Search Documents

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By R. V. Lundquist

The specific conductance of solutions of sodium hydroxide and of sodium aluminate was directly proportional to the temperature. The specific conductance of sodium aluminate solutions with identical sodium ion concentration and at constant temperature decreased with increase in aluminum concentration. The aluminate ion population in solution was shown to consist of a mixture of monovalent and polyvalent ions. Aluminate ions did not influence the temperature dependence of pH in caustic solutions containing sodium aluminate. The density and viscosity of a solution was inversely proportional to the temperature and directly proportional to the concentrations of sodium and aluminate ions.

Jan 1, 1965

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Roy L. Wilfong

Surface area measurements were conducted on cadmium sulfide powders following thermal treatments at temperatures up to 500° C and treatment times up to 1 week. Thermal treatments at temperatures up to 300° C produced no significant changes in the surface area of the powders even after 1 week of exposure. At 500° C some decomposition of the cadmium sulfide occurred.

Jan 1, 1970

Lower the respirable dust expo? sure of longwall shearer operators Approach Use improved water sprays on the shearer machine to direct the dusty air toward the face. In laboratory tests and actual mining conditions, the shearer-clearer has proved to be an effective dust control technique. Recent field experience however, has indicated that not enough technical information is available on proper installation of the improved shearer-clearer. This Technology News will provide details of the Improvements made to the shearer-clearer and provide guidelines for installing the system. How It Works The shearer-clearer system consists of several strategically-mounted water sprays and one or more passive barriers. The sprays redirect the airflow around the shearer into both a clean and a contaminated split. The sprays confine the contaminated split or dust cloud to the coal face, allowing the shearer operators to remain in the clean split on the walkway

Jan 1, 1986

By R. L. Wise

Heat content studies were conducted on burned shale, spent shale, and three grades of raw oil shale from the Green River Formation. Corrections were made for product enthalpies. The results were compared with previous work, indicating good agreement below retorting temperatures, but some differences at retorting temperatures. A general equation was developed relating heat content to oil-shale grade and temperature.

Jan 1, 1971

By W. M. Merritts, Charles Findlay, Stephen Krickovic

Methane emission rates were studied in a Pittsburgh coalbed mine in northern West Virginia. A fullface boring-type continuous miner, equipped with a methane monitor, was used in the development of a set of eight main headings, one side of which was near old workings; the other side abutted virgin coal. Two air splits ventilated the section. Air volumes and methane percentages were recorded, and time studies of the miner were made during five consecutive operating days, during which a complete cycle of mining the headings and one line of related breakthroughs was accomplished. Methane emission rates increased significantly as mining progressed from the side near old mine workings toward the virgin area, and generally increased with coal extract ion. Mining in the heading immediately adjacent to virgin coal was interrupted quite frequently, owing to excessive methane concentrations at the face, despite adequate air volumes and acceptable methane concentrations in the immediate return airway.

Aug 1, 1970

By Fred N. Kissell, Jon C. Volkwein

In This Chapter [How inert gas works to prevent methane explosions How inert gas is generated and delivered at highwall mines Volume and quality requirements for inert gas at highwall mines How an inert gas system is operated and Precautions to take during mining to prevent methane explosions] This chapter discusses a method, originally developed by Volkwein and Ulery [1993], to prevent methane explosions during highwall mining. In highwall mining, a horizontal auger or a mining machine enters the coal seam from a surface mine pit at the bottom of a highwall, and the coal is mined out from a series of parallel holes. Explosions can be prevented by injecting inert gas into each hole as it is mined. Coal near the surface has lost most of its methane gas over time. However, in recent years, surface mining has been used for deeper reserves of coal. This trend toward mining deeper reserves has increased the chance of encountering methane, and methane explosions at highwall mining operations have resulted in injuries. HOW INERT GAS WORKS TO PREVENT METHANE EXPLOSIONS A methane explosion requires the presence of sufficient amounts of both methane and oxygen, as well as an ignition source. If the methane cannot be reduced and the ignition source cannot be eliminated, then explosions may be prevented by adding an inert gas, which contains little to no oxygen, to the mixture [FWQA 1970]. Just how much inert gas must be added depends on the mining rate, as well as the composition of the inert gas. An explosibility diagram can be used to show whether a methane mixture is explosive after inert gas is added [Zabetakis et al. 1959] (Figure 10–1). This diagram indicates that gas mixtures fall into one of three range categories—explosive, explosive when mixed with air, and nonexplosive—depending on the percentage of methane and percentage of “effective inert.” Effective inert is calculated from the percentage of “excess nitrogen”3 and percentage of carbon dioxide in the mixture.

Jan 6, 2006

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

By James L. Konchesky

Crushed coal, consisting of a wide range of sizes, was effectively blended by recycling it through a bin equipped with a particle distributor. Vertical blending was accomplished by simply recycling the coal; it was not significantly influenced by the horizontal blending that was achieved by the distributor. The method was effective, even though the coal was wet and possessed poor flowing characteristics. Recirculation appears capable of providing uniform blends of solids that can be more efficiently processed. Recirculation also appears useful, preceding packaging operations, to insure for blending of solids into specification products. Continuous measurement of the bulk density of the coal by a gamma ray meter proved to be an effective monitor of vertical blending effectiveness.

Jan 1, 1972

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By S. H. Katz

Tar and suspended matters are removed from manufactured gas used for domestic and industrial purpose.

Jul 1, 1922

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978

Use water-jet-assisted cut-ting technology to reduce the exposure of mi ne workers' to respirable dust. Approach Install water-jet-assist on mining machines and evaluate its impact on respirable dust. How It Works Water-jet-assisted cutting involves a mechanical cutting bit working in combination with a moderate pressure (generally up to 10,000 psi) water jet directed just in front of, or through, the bit tip. One of its advantages is reduced dust generation because the jet wets the face of the material being cut more efficiently than a conventional low-pressure water spray, thus capturing much of the dust before it ever becomes airborne. It also removes loose cuttings ahead of the bit before they are pulverized by the bit into respirable dust. Total water consumption is about the same as for conventional low pressure dust control water spray systems. However, there is some increase in power consumption because of the energy needed to provide the high pressure water.

Jan 1, 1987

By Christopher C. Jobes, N. Kumar Kittusamy, Alan G. Mayton, Dean H. Ambrose

Researchers with the National Institute for Occupational Safety and Health (NIOSH) conducted a systematic study to evaluate seat designs on low- and mid-coal-seam shuttle cars. The purpose was to gather additional data to support earlier findings that NIOSH seats, with unique viscoelastic foam padding, are indeed improved designs for coal mine shuttle cars. This study included a larger sample of shuttle car operators than a prior NIOSH investigation. Eight shuttle car operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers then compared the operators’ perceptions with field-measured levels of vehicle jarring/jolting. Seven seat designs were evaluated on low- and mid-coal-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. These seat designs comprised the one already in use on each vehicle and five NIOSH designs. Experimental data were collected using accelerometers, signal conditioning amplifiers, and filters connected to a data recorder, whereas subjective data were gathered via a visual analog scale (VAS) and a questionnaire. Field trials included shuttle cars operating under full- and no-load conditions. VAS responses indicated that NIOSH-designed seats performed better relative to comfort and isolation from vehicle jarring/jolting than the existing seats used in the shuttle cars. Both mid- and low-coal-seam shuttle car operators, during no-load and full-load conditions, rated lower levels of jarring/jolting with the NIOSH seat design. Questionnaire responses indicated that shuttle car operators rated NIOSH seat designs as more comfortable. Vehicle operators most frequently suggested the addition of armrests as a way to improve the seats on the mid-seam shuttle car. The quantitative levels of vehicle jarring/jolting for the no-load condition (more severe condition for vehicle operation) showed that NIOSH seats for the mid-coal-seam shuttle car performed better than the existing seat in terms of peak acceleration and crest factor. Similarly, for the low-coal-seam shuttle car, NIOSH seats performed better than the existing seat in terms of peak acceleration, root-mean-square (RMS) acceleration, and crest factor.

Jan 11, 2006