial solution in other and weaker solvents . Thus , we find the oily and solid bitumens of Fischer ( 1 ) , 3 Bone ( 2 ) and others ; the alpha , beta and gamma constituents of Wheeler ( 3 ) ; the classification of Novak and Hubacek ( 4 ) embracing oils , resins A , resins B , bitumens An , bitumens Bn , and bitumens Cn ; Crussard's ( 5 ) malthenes , asphaltenes , and carbenes , borrowed from asphalt terminology; and the 40 or more subdivisions of the phenol extract of coal worked out by Frazer and Hoffman ( 6 ) . Perhaps the primary object of interest in these many researches has been to find the coking principle of coal , and to study it and to learn why certain coals form hard , wellfused cokes , and others merely fall to pieces during carbonization . The origin of the various constituents of the gas and tar , the temperature at which each forms , and something of the mechanism of their synthesis have also been sought , as well as new bases for adjudging rank .

May 1, 1931

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By Irving Hartmann, F. P. Christofel, John Nagy, E. B. McGibbeny

"INTRODUCTION When permissible explosives are used in c procedure recommended by the Bureau of Mines 5/ they are relatively safe, and, no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. 6/The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite flammable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere. 7/Research in the Experimental coal mine 8/ of the Bureau of Mines at Bruceton, Pa., and unfortunate experience in commercial mines have proved beyond doubt that improper use of explosives that have passed the official permissibility tests can cause as explosions. In limited tests with a fey American permissibles at Bruceton, and in more, extensive tests with permitted explosives at the Polish experiment station, 9/ explosive charges were fired from steel cannon and freely suspended in coal-dust clouds. In these experiments coal dust was ignited under some conditions. However, it has never been definitely established whether permissible explosives can initiate coal-dust explosions when fired in a coal seam. It is true that a few mine explosions were strongly suspected to have resulted from ignition of coal dust by misuse of permissibles, but in each case other complicating factors introduced some doubt in the minds of the investigators. Full knowledge of the problem is important, because coal dust is present in most blasting operations in coal."

Apr 1, 1952

By H. E. Hilliard

A method was investigated for detecting and counting filamentous iron bacteria in open recirculating cooling systems. It is simple and fast and does not require trained microbiologists. Samples from 26 systems were examined. Cells were cultivated on commercially prepared ready-to-use media. Cultures grew well on this medium and were identified as filamentous iron bacteria by microscopic examination and by their ability to deposit iron using the prussian blue reaction.

Jan 1, 1976

By R. C. Ellman

This report presents results of a series of tests on grindability of lignites and factors that influence grindability determination. All grindability tests in this investigation were made in the standard Hardgrove test apparatus. In addition to tests on standard samples of equilibrium moisture content, grindability determinations were made on air-and oven-dried samples of lignite representing the complete range of moisture content from normal bed moisture to nearly moisture-free conditions. Grindability index for all tests was calculated both by standard method and by an alternate or "corrected" method of calculation based on directly measured weight of fine-particle material produced in the grindability test. The second method of calculation allows more satisfactorily for loss of moisture during testing of high-moisture samples.

Jan 1, 1955

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961