Search Documents

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

3. Preliminary Evaluation of Mine Sealing Techniques As the first stage in the development of a technique for the remote sealing of mines, a state-of-the-art survey of various mine sealing techniques was conducted. This was expanded to include a review of different materials offering some potential for use as a mine sealant. Techniques for the remote placement of materials for other applications were evaluated, and system concepts for dis¬tributing remotely placed materials were developed. This preliminary review led to the development of a functional description of a general mine sealing technique to meet the specified conditions. Various potential system configurations were synthesized. These were subjected to a preliminary evaluation based on estimated confidence in system performance, development risk, cost, and sealing time. Based on this preliminary evaluation, promising mine¬sealing techniques were selected for further development. This section presents a review of the following: (a) Techniques for constructing permanent seals from within a mine. (b) State of the art in remote sealing for mine fire control. (c) Techniques for remote placement of materials for other applications. (d) Systems for distributing remotely placed material. (e) Materials for mine sealing. (f) Synthesis of remote mine sealing concepts.

Jan 1, 1973

Promote safer and more efficient mine operations by providing communications between personnel located anywhere in the mine. Approach A radio communications system was designed which takes advantage of existing mine wiring such as telephone lines or electric power cables. The existing wiring distributes radio signals throughout the mine, making communications possible between roving miners, vehicle operators, dispatchers, and other personnel. How It Works Research has shown that medium frequency (MF) signals (300 KHZ-3 MHZ) can couple onto and re-radiate from nearby conductors. This effect is known as parasitic coupling and re-radiation. In a mine, these conductors include electric power cables, control lines, telephone lines, trolley lines, as well as metal water and air pipes Since all underground mines require these conductors for normal operations, the necessary network already exists and expands automatically as the mine is developed. A radio communication system has been developed that uses the parasitic coupling and re-radiation characteristic of MF. Using this system, whole mine radio coverage can be achieved without the need to install or maintain communication lines. The system consists of mobile transceivers for roving personnel and vehicles, and fixed-location base radio stations and repeaters.

Jan 1, 1982

By T. A. Sullivan

Research undertaken by the Bureau of Mines in 1938 has resulted in the development of titanium from a laboratory curiosity to a commercial metal. Along with processes for producing the metal, it was necessary for the Bureau to develop methods for analyzing the metal, raw materials, and intermediate products. Some of the methods developed have been published.3 4 5/ General Services Administration (GSA) was responsible for purchasing titanium metal under Defense Production Act contracts with commercial producers. GSA designated the Federal Bureau of Mines to analyze this metal and establish its compliance with Government specifications. A substantial quantity of tin was found in some of the samples analyzed, and in July 1957 tin was added to the list of impurity elements to be determined. The specifications limited the amount of tin in titanium sponge to a maximum of 0.10 percent. A program was immediately initiated to investigate methods and techniques for determining tin in the range of 0 to 1.0 percent. A method accurate at the 0.10 percent level was necessary, as this level was the critical range for acceptance or rejection of the metal.

Jan 1, 1960

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By McHenry Mosier

The Bell mine operated by the Warner Co. at Bellefonte, Pa., has an annual production of about 600,000 short tons of high-grade limestone. Since 1924, shrinkage stoping has been the mining method. Horizontal, long-hole diamond-drilling for production in stopes was started with one machine in July 1946. It is now standard practice. The burden on the holes is 10 feet. Diamond bits are noncoring EX-size in both concave and pilot types. The two types have little difference in drilling speed at the Bell mine. The diamond drills are mounted on 3-inch single-screw columns. Diamond drilling shows a marked increase in efficiency at the Bell mine, compared to percussion drilling, with respect to tons broken per drill shift, tons broken per foot of hole, and tons broken per pound of explosive. The advantages of diamond-drilling blast-holes also include (a) improved safety, greater footage per drill shift, (c) better frag- mentation of the broken, stone, and (d) reduction in amount of barring down required in stopes because the working places are limited to slots which have a relatively small area.

Feb 1, 1948

By F. D. DeVaney

In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley Experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Linn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Joseph and Kinney in writing about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say: "***It has been estimated that 26 to 35 million tons of ore contain 5 to 35 per cent of manganese, and the total domestic tonnage is from 75 to 48 million tons. The mean of these values is 30.5 million and 42 million tons, so it is seen that about 75 per cent of the reserves are in Minnesota." The manganese-bearing ores of the Cuyuna district maybe roughly grouped into two classes. The most abundant ore is of the low-silica, low-manganese, and high-phosphorus type called brown are. The other type is the so-called black ore, which is characterized by a higher manganese and silica content and by a lowe phosphorus analysis than the brown ore. As a general rule the brown ore carries less than 10 per cent of manganese while the black ore contains about 15 per cent and sometimes as high as 22 per cent of manganese.

Jan 1, 1930

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today's miners and to tomorrow's emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook (Volume III) contains overall injury experience for coal mines, both anthracite and bituminous coal, coke plants, petroleum and natural gas, peat, and asphalt and related bitumens (native); metal mines, metallurgical plants, including ore-dressing plants and primary nonferrous reduction plants and refineries; nonmetal mines; nonmetal mills; sand and gravel operations; slag (iron blast-furnace) plants; and stone quarries and their related plants. Volume I of the yearbook contains a chapter showing injury experience and employment data treated separately by categories: Metal mines, nonmetal mines, quarries and their related plants, metallurgical plants (ore-dressing plants and primary nonferrous reduction plants and refineries are shown separately), nonmetal mills, sand and gravel plants, and iron blast-furnace slag plants. Volume II contains injury and employment experience in the fuel industries (anthracite, bituminous coal including lignite, coke, petroleum and natural gas, native asphalt and related bitumens, and peat). Injury and employment data were collected from coal producers on the regular mandatory basis as required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Similar data for 1962 from metal, nonmetal (except well and brine operations), stone, and sand and gravel producers were collected by a. mandatory reporting system under the provisions of the Act of September 26, 1961, Public Law 87-300 (75 Stat. 649). Before 1962, these nonfuel producers reported voluntarily to the Bureau of Mines. Producers of all other minerals (fuel and nonfuel) reported the requested injury and employment data voluntarily to the Bureau for 1962, the same as in preceding years.

Jan 1, 1963

By R. V. Ramani, P. M. T. White, D. Sutton

3.1 Criteria for Selection A coal deposit has the following major characteristics: i) wide distribution as a flat-lying, thin, bedded deposit ii) stable nature of its major components and ranking characteristics such as carbon, heat content, volatile components, specific gravity, etc. iii) number of constituents and characteristics which under present regulations limit usage, such as content of ash, sulphur, sodium, etc. iv) effect of characteristics of over- and under- lying host rocks including porosity and permeability, lithology and general geology v) low value, high bulk nature. Because of the relative stability of its major components and its low unit price, coal does not require the same attention to detail as do the metal deposits. However, new regulations combined with social pressures make it imperative that more accurate information be made available concerning factors which affect the quality of coal and which may have an adverse effect on the environment when the coal is mined or burnt. The method selected for the evaluation of a coal deposit must, therefore, be flexible and sensitive enough to be used to interpolate stable parameters whose general distribution character-

Jan 1, 1974

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By Gerrit V. R. Goodman, Jeffrey M. Listak, John A. Organiscak

Data on dust control practices, geology, and occupational exposures were gathered for approximately eighty underground continuous mining units. Despite silica contents in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/rn3 on a majority of occupational dust samples while the remainder had difficulty maintaining this level. These two sample sets were termed group A operations and group B operations, respectively. Analyses of productivities, geologies, and dust control parameters revealed only minor differences between these two groups. Subsequent analyses of face ventilation design showed considerable differences in silica exposure and silica content between group A and group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber', This face ventilation system may benefit operations having difficulty controlling silica dust exposure and silica dust content. Finally, the collected data showed that occupational samples from group B operations possessed generally higher silica exposures and silica content than similar samples from group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

By Thomas V. Falkie, R. Venkataramani

Underground coal winning operations can broadly be classified as conventional, continuous, and longwall mining. In conventional mining, the operations of cutting, drilling, blasting, loading and hauling, and roof support are performed in that sequence in each working face in a work area. The major difference between continuous and conventional mining is that the coal is cut and loaded by a continuous miner in the former, thereby combining the unit operations of cutting, drilling, shooting, and loading into one. Longwall applications have been viewed with great interest in recent years, and although at the end of 1970 there were only 37 longwall installations in the U. S. with combined production of less than 4 percent of underground total, there is no question about the growth potential of longwall in the United States. Increased capacity, versatility, and power characterize continuous miners today. Although continuous miners have outsold conventional gathering-arm type loading machines for some years, the latter, in the new extra-high capacity types, are continuing to find wide use. Whether the mining system is continuous or conventional, the haulage units may include six-wheel articulated shuttle cars, tractor-trailer units, or extensible belt and bridge-conveyor systems, all tending to increase the productivity of the face units. The decision as to which to choose - continuous or conventional mining - is complicated, and both systems are capable of high production rates. Most continuous miners in use today have a revolving pick-mounted drum to cut the coal and a gathering arm loading unit. Functionally, there is little difference between the loading unit in a

Sep 1, 1972