Search Documents

By D. A. Stanley

The Bureau of Mines has developed a simple titration technique for determining the points of zero charge (PZC) on minerals. The technique consists of titrating a mineral slurry with the potassium salt of polyvinyl sulfuric acid (PVSK) in the presence of an indicatory dye and a positively charged polymer. Values obtained by this simple method are in good agreement with values found in the literature.

Jan 1, 1982

By L. C. IlsLey, E. J. Gleim

It is the firm belief of the Bureau's engineers that the introduction of electrical mining machines has done much to increase safety in mining as a whole . There can be no doubt but that the substitution of machine mining together with permissible powder for the method of " shooting from the solid " has been the means of saving the lives of many shot- firers . Machine mining also leaves the roof in a better condition as lighter charges of powder are required to bring down the coal . Thus the danger from falls of roof are lessened . It is recognized that every effort should be made to prevent all accidents due to the use of electrical machinery but it is felt that any action tending to limit the use of such machinery would be a backward rather than a forward step in the safety measures laid out to decrease the hazards in coal mining .

May 1, 1920

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

By W. M. Dressel

A simple field test for detecting the presence of germanium in rocks, coals, and flue dust has been developed by the Bureau of Mines. The method consists of dissolving germanium from the samples by either acid or fusion treatment methods, adding a few drops of hematein or phenylfluorone dye, and extracting the resulting colored complex with carbon tetrachloride. INTRODUCTION Germanium is obtained commercially as a byproduct of zinc production, as a coproduct of base-metal refining from germanium-bearing mineral, and as a recovered product from the ash of some coals. The growing use of germanium in the electronics industry has increased demand for this semiconducting metal to the extent that an intensive search for new sources of supply is necessary.

Jan 1, 1962

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

By R. M. Santmyers

This paper represents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining legislation of Tunisia was prepared from a copy ( in French ) of the Mining Decree of Tunisia promulgated December 29 , 1913 , by the Resident General of France in Tunisia and effective January 1 , 1914. It is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it will be referred through the courtesy of the Department of State .

Mar 1, 1933

By J. G. Kirby, F. S. LOTT

The mmber of petroleum refineries in the United States decreased during 1949 from 375 to 367 while the total crude-oil charging capacity of refineries continued to increase. A gain in the through-put capacity of 257,305 barrels daily raised the total to a new high level 6,696,300 as of January 1, 1950. The capacity of the average refinery to process crude-oil increased during 1949 from 17,171 barrels daily to 18,246. The four coastal refinery districts accounted for 178,900 barrels or 70 percent of the total capacity increase and the Illinois-Indiana- Kentucky district 57,950 barrels, or 23 percent. Slight declines in capacity were reported in the Texas Inland and the Arkansas-Louisiana Inland districts. The capacity building on January 1, 1950, 145,600 barrels daily, was less than half the amount under construction a year earlier. Most of the new construction involved enlargement of existing refineries and was confined to the East Coast and Indiana-Illinois-Kentucky districts. Two new refineries, however, were under construction, one in Oklahoma and the other in Texas. The shut-down capacity increased for the first time since 1946, and the 473,302 barrels daily reported on January 1, 1950, was the largest recorded since January 1, 1938. The only refining district showing a decline in the shut-down capacity was the Appalachian No. 2 district. The largest increases were reported in the Texas Gulf, Indiana-Illinois- Kentucky, California, and East Coast districts. The operating ratio of the petroleum refining industry, as indicated by dividing the January 1950 runs to stills of 5,483,000 barrels daily by the total installed capacity January 1, 1950, was 81.9 percent, compared with a ratio of 87.8 percent at the beginning of 1949.

Aug 1, 1950

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

Develop new technology to encourage domestic processing of automobile catalytic converters for recovering platinum -group metals. Background Automobile catalytic converters are used to convert pollutants in automobile exhaust into water vapor, carbon dioxide, and nitrogen, About 1 million troy ounces of platinum-group metals arc used each year in the. United Slates to manufacture catalytic converters. It has been estimated that about 60 pct of the used catalytic converters arc being collected. Most of these used catalytic converters were not processed in the United States but were exported to Japan or Europe for processing. In 1991, about 250,000 troy ounces of platinum-group metals were recovered from scrap catalytic converters collected in the United States. Each short ton of decanned catalyst may contain 30 troy ounces of platinum-group metals valued at over $15,000. Development of an economic process for the recovery of platinum-group metals that can be operated on a small or large scale may increase, the percentage of catalytic converters collected and encourage domestic processing to recover a platinum-group metal concentrate. This would significantly decrease the dependence of the United States on imports for these critical and strategic metals.

Jan 1, 1992

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By F. B. Tough

An inusual job in controlling a gas well was executed on No. 1 well, Inland Oil and Refining Co., situated on the Alkali Butte structure, Freemont County, Wyoming. The work was done by the company in cooperation with the . S. Bureau of Minos, and resulted in a fuel saving of $5,000 in one season and of a repair job estimated at $15,000, or a total of $21,000. The woll had an open flow of 6,000,000 cubic feet of gas per day with a rock pressure of 560 pounds per square inch. A string of 6-1/4 inch casing with a toothed shoe was set on the cap rock above the gas sand at 2181 feet. Then the well was shut in, the gas worked out around both the 6-1/4 inch and 6-1/4 inch strings, breaking through the ground surface at several points under the derrick. Casing troubles encountered while drilling made it unsafe to attempt Coving the 6-1/4 inch string. Moreover, it was important from the standpoint of good management to make the gas from this well immediately available for fuel in other operations and, in addition, to save the gas from wasting. An ordinary mudding and cementing job would have necessitated sitting down this well for probably two months out of a very short operating season. For these rousons it was determined to mud the well, if possible, between the 6 and 8 inch strings by pumping mud fluid through the connection from the gas clamps. The gas clamps used wore of ordinary construction with a side outlet, making them equivalent to a Braden-hoad. When the mud fluid was pumped through the gas clamp into the space between the two strings, it began to appear inside the 6-1/4 inch string. It apparently entered the well either around the toothed shoe or through a "line sawed" leak in the string and was blown out of the well as fast as it was pumped in. In order to stop the leaks, about a half a gunny sack of finely chopped bull ropa was fed with the mud between the casings as before. The hemp gathered around the valves of the mud pump to some extent, and it also stuck in the casing-head fittings a few times. An obstruction in the casing- head would be removed by permitting the woll to "blow back" for a few seconds, and one in the pump valves, by removing the valves when necessary. In two days' time sufficient hemp and mud had been pumped into these strings to kill external and internal pressure. The wall was shut in and allowed to stand over night. The next day, by opening and closing the master gate at intervals,

Mar 1, 1921

Measure the daily exposure of individual miners to alpha particles emitted by radon daughters (radioactive decay products of the radon gas present in the mine atmosphere). Approach A dosimeter worn by a miner counts alpha particle emissions from radon daughters, RaA (Polonium 218) and RaC (Polonium 214), collected on a filter, and stores the gross count for later readout. How It Works A pump draws air into the detector assembly where radon daughters are collected on a filter. The detector, a solid state surface barrier type, is mounted in the filter head behind a thin mylar disc which serves as a moisture barrier. When a radon daughter decays and its alpha emission strikes the detector, the alpha particle causes a pulse of electrical charge in the detector. The circuits used to condition and count the electrical pulses generated in the detector are represented by the other blocks shown in the simplified block diagram. Each pulse is first amplified.

Jan 1, 1979

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By Lloyd A. Morley, Alan M. Christman

This report was prepared by the Department of Mineral Engineering, The Pennsylvania State University, University Park, Pennsylvania under USBM Grant Number G0155102. The grant was initiated under the Metal and Nonmetal Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. Roger L. King acting as the Technical Project Officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period February 1, 1975 to July 31, 1976. This report was submitted by the authors on August 31, 1976.

Jan 1, 1976

By Raja V. Rarnani, Robert L. Frantz

"Scientific, engineering, and biomedical research teams synergystically developed major topical research areas in the Respirable Dust Center. Descriptions of their interactions and resulting accomplishments demonstrate how cooperative research within and among these study groups benefits the overall respirable dust research and practical application needs of the mineral industries.The development of a state-of-the-art small animal inhalation exposure facility suitable for studies of fresh and aged coal mine dust, a major goal of this research group, will contribute toward the GTCRD goal of advancing the understanding of causative mechanisms for the occupation-related lung impairments and the airway diseases of mine and mill workers. Such understanding includes improved definition of the role of various aspects of the lung environment (e.g., surfactant and the mucociliary system) in the disposition and toxicity of respirable dust, comprehensive characterization of the role of the pulmonary alveolar macrophage (PAM) and its secretory products on the development of dust-related lung disorders, and an expanded search for methods to reduce the toxicity of respirable dust both before and after it enters the lung. The National Academy of Sciences has recommended, in Measurement and Control of Respirable Dust in Mines, that respirable dust research should include study of the behavioral and constitutional factors affecting individual susceptibility to workers' pneumoconiosis occupational disease and the development of methods for detecting the potential onset of pneumoconiosis earlier and more conclusively than can be done using X-ray methods. These recommendations have guided the research group in its goals of establishing and disseminating a scientific protocol for standardizing the inhalation testing for all research objectives within the Generic Center which involve small animal exposures and implementing the infrastructure necessary to make lung tissues obtained during inhalation studies available to all researchers within the Generic Center."

Jan 1, 1995

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

By M. MacLaughlin, J. Whyatt

A case study is presented that relates statistical descriptions of joint sets to the distribution of local wedge failures along the crest of a catch bench at the Yellowstone Talc Mine. The fracture sets and bench width were mapped by teams of geological engineering students from Montana Tech under the direction of Dr. Mary MacLaughlin. The students analyzed the fracture data, conducted physical property tests, and used a beta version of a NIOSH program “Bwedge” to predict the distribution of surviving bench widths. In the course of this analysis the students developed evidence of software performance issues that, unfortunately, frustrated their analysis. These have now been addressed and a full analysis completed. The analysis confirms the validity of the student mapping program and provides insight into the effects of blasting and excavation practices on the bench. It also provides a tool for exploring the pattern of bench crest failure that would result from variations in both bench geometry and blasting practices.