Search Documents

By Launa Mallett, Charles Vaught, Michael J. Brnich, R. Lincoln Derick

After thoroughly covering the health and safety training subjects required under Title 30, Part 48, of the Code of Federal Regulations (CFR), mine operators often find themselves with little or no time left in the class schedule for other important topics. This paper discusses a technique developed in partnership with RAG Twenty mile Coal Co., Oak Creek, CO, for incorporating employee participation at all levels in fire prevention and safe equipment operation training outside of traditional classrooms. The process involves development of training modules consisting of short, 5- to 7-minute videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner’s workplace.

Jan 1, 2002

By Alice V. Peter

Meerschaum or sepiolite is employed principally in tobacco pipes and cigar and cigarette holders, although a few other uses of minor importance are Down. The unique value of a meerschaum pipe is derived from the owner's pleasure in watching the color deepen with smoking and in having the color "set" at the desired shade. The name "meerschaum" (German for "sea foam") is applied because the material, when pure and dry, will float on water. Owing to its resemblance to the porous, bonelike structure of the cuttlefish, or septa, it is also known as sepiolite. There are a few scattered deposits of meerschaum in. the United States which have yielded a small product ion, but the world's supply of the' material is obtained fined principally from Asia Minor, Meerschaum deposits near Eski-Shehir, Turkey, are said to have been worked 2,000 years ago, but commercial exploitation is a development of the last hundred years DESCRIPTION AND PROPERTIES Meerschaum is a hydrous magnesium silicate (H4Mg2Si3010) having the following theoretical analysis: Si02, 60.8 percent; MgO, 27.1 percent; H20, 12.1 percent. It is a soft. (H.2 - 2.5), fine-grained, earthy, white, gray, or yellow material. It is very light weight when pure (specific gravity, 1 to 2) and is highly absorbent. Because of its porosity the proportion of water present in the mineral is affected by the humidity'of the atmosphere. In a moist atmosphere the water content may be as much as 21.7 percent. Then wet the material is soft and somewhat plastic. When dried again it becomes lard and tough. The toughness is especially apparent in some forms that have a fibrous or leathery texture.

Jan 1, 1934

By Jack E. Fraley

The Bureau of Mines has successfully developed and tested a machine for spraying sealant onto coal mine roof and ribs. Dry material is transported pneumatically to a water-adding nozzle designed to provide dust-free spraying while being nonplugging and self-cleaning. The machine is self-cleaning, 35 inches in height, and capable of applying l/2-inch-thick coatings at over 1,000 ft2/hr.

Jan 1, 1978

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

By W. S. Sanner

Grinding experiments were conducted to determine the finest anthracite particles that could be produced in a ball mill. Continuous and batch tests were run in a dry-grinding ball mill. Batch grinding produced the finest coal particles. They averaged 2.2 microns in diameter and were 99.0 percent smaller than 37 microns. Continuous grinding yielded a product 6.1 microns in diameter, with 96 percent smaller than 37 microns.

Jan 1, 1968

By L. W. Brandt

As part of its objective to expand the body of mineral information as a basis for new technology, the Bureau of Mines conducted research on the fundamental behavior exhibited by phosphate clay waste in settling ponds. A semiempirical equation used to describe the compaction of ceramic powders in a single-acting die was applied to aqueous phosphatic clay waste and attapulgite slurries. This equation, [*V = a1 e ?k1/P + a2e ? k2/P] was found to describe the compaction of an attapulgite gel and a phosphate slime gel by a moving screen. [*V] is the ratio of the compaction achieved at a given pressure, P, to the compaction achieved at a pres-sure sufficient to remove all space between particles. The constant al represents the fraction of compaction achieved at low pressure by rearrangement of floes to higher packing density, and a2 represents the fraction of compaction achieved at higher pressure resulting from removal of voids within floes. K1 and K2 are constants determined from the experimental data. Both the low-pressure and high-pressure compaction mechanisms were observed in the compaction of the clays. These two compaction mechanisms offer an explanation for the observation that impounded slimes initially dewater rapidly and then dewater at a much slower rate.

Jan 1, 1982

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

By E. L. Sweeney

The mine and mill of the Davis-Dunkirk Lines, Inc., are about 16 miles by road south of Prescott, Ariz., which is the nearest railroad point for receiving mine and mill supplies and for shipping concentrates to smelters. A good trucking road reaches within 2 miles off the property, but from that point the grade is very steep. Outgoing loads are limited to 2 tons. The topography near the mine is exceedingly rugged, and the area is slightly wooded. The climate is mild excepting in a few winter months, when the snowfall is heavy. Electric power is secured by way of a 4 1/2-mile, high-tension line connecting with the main line of the Arizona Power Co. The concentrator was intended to treat 60 tons or more daily of gold-silver-copper ore and make a single gold-silver-copper concentrate for shipment to a copper smelter.

Jan 1, 1933

By A. W. Deurbrouck

Four samples of Pittsburgh-bed coal, of various size consist and ash content were dewatered in a pilot-size vacuum-disk filter partially enclosed with a steam jacket. Steam fed at 2.5 to 12.5 pounds per minute reduced the moisture content of the filter cakes from 2.8 to 13.8 percentage points more than normal vacuum dewatering. Approximately 1.5 pounds of steam was required to remove 1 pound of water.

Jan 1, 1966

By A. L. Murray, D. Harrington

From 1870 to the end of 1929 the coal production of Utah has been some- what less than 110,000,000 tons. During this period at least three major disasters have occurred with fatalities totaling about 380, establishing a decidedly bad record of approximately 3.5 persons killed by major mine explo- sions per million tons of coal produced. Even during the period when there have been no disasters, such as the years 1914 to 1920, inclusive, the fatalities in ordinary working were about 5.4 per million tons produced, against 3.7 per million tons for the whole United States for the same years. The 5-year period following the World War, 1918 to 1922, inclusive, had 4.7 fatalities per million tons; hence, the fatality record in the coal mines of Utah has uniformly been in excess of the average of the coal mines of the entire country. Notwithstanding this poor record, Utah has given to the coal-mining world many excellent safety methods and practices, and Utah coal mines in general take greater measures toward safe mining than do the coal mines of any other State; if practices and methods allowed and pursued in coal mines of other States were tried in Utah coal mines, there would be a succession of disasters.

Nov 1, 1931

1. In 2002, a total of 2,065 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.2% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,910) and anthracite mines 7.5% (n = 155) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (28.7%), West Virginia (21.7%), and Pennsylvania (20.1%).

Jan 1, 2004

By J. J. Burns

Disasters such as occurred at Oppau, Germany, in 1921, at Tessenderloo, Belgium, in 1942, and in this country at Texas City, Tex., in 1947 clearly indicate the explosive hazard associated with the manufacture, storage, and transport at ion of ammonium nit rate The importance and extent of the hazard may be Judged from the large amount of ammonium nitrate produced and transported annually in this country. Between July 1, 1947, and June 30, 1948, it was estimated that the United States produced 461,528 tons of ammonium nitrate commercially for agricultural purposes alone .5/ In addition, U. S. Army Ordnance plants have manufactured and shipped 779,730 tons of ammonium nitrate fertilizer to Germany, Japan, and Korea.6/

Jan 1, 1953

By A. R. Taylor

The Bureau of Mines has determined the heat capacity and enthalpy values for beryllium sulfate (BeS04) throughout the temperature ranges of 10° to 300° K in an adiabatic calorimeter, and 350° to 860° K in a Bunsen-type ice calorimter, The heat-capacity data were extrapolated to 0° K, and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were reported at 10-degree intervals between 0° and 300° K. The method of least squares was used to fit the enthalpy data with an algebraic equation. The equation also was used to calculate values of heat capacity, entropy, enthalpy function, and free-energy function at 50-degree intervals between 300° and 900° K.

Jan 1, 1963

By D. L. Sawyer

Aqueous C12-02 leaching procedures developed by the Bureau of Mines to produce zinc chloride from zinc sulfide bulk concentrates were effective in extracting 99 pct of the zinc and 97 pet of the silver contained in samples of massive seafloor sulfides from the southern Juan de Fuca Ridge. Zinc sulfide (sphalerite and wurtzite) mineralization comprised 55 and 88 pct of two specimens provided by the U.S. Geological Survey for this study. Minor occurrences of galena, chalcopyrite, and other minerals in the sulfides permitted the recovery of pregnant liquors that were low in metal values other than zinc, which were successfully purified by a two-step cementation procedure using zinc dust.

Jan 1, 1983

By Robert A. Jankowski

The U.S. Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the mining industry, has identified and demonstrated the effectiveness of several improved face ventilation techniques for longwall mining systems. These include the following: identifying improved techniques for measuring face ventilation parameters on longwall sections, installing curtains at the intake end of the longwall face to maximize usage of the primary airflow, identifying optimum face airflow rates for maximizing dilution effects, and coursing the primary face intake from tailgate to headgate to minimize outby airflow contamination. Application of these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1993

By A. E. Isaacson

The U.S. Bureau of Mines determined the effect of common sulfide minerals on the corrosion rates of various types of ferrous alloy grinding media. Data obtained from this study will aid in determining the contribution of any electrochemical reactions between sulfide minerals and grinding media to the total grinding media consumption. Common sulfide minerals used in this study were chalcopyrite, galena, and sphalerite. In the presence of oxygen, chalcopyrite was found to increase the corrosion rate, galena was found to decrease the corrosion rate, and the effect of sphalerite was dependent upon the type of grinding media. Possible electrochemical reactions of these minerals in the presence of grinding media are suggested.

Jan 1, 1989

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

By Gwendolyn D. Hood

The U.S. Bureau of Mines developed a dewatering technique for treating wastewater that was tested on waste slurry from a commercial tile company in Alabama. Raw wastewater samples were pretreated with 10 Ib calcium chloride and 10 lb Wyoming bentonite per 1,000 gal of slurry. After pretreatment, polyethylene oxide (PEO) at dosages varying from 0.05 to 0.20 lb per 1,000 gal was mixed with the waste slurry, forming strong, tough floes that were separated from the clarified water using a trammel. The flocculated slurry was dewatered to a consistency that could be handled for subsequent disposal in a landfill. The clarified water quality was equivalent to that of the company's present treatment system.

Jan 1, 2010