Search Documents

By R. B. Tippin

Research investigations conducted on five ore samples show the applicability of heavy liquid separation (HLS) techniques to mineral processing. Under proper operating conditions, semicontinuous tests in small fluid cyclones yielded 90 percent sink-float concentrates with recoveries exceeding 90 percent on minus 35-mesh ore samples of kyanite, potash, spodumene, fluorspar, and beryl. Although none of the ores were examined in detail, their response to this novel concentration method provides basic examples that are typical of the process. Various aspects of cyclone design and operational characteristics of heavy liquid cyclone circuits were studied which demonstrated the flexibility of HLS by using multiple units connected in series. A comparison of two heavy liquid solutions, tetrabromoethane and methylene bromide, exhibited their individual advantages and limitations. Unique problems relative to this process are discussed including liquid viscosity, mineral composition of the ore, toxicity, and material handling hazards.

Jan 1, 1968

By Jalna R. Zatko

The Bureau of Mines has developed and constructed an apparatus that is capable of measuring concentrations of high-molecular-weight polymers in solution at 10 ppm and less. A means for determining low concentrations of polymeric solutions was devised that was independent of slight fluctuations in solvent quality in order to measure polymers in effluent prior to recycling of the recovered solution. The concentrations of polymers ore related to a measured pressure drop observed during turbulent flow of the solution. Low concentrations of polymers of ethylene oxide and acrylamide (frequently used as flocculants for clay waste systems) in aqueous and salt solutions have been successfully measured on the apparatus constructed by the Bureau.

Jan 1, 1981

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By Bradley V. Johnson

The Bureau of Mines constructed a microminer--a scaled-down (5-by 5- by 11-foot) continuous-mining machine of the drum type with a unique triaxially controlled head--for use in a research program to study the effects of continuous-mining-machine parameters on the generation of respirable dust. This report describes field research with the microminer at the Bureau's Experimental Mine at Bruceton, Pa. Experiments were conducted to determine the effects of depth of cut, rotational speed, and sump and shear rates on the generation of respirable dust. The cutting forces were also monitored and compared with depth of cut. There appears to be a reduction in the amount of respirable dust generated when the depth of cut is increased or rotational is speed lowered, Variation of other machine parameters seems to have little effect on dust generation.

Jan 1, 1975

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By M. D. Marshall

This handbook is for the engineer or person responsible for the storage and removal of material from bins and silos in the minerals industry. The objective of the handbook is to prevent bin-related accidents by eliminating problems which require workers to enter bins. It provides basic information on handling materials so that knowledgeable decisions can be made on bin design and accessories to minimize flow stoppages. Materials are classified in terms of their flowability, and bin design and accessories suggested for each classification. A method for classifying a material is also given, and the various types of material flow aids reviewed. Safety around bins is the basic theme of the handbook. Federal regulations are reviewed and additional suggestions presented to prevent bin accidents. New equipment for releasing material hang-ups is reviewed.

Jan 1, 1984

By Joseph L. Condon

High-speed movies were taken of crater experiments in two-dimensional plates of Tennessee marble to study craters being formed primarily by stress-wave action. The contribution of gas action to the cratering process was minimized because the two-dimensional models did not contain the expanding gases from the explosive. Four burdens were studied for solid plates and one burden for a segmented plate. After cratering, the plates were reassembled for dye penetrant studies of fracturing. Flyrock velocities were calculated and related to the degree of fracturing, and compared with those from quarry shots. In general, the smallest burdens produced the highest flyrock velocities and the least amount of fracturing. Flyrock velocities compared favorably with initial flyrock velocities in quarry blasts, but did not show step accelerations due to gas effects as did the quarry blasts. The test with a segmented plate was used to simulate cratering in a jointed material and showed that stress-wave effects can be important for crater formation in jointed rocks.

Jan 1, 1972

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By X. N. Hu, X. Shi, V. Vallyathan, N. S. Dalai

"Although silicosis has been studied extensively, the mechanism is still not fully under stood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are thought to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.INTRODUCTIONSilicosis is a debilitating pulmonary disease that afflicts persons (miners, foundry workers, ceramic workers, heavy construction workers, etc.) who chronically inhale silica-containing dusts (Schepers, 1960; Silicosis and Silicate Disease Committee, 1988). Since silica is second only to oxygen in weight percentage of the earth's crust (about 28%) and is found in an enormous diversity of minerals, it is natural that silicosis is one of the Major industrial health hazards all over the world. Although silicosis has been studied extensively, the mechanism by which the dusts exert their toxic actions on cells and the processes by which these-actions progress to fibrogenesis are still poorly understood. The biological characteristics of the dusts are largely unknown, although it is suggested that the dust size, shape, surface charge, roughness, surface chemical composition, trace metal content, and crystallinity; dose of silica in the ambient air of the workplace; duration of exposure; genetic variation in exposed sub¬jects; personal respiratory patterns; and presence of any coexisting dis¬ease (such as tuberculosis or rheumatoid arthritis) all influence the ex¬pression of silicosis (Koskinen et al., 1983; Noweir et al., 1980; Raask and Schilling, 1980; Reiser and Last, 1979; Thorne et al., 1985; Wolff et al., 1981). The actual biochemical mechanisms through which these factors operate are still unclear. However, the experiments do provide evidence that the actions of certain unique properties of silica surface on the cell membrane are the starting point of the silicotic process (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Marks, 1957; Parazzi et al., 1968; Reiser and Last, 1979; Summerton et al., 1977). This article summarizes literature on chemical properties of silica dusts and how silica dusts are thought to interact with the cell membrane, with emphasis on hydrogen bonding and free-radical interactions."

Jan 1, 1989

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

By Ralph L. Brown

"IntroductionThe accumulation of gummy and resinous deposits in consumers' gas meters began to assume serious proportions about 1917. As the trouble developed and spread in the years following, it manifested itself in several ways, which ultimately began to the expressible in distinctly economic terms, more specifically in terms of costs; in 1922 an organized and fundamentally based investigation of this trouble was begun. In an earlier paper*** a short statement of the occurrence and costs of the deposition was given and at the same time an analysis of the problem, as well as well as a general plan of attack, was presented. That plan included two general phases, first, a chemical study of typical was 1 quarry or 2 cosinous content , mauformly consituents, rmln and selected subjects; and secondly, a comparative survey of plants affected and sufficient therewith, attention being paid to construction, operation, meter conditions and related data. In reporting progress in the axtual investigation, it was definitely set down that the basis of the gummy deposits was the unsaturated hydro consulting from the carburxtion of the water-gas with oil. That the presence of oily-gas condensate was closely associated with and largely"

Jul 1, 1923

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

By Frank A. Peters

This description of process evaluation techniques used by the Bureau of Mines for studying proposed processing techniques has been prepared to provide those interested in using these studies with an understanding of the methodology. The methods used for preparing both capital and operating cost estimates are described. Each step in preparing the evaluations is described. Types of equipment costs are shown and factors used in the estimates are defined. Uses of the estimates are suggested and several examples are included. The accuracy of various types of estimates is discussed, along with an explanation of the reason for selecting the type used in the Bureau's process evaluation studies.

Jan 1, 1987

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By V. Rajaram, S. Bhattacharya, M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, (in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory a field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30% to 65% less in reverse than when operating in the normal forward mode.

Jan 8, 1983

By Kathleen J. D?Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By Mark R. Pettitt

After a long series of laboratory and in-mine tests, a cost- effective, mineworthy, reduced-noise auger miner cutting head was de signed, fabricated, and field-tested by Wyle Laboratories under contract to the Bureau of Mines. Compared with standard auger cutting heads, the new heads reduced noise by 10 dBA at the jacksetter's position and by 6 dBA at the operator's position. This report contains detailed fabrication instructions, including engineering drawings, that show how a standard auger cutting head can be modified to produce a reduced-noise auger.

Jan 1, 1984