Search Documents

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By W. C. Wahl, M. M. Fine

Leonardite , a naturally occurring , partially oxidized form of lignite with a high content of humic acids , was investigated as a binder for iron ore pellets . Although insoluble in original condition , leonardite forms watersoluble salts with good binding properties when treated with certain alkalis such as sodium hydroxide . Soluble leonardite imparts excellent dry strength to pellets , but green strength is somewhat lower than that obtainable with bentonite . However , green strength can be improved by adding a small amount of calcium hydroxide to the leonardite - concentrate mixture . Leonardite binders were used successfully on three of the four different concentrates tested .

Jan 1, 1964

Mine closing methods should be carefully considered. If not properly sealed, an abandoned mine may continue to produce acid water. Since 60 to 90 percent of the total acid discharged from all coal mines is from abandoned mines,(58) some states require that provisions for sealing be contained in the mining permit application. Closing an operation to prevent harmful mine drainage into nearby runs and streams is a subject of much concern to states as a result of continuing problems from long abandoned mines which were improperly closed.

Jan 1, 1970

By K. E. Tame

As part of a Bureau of Mines survey of radioactive waste disposal , a laboratory investigation was made to study such problems in carbonate leaching mills . Because uranium concentrators employing carbonate leaching with caustic precipitation normally recycle barren solutions to the washing circuit , the disposal of liquid radioactive wastes is automatically controlled . However , it was deemed important to determine the actual radium 226 concentrations occurring in this type of milling so that the survey of the entire industry would be complete . The laboratory procedure consisted of leaching the ground ore at 85 ° to 90 ° C and 50 pct solids for 6 hours in a sodium carbonate - sodium bicarbonate solution . The pulp was filtered to obtain a pregnant solution that was reacted with sodium hydroxide to precipitate the uranium as sodium diuranate . Regeneration of the barren solution was accomplished by gassing with carbon dioxide . The solution then was reused by advancing the solution through the washing to the leaching operations . The radioactivity in the pregnant solution was unusually high , averaging 6,500 disintegrations per minute ( dpm ) of radium 226 per liter . However , over 95 pct of the radium was precipitated with the uranium . Consequently , no buildup of radium occurred upon reuse of the barren solutions for washing .

Jan 1, 1964

By L. C. IlsLey

As part of its work for the improvement of safety conditions in mines , the Bureau of Mines has undertaken to establish a list of permissible storage - battery locomotives for use in gaseous mines , and , to this end , has issued Schedule 15 , "Procedure for Establishing a List of Permissible Storage -Battery Locomotives for Use in Gaseous Mines . " Up to the present time , two approvals * have been issued under this Schedule , and considerable testing work done on four other applications which have been made for approval . Prior to the publication of Schedule 15 , the Bureau conducted both field and laboratory investigations to determine the hazard from the batteries used in mine locomotives . ** These investigations indicated that the safety of the locomotive would depend largely on proper care of the battery , also on the use of a battery as mechanically rugged as possible . For this reason the Bureau staff , in testing locomotives submitted for approval , considered it advisable to subject the batteries to a jarring or bumping test to prove their adequacy as regards mechanical endurance and ruggedness . These tests on the batteries of the locomotives are described below.

May 1, 1922

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

To develop a safety training module for surface miners and road construction workers exposed to the hazards of highwalls. Background Investigators collaborated to develop a new training module that would address the hazards of working around highwalls. Such a module would be applicable to surface mines and road construction sites, both of which require personnel to work under and on top of steep and often unstable slopes.

Aug 1, 2004

By BUREAU OF MINES

The Bureau of Mines in its investigations of respiratory apparatus for use in mines and allied industries, tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum require- ments for safety in use. Approval certificates are issued for apparatus that meets the bureau's specifications, and the memfacturer is permitted to mark his equipment with a seal showing that it has been approved as "Permissible." A complete list of permissible self-contained oxygen breathing apparatus, gas masks, and hose masks tested before July 1, 1930, was published in Bureau of Mines Information Circular 6362.1 The present list includes all equipment tested and approved up to and including April 1, 1931.

Sep 1, 1931

The Bureau of Mines believes that all coal mines are potentially gassy; for the purpose of administration in the prevention of explosions and fires, the Bureau recommends: That any coal mine wherein methane or other combustible gas can be detected in amounts as much as 0.27 of 1 percent or more by frequent systematic searches shall be classified as a gassy mine. Permissible methane-indicating detectors such as are given in I.C. 7110 or subsequent lists of Bureau approved methane-indicating detectors, or conventional methods of sampling and analysis of required accuracy may be used. The concentration referred to in the decision is percent by volume.

Jan 1, 1941

Wires leading to or from underground facilities can develop hazardous voltages because of lightning exposure. The locations of many mine portals are particularly susceptible to lightning effects. The application of protective devices to limit this potential danger is necessary.

Jan 1, 1975

By Joseph A. DeCarlo

This information circular presents data for 1960 on individual coke plants in the United States. All oven-coke plants in existence, whether active or idle at the close of the year, are listed in this report. With two exceptions, only beehive plants on which reports were submitted to the Bureau of Mines are included. Although the Bureau was unable to obtain reports from these two active plants in 1960, the number of ovens and annual coke capacity are estimates, based on previous reports filed with the Bureau of Mines. Accordingly, there were 73 oven-coke plants in existence at the end of 1960 of which 70 were active. Reports were received on 44 beehive plants of which only 13 were in operation at year end. Oven-coke plants are listed alphabetically by States in table 1 which shows the name and address of the company, location of plant, classification or type of ownership, number and type of ovens, annual coke capacity, and coal-chemical materials produced. The terms "furnace" and "merchant" plants used in this and all other reports of the Bureau of Mines designate the type of ownership. Furnace plants are those owned by iron and steel companies whose main business is production of coke for use in their own blast furnaces. Merchant plants are those associated with chemical companies, gas utilities, as well as those that produce for sale on the open market metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials. The annual coke capacity shown for each plant in this table is based on the minimum coking time necessary to produce coke with qualities suitable for its intended use. Therefore, the annual capacity of a plant may change from year to year, depending on age and condition of ovens, the character and quality of coal carbonized, the grade of coke required, and other factors. For example, annual coke capacity of a coke plant primarily making foundry coke with longer coking cycles would be lower than one making blast-furnace coke. Also some ovens must be operated at slightly lower than normal flue temperature because of the condition of the refractories and maximum capacity would be somewhat lower than designed capacity. For this reason, the capacity reported to the Bureau of Mines may differ from the designed or rated capacity estimated by the coke-oven builders at the time of construction. For example, if the generally accepted standard coking rate of one inch per hour were used on all ovens to calculate total annual capacity, it would have been 80.4 million tons or 2 percent higher than the capacity reported to the Bureau. Because of the factors mentioned above, the annual coke capacity shown in this table is believed to be a reliable measure of the practical operating capacity of the industry.

Jan 1, 1961

By Jon C. Volkwein

The industrial sand industry has been exploring new techniques to reduce dust. One company was experimenting with adding water during bagging operations to the surface of the hag, and into the product as it flowed into the bag. The Bureau of Mines, using instantaneous dust sampling instruments, measured the effectiveness of three methods of adding water. Results indicated that various types of water sprays applied in carefully controlled amounts could reduce dust up to 50% at worker locations at the bagging machine and inside a railroad boxcar. This report also discusses constraints such as product handling, customer acceptance, cold weather problems, dust collector performance, and other areas.

Jan 1, 1981

By John W. Frey

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Persia has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it is being referred through the courtesy of the Department of State .

Nov 1, 1929

By Kenneth J. Miller

Laboratory batch flotation tests were conducted to determine the viability of the Bureau of Mines coal-pyrite flotation process in desulfurizing various coals from the midwestern coalfields. Nine coals obtained from western Kentucky and Illinois were used in the study. In addition to the Bureau's coal-pyrite flotation process, some of the coals were subjected to two-stage rougher-cleaner coal flotation for comparison. The results of this work showed that up to a 70-percent pyritic sulfur reduction could be obtained by flotation and that the Bureau's coal-pyrite flotation was superior to rougher-cleaner coal flotation. Because many of the coals retained far too much sulfur even after second-stage flotation treatment, it was concluded that these midwestern coals are more difficult to desulfurize by flotation than are the Appalachian coals tested in earlier Bureau experiments.

Jan 1, 1978

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

Information is presented on remote sealing of a mine passageway through a borehole by five methods : PPnneeuummaattiicc injection of mineral wool and sand, ureaformaldehyde foam , balloons , urethane foam, and caving by blasting . An adaptation of the method using pneumatically conveyed mineral wool was tried in an operating mine . Further research is needed to simplify and to improve the techniques involved , as well as to explore the possibilities of other methods and combinations .

Jan 1, 1964

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By R. V. Ramani

"In Part 1 of this paper, published in the August 1995 issue of Natural Resources Forum, a review of several mining disasters around the world established the complex nature of their causation and their catastrophic effects. The involvement of human beings, either through acts of commission or omission, was highlighted. In Part 2, a discussion of the various approaches to disaster control, mostly as practised in the USA, is presented. A systems approach to disaster prevention incorporating elements of hazard identification, mine design, emergency response and post-emergency audit is presented.In the USA the role of government in the affairs of its citizens is continually growing. This role is intended to ensure an unimpeded pursuit of happiness and prosperity by the population and to curtail actions which are restrictive or harmful to the citizenry. The passage of a legislation is an indication that it has been decided through the established process that the activities covered by the legislation should receive appropriate consideration. The enactment of the Coal Mine Health and Safety Act of 1969 (The 1969 Coal Act), the Mine Safety and Health Amendment Act of 1977 (The 1977 Mine Act) and the Surface Mining Control and Reclamation Act of 1977 (The 1977 Surface Mining Act), was specifically intended to further the role of government in the health, safety and environmental affairs of the mineral industry.Currently, the federal government's responsibilities for mine safety and health are divided among three agencies: the Mine Safety and Health Administration (MSHA) in the US Department of Labor, the Bureau of Mines (USBM) in the US Department of the Interior and the National Institute for Occupational Safety and Health (NIOSH) in the Department of Health and Human Services (National Research Council, 1981). MSHA is responsible for issuing and enforcing mine safety and health regulations, for training miners and for responding to mine emergencies. The Bureau of Mines is responsible for conducting research on mine safety and on the technological means for reducing health and safety hazards in mines. NIOSH conducts research relating to miner health, and together with MSHA, tests and certifies devices used to detect hazardous materials in mines and protective equipment used by miners. NIOSH also plays a public health role in that its activities in mining include health hazard evalua¬tions, general mining surveillance as mandated by law and medical surveillance including coal miner X-ray and autopsy programmes. MSHA shares with the Bureau of Mines the responsibility for integrating R&D results into operational practice. MSHA implements R&D results either by incorporating them into its own operations or by rule making that requires new practices or equipment to be adopted by the mining industry. In many instances, the Bureau's R&D results have been adopted by the mining industry without rule making."

Dec 1, 1996

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934