Search Documents

By R. E. Campbell

Uranium metal of improved purity was prepared by electrorefining commercial magnesium-reduced uranium in a molten sodium chloride-uranium trichloride electrolyte. The best operating conditions for the preparation of refined metal were established as follows: an electrolyte containing 8.7 to 13.3 weight-percent uranium; initial cathode current densities from 300 to 1,500 amp/sq ft; and a molten salt temperature of 860° C. Ingots produced from electrorefined uranium crystals prepared with these operating conditions were substantially free of metallic impurities. The only impurities in the refined and consolidated metal were present in low or undetectable amounts.

Jan 1, 1965

By Helen W. Lang

The Bureau of Mines has developed a very rapid gas chromatographic method for routine determination of oxygen, nitrogen, methane, and carbon dioxide in mine atmosphere samples. Analysis is accomplished in 3 min; readout appears on a single strip chart. The gas sample is split between two columns contained in separate chromatographs. A 5 A molecular sieve column separates oxygen, nitrogen, and methane; a porous polymer column separates carbon dioxide from an air peak. Direct selective analysis of methane from this unresolved air peak is accomplished using a hydrogen flame ionization detector (FID). Carbon dioxide is catalytically converted to methane and detected by FID.

Jan 1, 1972

By C. M. Frost

Crude shale oil prepared by gas-combustion retorting of Colorado oil shale was hydrogenated over a cobalt molybdate catalyst at an operating pressure of 1,000 psig, temperatures of 781° and 761° F, and liquid hourly space velocities of 0.10 and 0.05 Vo/Vo/hr, respectively. The yields of total liquid products and the amounts of nitrogen and sulfur removed were comparable with those obtained at an operating pressure of 3,000 psig and a liquid hourly space velocity of 1.0 Vo/Vo/hr. Approximately 1.5 times as much gasoline was produced at the lower pressure and space velocities.

Jan 1, 1973

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

By BUREAU OF MINES

The approval of the U. S. Bureau of Mines when granted to a manufacturer for a gas mask is a certification that the particular device has been submitted to the Bureau of Mines for inspection and test and has been found to meet that bureau's published minimum requirements for safety , durability , and satisfactory performance . Any de- Gas masks are approved by the Bureau of Mines only as a complete unit or assembly of parts , as canister , facepiece and harness . This is in order that responsibility for rigid adherence to the bureau's requirements may be definitely located and not divided . vice marketed under this approval must be a unit composed of parts identical in detail of design , assembly , workmanship , and quality , and produced under the same control and inspection as the original device to which approval has been granted . The particular parts which comprise the approved assembly are designated in a letter to the manufacturer at the time the approval is granted . In recent years they are also specified in the approval plate authorized for use in connection with the sale of the device . Each part permitted in the assembly is legibly marked by name or number for the guidance of users of masks in ordering and identifying approved parts when making repairs , and thereby maintaining their equipment as an approved device . In view of the foregoing , any change in the design of parts or deviation from the permitted assembly of parts would violate the conditions under which approval was granted and the device would not be considered as meeting the approval requirements of the Bureau of Mines . The U. S. Bureau of Mines has been frequently requested to interpret the approval status of a gas mask assembled from parts which have separately met its requirements as components of two or more approved devices but which in the form of a complete unit has not been submitted for tests or been granted approval . Responsibility for the elements and for their proper assembly is in such case divided . Such assembled units have no status as permissible equipment under the Bureau of Mines system of schedules . The reasons underlying this policy are that the approval is granted only to some one who assumes responsibility for the whole and that the details of assembly and coordination of parts are considered to be important to the satisfactory performance and safety of the device .

Sep 1, 1932

In response to increased aluminum demand, U.S. producers have begun reactivating primary aluminum capacity which was shutdown during the 1974-1975 recession. Reynolds Metals Company started up almost 80,000 tons per year of idled capacity at Listerhill, Alabama, and Jones Mills and Arkadelphia, Arkansas plants. Howmet Aluminum Corporation and Alumax announced that the operating rate at their jointly owned facility at Frederick, Maryland was being increased from 75 percent to 100 percent, equivalent to a 44,000 ton-per-year increase in output. Kaiser Aluminum and Chemical Corp. expected to restart one of the two idled potlines at its Mead, Washington facility in May raising its production rate by 27,000 tons per year. ANTHRACITE - The anthracite market for the larger sizes continues at a good level, and although the demand for industrial sizes has been weak, the current trend indicates an increased demand for industrial fines by the steel, auto, and other industries.

Jan 1, 1976

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook, it is clearly impossible to cite all sources of information used in its presentation, but some recognition seems due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of our counterpart agencies throughout the world. Information they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1993

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By W. G. Pariseau

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. The present study uses rock deformation measurements to validate and calibrate a geomechanical model of the experimental Lucky Friday underhand longwall (LFUL) stope on the 5,100-ft level of the Lucky Friday Mine, Mullan, ID. The calibrated three-dimensional, finite-element model and measurements of rock mass displacement show a correlation of 0.795. The calibration reduces rock mass modulus to 14 to 17 pet of laboratory values and rock mass strength (with an energy rule) to 37 to 41 pet of laboratory values. This model suggested that stress-related ground control problems would be encountered west of the stope where the vein makes a right-angle turn and then splits. Rock burst activity was concentrated in this area during mining of the LFUL stope.

Jan 1, 2010

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By J. L. Ambs

The U.S. Bureau of Mines (USBM) Diesel Research Program emphasizes the development and evaluation of emission control devices to reduce exposure of miners to diesel exhaust pollutants. Studies by the USBM have shown that diesel exhaust aerosol (DEA) contributes a substantial portion of the respirable aerosol in underground coal mines using diesel equipment not equipped with emission controls. The USBM and the Donaldson Co., Inc., Minneapolis, MN, have developed a low-temperature, disposable diesel exhaust filter (DDEF) for use on permissible diesel haulage vehicles equipped with waterbath exhaust conditioners. These were evaluated in three underground, mines, to determine their effectiveness in reducing DEA concentrations. The DDEF reduced DEA concentrations from 70 to 90 pct at these mines. The usable life of the filter ranged from 10 to 32 h, depending on factors that affect DEA output, such 'as mine altitude, engine type, and duty-cycle. Cost per filter is approximately $40.

Jan 1, 2010

By Maria I. De Rosa, Charles D. Litton

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000°C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 1992

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995