Search Documents

By Irving Hartmann

The fire end explosion hazard of excessive coal-dust deposits in mines has been recognized for many years, and important measures have been developed for reducing dust formation and to alley loose dust near its source. Nevertheless, in the course of normal mining it has been estimated that 1 to 3 percent (in some thin, friable seams up to 10 percent) of the total coal mined is reduced to dust of through-20-mesh fineness. In highly mechanized, continuous mining operations the production of fines is even greater. Most dust is trapped near its point of origin and removed from the mine, but large quantities are transported by the air current and by haulage into entries, where the greatest proportion settles on the floor and the balance on the rib and roof surfaces. The latter is generally finer in particle size than the floor dust; this, coupled with its more advantageous position for dispersion, makes the rib-roof dust (also to be referred to as overhead dust) a greater potential explosion hazard.

Jan 1, 1954

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By C. H. Elder, Fred N. Kissell, S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By Paul T. Allsman

SCIENTIFIC inquiries concerning phenomena that may influence mining technology were widely publicized during the year. The deep-hole drilling project "Moho," 3 the use of nuclear explosives underground, and the recovery of minerals from the depths of the sea became subjects of scientific and general discussion. The mining industry continued to watch these developments with keen interest: but its more immediate concern was the increasing tempo of competition between mineral commodities, the domestic producers of these commodities, and foreign sources of supply. The competitive situation has intensified the industry's efforts to develop more efficient new mining methods, as well as to improve the efficiency of present practices. The attitude of the industry was well illustrated by rapidly expended use of low-cost ammonium nitrate explosives, the establishment of rigid schedules for equipment maintenance, and close attention to the detailed costs of production. The complexity of planning a new coal mine is aptly illustrated by the editors of Mechanization in the April 1959 Issue, in which they outline the cost of developing a mine and the various problems, factors, and decisions involved.4

Jan 1, 1960

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By John D. Corrick

A dilute sulfuric-acid leach was developed for extracting lead and copper from lead blast furnace mattes and the chemistry was defined. The possible application of Ferrobacillus ferrooxidans to the problem of salvaging lead and copper from blast furnace mattes was also investigated. Operating conditions were varied to determine their effect on the oxidation and hence extraction of lead and copper from the matte. Conditions varied were temperature, pH, reaction time, aeration in the slurry, and particle size of the matte. A set of optimum conditions were developed that resulted in maximum lead and copper sulfide oxidation. Tests employing these optimum conditions resulted in 82.3 percent of the lead and 98.7 percent of the copper being extracted by a dilute acid leach, while maximum lead and copper extracted using F. ferrooxidans was 69.8 percent of the lead and 78.4 percent of the copper. Tests conducted with a different sample of blast furnace matte indicated that the dilute acid leach might have wide application in extracting lead and copper from other such blast furnace mattes.

Jan 1, 1968

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By W. F. Marshall

The Bureau of Mines conducted a series of experiments to determine the influence of exhaust rebreathing on emissions from various gasoline and diesel engines. Tests were conducted that simulated operation of engines in nonventilated spaces as well as in spaces with partially restricted ventilation. Results of these tests showed that exhaust rebreathing can have a marked effect on exhaust emissions and thus on the composition of the air in the working space. For the case of restricted ventilation, unacceptably high (greater than 50 ppm) levels of CO in the air of the working space resulted from exhaust rebreathing rates as low as 8 pct exhaust in the engine's intake. Operation in a nonventilated space resulted in highly critical CO levels (fatal in a few minutes) at times corresponding to 1 to 3 pounds of fuel consumed per 1,000 cu ft of space. Tests involving spaces of various sizes showed that volume of the air space [per se] is not important--the primary variable is fuel consumed per unit volume of air space.

Jan 1, 1973

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By Gerrit V. R. Goodman, Fred N. Kissell, Charles D. Taylor

In This Chapter [Methane emission peaks Exhaust line curtain or duct The spray fan system Dust scrubbers with blowing ventilation Dust scrubbers with exhaust ventilation The ventilation of abnormally gassy faces Methane detection at continuous miner faces Ventilation and methane detection at bolter faces and Reducing frictional ignitions] This chapter gives guidelines for preventing methane gas explosions at continuous miner sections in coal mines, both at continuous miners and at roof bolters. The need to control peak methane emissions is particularly stressed. Emphasis is also placed on ventilation principles, monitoring for gas, and reducing frictional ignitions. METHANE EMISSION PEAKS Methane emission from the coal at continuous miner faces varies considerably. Plotted on a chart, methane emissions consist of a series of peaks and valleys corresponding to the cutting cycle of the mining machine, with the methane concentration spiking as the machine cuts into the coal (Figure 3–1) [Kissell et al. 1974]. These methane peaks can be substantial. For this reason, efforts to safely dilute the methane must focus on the level of the [ ]

Jan 6, 2006

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20 ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation. For both explosives, C4 and TNT, peak pressure decay with travel down the entry was inversely proportional to distance to the 0.9 power. When comparing pressure measurements at 200 versus 100 feet from the detonation; at 200 feet the pressure would be 1/2 0.9 or 54 percent of that measured at 100 feet. By comparison, peak pressure for a surface shot exhibits a decay with distance to the -1.6 power, yielding a pressure at 200 feet 1/2 16 or 33 percent of that measured at 100 feet. This result confirms that the blast wave from detonation of an explosive in an underground mine maintains its force for a greater distance than would be the case on the surface. Table and figures follow the text.

By W. H. Ode, F. H. Gibson, W. A. Selvig

The great expansion of production of aluminum for war purposes has aroused some concern regarding the available supply of carbon suitable for making carbon electrodes required in the electrolytic aluminum process. Approximately three-quarters of a pound of carbon electrode is consumed for each pound of aluminum produced. 5 Because of its small amount of impurities and its suitable physical characteristics, calcined petroleum coke is the standard material used by the aluminum industry for making electrodes As it may be necessary to use some substitute materials, the possibility of using coke made from coal has been considered. Besides this possible use, information concerning the source of low-ash coals is of general interest. Specifications of the aluminum industry for calcined petroleum coke suitable for the manufacture of electrodes are very stringent in regard to allowable impurities. In one such specification the maximum allowable ash is 1.0 percent; the maximum allowable content of iron (as Fe) is 0.06 percent and that of silicon (as Si) is 0.08 percent; the maximum for cal- cium (as Ca) and for sodium (as Na) is 0.12 percent for each, but the two combined may not exceed 0.12 percent; maximum allowable sulfur is 2.0 per- cent. The presence of barium, nickel, chromium, manganese, cobalt, or vanadium is objectionable, and only extremely small amounts are allowed. In regard to physical properties, the coke is required to be so thoroughly calcined that it has a real density of at least 2.02.

Nov 1, 1943

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966