Search Documents

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By I. A. Jacobson

In a closely controlled laboratory retorting system for oil shale, a relationship was developed by the Bureau of Mines between the temperature in the retort and the weight ratio of ethylene to ethane in the gases produced. Reciprocal temperature was shown to be directly proportional to the log ([ethylene]/[ethane]). From this relationship a number, called retorting index, was developed. The retorting index has the dimension of temperature, but its magnitude depends on both temperature and residence time for the reactants in the heated zone in the oil-shale retort. The slopes of the lines relating reciprocal temperature and the logarithm of the ethylene-ethane ratios are nearly constant for each of the retorting processes for which data have been presented. The retorting index should be a valuable tool to control the operation of oil-shale retorts, either aboveground or in situ. If an optimum operating condition can be established, the maintenance of the optimum or the departure from it should be easily monitored by use of the index.

Jan 1, 1974

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau's long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By James R. Aggson

This Bureau of Mines report presents a finite element analysis of roof stresses associated with a 4-foot-high by 18-foot-wide underground coal mine entry. This analysis starts with known loading conditions determined in an underground coal mine in West Virginia and is extended to other possible underground loading conditions. The roof failures predicted by the finite element analysis under known loading conditions correlate well with the roof failures observed underground. The most probable failure modes are identified for the various loading conditions considered. Various failure preventive measures are discussed.

Jan 1, 1979

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By George R. Schottler

The Bureau of Mines investigated the distribution of uranium and various methods of ore sampling in a uranium deposit typical of those in the Morrison Formation sandstone of the Ambrosia Lake area, Grants mining district, north-western New Mexico. Chemical and radiometric assays of diamond-drill core samples are compared in detail by statistical techniques, and the assay data are correlated with the stratigraphy of the deposit. Conclusions applicable to ore-reserve estimation in geologically similar uranium deposits are drawn.

Jan 1, 1971

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By John Nagy

Results of initial research by the Bureau of Mines are given on the dust explosion hazard of float coal and on the related factors of occurrence, rate of production, sampling techniques, transport, and deposition of float coal. Tentatively, it is suggested that where float coal deposits prevail, a mini-mum of 80 percent incombustible be maintained in the top 1/8-inch layer to neutralize the explosion hazard of the surficial coal deposit.

Jan 1, 1965

By John O. Atkins

[Experiments were conducted by the Bureau of Mines on five types of simuated lunar rock (dacite, tholeiitic basalt, vesicular basalt, pumice, and uluth Gabbro) to study the effects of various simulated lunar environments n their strength and deformational properties. Specimens were tested in an ltrahigh vacuum (UHV) system at pressures ranging from atmospheric down to 0-11 torr and at temperatures of -130°, 20°, and 135° C. All tests were onducted with a servocontrolled testing machine. Rock specimens tested at 0° C in UHV exhibited significantly higher compressive strength and Young's odulus than those tested at 20° C in atmospheric pressure. The magnitudes f increase are related to the porosities and permeabilities of the rock pecimens; high porosity and permeability allow better outgassing and thus nprove surface cleanliness in UHV. The compressive strength generally ncreases but Young's modulus decreases as test environments change from 20° C i UHV to 135° C in UHV. No significant difference was observed in the iysical properties measured at 20° C in LTV and -130° C in UHV. Anisotropy i strength and Young's modulus exist both in UHV and at atmospheric condi¬'.ons with the same symmetry pattern. The orientations of the principal axes iy, however, change from the atmospheric to UHV condition. The results idicate that rock fragmentation in lunar environment will require more ergy than that at 20° C in atomospheric pressure.]

Jan 1, 1974

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By O. C. Blade, Elizabeth Hughes

Conservation in the utilization of any product is always subject to improvement if the composition and properties of the product are known. Petroleum is no exception, and knowledge of the characteristics of crude oils, even when given on the broad basis of routine type analyses has proved useful to chemists, engineers, and geologists in improving pro- duction and utilization of petroleum. For a quarter of a century the Bureau of Mines has sought to provide such information regarding crude oils and has analyzed many samples of petroleum by its standardized rou- tine method. Most of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published up to January 1, 1948. The routine method used for all these analyses is basically the same as that described by Dean, et al.. Briefly, the procedure consists of testing by standard methods, small samples of a crude oil for gravity, sulfur, color, and viscosity, and of distilling a sample of the crude oil by a standardized procedure and determining certain properties in the sep- arated fractions and residuum. Careful records are made during the proce- dure, and the distillation data obtained are used to calculate the approx- imate amounts of products present in the sample such as percents of gas- oline, kerosine, gas oil, and lubricants. The data obtained are recorded on a standard analytical report form. An analysis of a sample of typical midcontinent crude oil is shown in table 1. Compilation of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses are often shown in connection with other studies, such as engineering field reports. This bibliography is a compilation of references to 115 publications, which contain analyses of crude oils by the Bureau of Mines. References may be found to analyses of crude oils from the United States, Canada,

Jun 1, 1948

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920

By L. A. Haas

The degree of reduction of various silica-graphite mixtures was studied in a batch reactor to determine optimum physical conditions for maximizing the carbothermic reduction of silica. The extent of interaction was determined for reactant mixtures in loose powder and briquet forms at pressures less than 0.01 torr and temperatures up to 1,445° C. Molar ratios were varied from 0.05 to 6.5 with maximum reaction at a ratio of about 1.5. The solid-solid reaction did not appear to involve gaseous intermediates. The extent of reaction better correlated with the number of interparticle contacts than with the true surface area of the reactants. Carbonized dextrose was a better reductant than graphite.

Jan 1, 1968

By Martin Berman

The Bureau of Mines has investigated the mineral matter content of 38 American coals using X-ray fluorescence. Measurements of the Ka intensity for magnesium, aluminum, silicon, sulfur, calcium, and iron permit the determination of those elements as well as an indirect determination of the ash con-tent of the coals. The percentage of each of the six elements was corrected for absorption by all six elements as well as by hydrogen, carbon, nitrogen, and oxygen. It made little difference whether the values used for hydrogen, carbon, and nitrogen were obtained from chemical analysis or whether average values for all coals were used. In all cases, oxygen was obtained by difference. The correction for absorption by all these elements involved the inversion of a 6 X 6 matrix and was performed by computer. Assuming that the elements magnesium, aluminum, silicon, calcium, and iron were present in the ash as oxides, the quantity of ash was determined. The results for the mineral elements as well as for ash and oxygen were in good agreement with chemical results. Particle size was found to have a significant effect on fluorescence intensities. A study of size effects was made for pyrite particles, since the sulfur content of coals is of particular interest. Theoretical equations were derived and verified relating the intensity to particle size. It was found that the coal samples must be ground to less than 2 microns. Sulfur appears in several forms in coal, and the effect of sulfur form on intensity was investigated. It was found that the Ka intensity was independent of sulfur form but the Kß intensity varied with the type of sulfur. Thus, the Ka intensity was used for determination of the quantity of sulfur present. Utilization of the sulfur KB intensity did not permit a determination of the proportions of sulfur forms present in coal. However, for synthetic mixtures of cystine and pyrite in carbon black, measurement of sulfur Ka and Kß permit determination of each constituents from measurements of sulfur intensities alone.

Jan 1, 1968

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950