Search Documents

By M. U. Ozbay, D. R. Lougher

An in-situ experimental programme was carried out to improve the understanding of the rockmass and pillar behaviour in moderately deep hard-rock mines. The experiments were carried out at Impala Platinum mines and consisted of precise levelling measurements in the footwall of the reef, stress measurements in pillars, convergence measurements in the stope, and petroscope observations in pillars. The results were analyzed using a computer program in an attempt to quantify the characteristic behaviour of the rockmass as well as the pillars. The measured off-reef displacement data were found to co11fonn to the trends obtained from elastic modelling and the correlation could be improved by modelling the small pillars with reduced modulus to simulate yielding' of the pillars. The stress strain curve obtained from analyzing the in situ results, showed that a 6x 3 xl m pillar yields without significant load shedding at peak stress levels of approximately 208 MPa. The closure measurements confirmed that the mechanism of yielding is mainly that of pillars punching into the foundations. Slight to moderate sidewall fracturing and slabbing might be contributing to yielding, but to a much lesser degree than the former mechanism, as the petroscope observation revealed the existence of an intact region beyond 0,6m from the pillar sides.

Jan 1, 1995

The value of incentive payments in the mining industry by K. SMITH, A.R.S.M., B.Sc. (London) (Member) This paper reviews the history of incentive payments in the mining industry, and gives some indication of the magnitude of improvement that has been achieved by this means in the past. The objective is to promote a more general belief in the efficacy of these methods, and thus to encourage their wider and more effective application by mining engineers in general, and by the rising generation in particular. It is concluded, from a consideration of current productivity levels in the gold-mining industry (still South Africa's leading revenue earner), that further substantial improvement can be achieved by a better understanding of the time-tested principles of incentive payments.

Jan 5, 1974

Fathi Habashi, Chalcopyrite. Its chemistry and metallurgy. New York, McGraw-Hill, 1978. 165 pp. RI9,95. Loss prevention and safety promotion The Proceedings of the 2nd International Symposium on Loss Prevention and Safety Promotion in the Process Industries, Heidelberg, 6th to 9th September, 1977, are now available. Chemical reaction engineering The Proceedings of the 4th International/6th European Symposium on Chemical Reaction Engineering (4th ISCRE) held at Heidelberg, Federal Republic of Ge rmany, from 6th to 8th April, 1976, are available from DECHEMA Deutsche Gesellschaft fur Chemisches Apparatewesen, P.O.B. 970146, D-6000 Frankfurt/ Main, West Germany, at the price of DMlOO plus postage and packing. Books received The Institution of Mechanical Engineers Proceedings Volume 190. Tribos abstracts on friction lubrication wear. Published by BHRA Fluid Engineering, Cranfield, Bedford MK 43 OAJ England. Price £30 (UK), US$72 (Europe), Seawater corrosion handbook, edited by M. M. Schumaker. Noyes Data Corporation Publicity Department, Mill Road at Grand Ave., Park Ridge, NJ 07656. 494 pp. Australian mineral industry quarterly 31(1) 1978 and 31(2) 1978. Bureau of Mineral Resources, Geology and Geophysics, Box 378, Canberra City, ACT 2601 Australia. Subscriptions $8, individual number $2. Mineral and NIM reports Report no. 1996 The extraction of gold from chloride solutions. (10th Nov., 1978). Report no. 1898 Batch and pilot-plant tests on M erensky Reef ore from the Western Platinum Mine. (8th Jun., 1977; reissued 30th Jan., 1979). Report no. 1920 A mineralogical investigation of Mamatu'an and Wessels manganese ores. (15th Sep., 1977; reissued 3rd Jan., 1979). Report no. 1978 The preparation and certification of a referencesample of magnetite ore. (22nd Dec., 1978). Report no. 1998 Electrode response to the addition of zinc during the cementation of gold. (25th Jan., 1979). Report no. 2002 The spectrochemical determination of phosphorus, magnesium, and iron in phosphate rocks and sulphuric acid leach liquors. (26th January, 1979). Report no. 1992 The use of emission spectrometry for the determination of impurities in metals. (24th Jan., 1979). Report no. 2003 An electrodeless conductivity meter of improved sensitivity and reliability. (28th Feb., 1979). Report no. 2005 The spectrometric analysis of manganese-bearing materials with particular reference to ferromanganese slags and metals. (16th Mar., 1979). Report no. 2006 An examination of procedures for the analysis of dry powders by atomic-absorption spectrophotometry. (28th Feb., 1979). Report no. 2007 The instrumentation and computerization of a 25 MV.A submerged -arc furnace. (25th Mar., 1977; reissued 16th Mar., 1979). Corrosion The International Corrosion Council has decided to hold the next Internat ional Congress on Corrosion in Mainz, Federal Republic of Germany, from 6th to 11th September, 1981. Process control The First European Symposium on Real -time Datahandling and Process Control will be held in West Berlin from 23rd to 25th October, 1979. Geomechanics The 28th Geomechanics Colloquy, organized by the Oosterreichische Gesellschaft fur Geomechanik, is to be held at Salzburg on 18th and 19th October, 1979. Geosta tistics A short course on 'Geostatistics for exploration and production planning' is being conducted by the Applied Earth Sciences Department, Stanford University, California, from 27th to 31st August, 1979. Business administration The Twelfth Executive Development Programme of the Graduate School of Business Administration, University of the Witwatersrand, is to be held from 9th July to 17th August, 1979. The engineer and the law A series of four meetings on the above subject is being conducted by the Measurement, Computation and Control SubCommittee of The South African Institute of Electrical Engineers. Lead smelter for South Africa? The National Institute for Metallurgy and Gold Fields of South Africa are making a comprehensive joint investigation of the technical and economic viability of an integrated lead smelter. Conference on titanium The Fourth International Conference on Titanium will be held from 19th to 22nd May, 1980, in Kyoto, Japan.

Jan 1, 1979

By Mike de Wit

Of the approximately 6,500 kimberlites known to date, less than 3% are diamondiferous and less than half of those are economically viable. Admittedly, this is a global figure and varies from area to area much depending on geological, logistical, and political circumstances. The number of diamond-bearing kimberlites is an important geobarometer, and an age-frequency profile has been compiled in order to identify diamond metallogenic epochs and provinces. Four primary diamond clusters have been recognized: Siberia (332-370Ma), Kaapvaal South(114-144Ma), Kaapvaal Southwest(84-95Ma), and Slave (52-55Ma). In addition, three secondary clusters are the Kaapvaal Central (S06-S38Ma), the Man Craton (139-lS3Ma) and the Kasai Craton (120-130Ma). The Kaapvaal is the only area where kimberlites with diamonds were discovered between 1870 and 1925, except for the Prairie Creek discovery in North America in 1906 and Colossus in Zimbabwe in 1907. Between 1906 and 1940 no major diamondiferous kimberlites were discovered, but many of Africa's alluvial deposits were found and exploited in that period. Advances in scientific prospecting in the 1940's rapidly accelerated the discovery rate that peaked in the 1990's; 39 diamondiferous occurrences were found in the 1980's, of which 8 became mines and 5 are in feasibility, and nearly 450ha of kimberlite was added to the global resource base. Despite the accelerated exploration expenditure, the last decade (e.g. 2000-2009) has been the leanest since the 1940's. The most important reason for this decline in exploration success is that any undiscovered deposits are largely buried by younger cover. Understanding complex and geophysical noisy basement geology, as well as decomposition of path-finder minerals are major challenges to further exploration success. Major investments in basic geological expertise and field research will have to be made in order to secure future diamond resources. Integrated geophysical studies, geochemistry diamond forensics, and improved imaging of Earth's upper mantle are perhaps foremost in this requirement, but the costs of these activities are such that government support will be required if countries are to sustain their diamond mining industry.

Jan 1, 2010

Brigadier R. S. G. Stokes of Sherborne, Dorset, is the oldest surviving member of the South African Institute of Mining and Metallurgy. He joined in 1904 and has been a member for 77 years. Book review Sittig, M. Hand book of catalyst manufacture. Park Ridge (U.S.A.), Noyes Data Corporation, 1978. The detailed information in this book is based on patents issued in the U.S.A. that deal with catalysts and their commercial technology. Project management The South African Institute of Mining and Metallurgy is to hold a Colloquium on Project Management in the Metallurgical Industry in March 1980. Ingenieurs-in-opleiding in die weermag Op 'n onlangse vergadering van die Suid-Afrikaanse Raad vir Professionele Ingenieurs is daar besluit om kwytskelding van jaargeld aan geregistreerde ingenieursin- opleiding wat tans met hulle tweejaar nasionale diensplig besig is, te verleen met dien verstande dat.... Engineers-in-training in the army At a recent meeting of the South African Council for Professional Engineers it was resolved that a remission of annual fees would be granted to registered engineers in- training who are doing compulsory two-year national service, provided that.... Processing of fine particles The Society of Mining Engineers of AIME is organizing an International Symposium on Fine Particles Processing, which is to be held in Las Vegas from 24th to 28th February, 1980. Economics of precious metals International Precious Metals Institute announces a Special Course for all interested in economic aspects of today's precious metals.

Jan 1, 1979

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By R. L. Attridge

Namibia's newest mining enterprise, the Navachab Gold Mine, was officially opened by President Sam Nujomo during June 1990. The mine is a joint venture between Erongo Mining & Exploration Company Limited, Metal Mining Corporation of Canada, and Rand Mines Windhoek (Pty) Ltd. Erongo has a 70 per cent interest in the mine, while Metal Mining and Rand Mines hold 20 per cent and 10 per cent respectively. Anglo American Corporation and its associates hold two-thirds of Erongo shares and CDM (Pty) Ltd one-third. The Mine is managed by Erongo Mining & Exploration Company. The property is located some 10 km southwest of the town of Karibib and 170 km west-northwest of the Namibian capital of Windhoek (Fig. 1), the name of the Mine being taken from the farm on which the gold deposits were discovered. Navachab is an opencast operation and was brought into production in December 1989 at a cost of around R84 milion-RS,2 million under budget. The plant is designed to treat 840 kt annually at an average gold grade of 2,6 g/t. This wil produce 1900 kg of gold per year, which at today's prices will earn Namibia more than R60 million in foreign exchange.

Jan 1, 1991

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By K. A. G. Blendulf

The paper describes tests on horizontal-belt filters for the filtration of gold and uranium. The promising results led to the installation of 17 such filters (ten of them 120 m2 in size) in the mine's metallurgical plants, and their operation is discussed. Although several problems were encountered both in operation and maintenance, it is concluded that, with correct operation and suitable filter cloths, exceptionally good metallurgical recoveries can be achieved at filtration rates twice to three times higher than those on rotary filters.

Jan 1, 1997

By J. Meintjes

The measures taken by Rand Carbide Limited from the 1950s to 1976 to control dust emission from the electric furnaces at its Witbank factory are described. A new design of furnace for calcium carbide followed by a dry-fabric filtration plant for the furnace gases was not successful in arresting the dust. A 131 m chimney commissioned in 1968 effectively dispersed the dust-laden gases from both carbide and ferrosilicon production and so brought considerable alleviation. In 1974 a bag-filter dust-collecting plant was successfully commissioned on a 6 MV.A carbide furnace, and this was followed in 1976 by a bag-filter plant on a 46,5 MV.A ferrosilicon furnace. The company has spent considerable effort and money over two decades in trying to combat dust emission, but eventual success had to await technological development.

Jan 1, 1978

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 30th August, 1972. Professor D. D. Howat (President) was in the chair. There were also present sixty-two Fellows, twenty-four Members, two Associates, three Students and eighteen Visitors, making a total of one hundred and nine. The President declared the meeting open at 4.05 p.m. OBITUARIES The President: It is my sad duty to announce the death of six members of this Institute. The first of these is Dr A. J. Orenstein, Honorary Life Fellow, who joined the Institute in 1916 and died on Seventh July. Dr Orenstein became almost a legendary figure in Medicine as a result of his work in the control and elimination of malaria during the digging of the Panama Canal and I believe he was actually engaged working until four days before his death. The other members who have died are: F. Meyer, died on 8th June; S. D. Loxton, Fellow, died on 13th May; J. Innes, Fellow, died on l0th January, 1970; O. B. Prentis, a Member, died on 4th June, and J. Brits, Associate, died on 27th June. As a mark of respect to the memory of the deceased and in sympathy with the bereaved may I ask you to rise and observe a few moments silence. MINUTES The President: 'The second item on the Agenda, the minutes of the meetings held on March 22nd and May 10th, 1972, as tabled. May I confirm these minutes'? Agreed. WELCOME TO VISITORS 'On behalf of the Council, may I say how delighted we are to have such a splendid gathering with us on this our Annual General Meeting. Dames en here vir die omvang van my Afrikaanse woordeskat verdien ek weinig lof, boonop is dit nog Afrikaans met 'n Skotse aksent, wat u asseblief moet verskoon. Tog wil ek se hoe dankbaar ons is dat sy Edele, die Minister van Mynwese, dr Koornhof en mev Koornhof vandag hier teenwoordig kan wees. In addition to our own newly appointed Minister of Mines, we are also honoured by the presence of the Minister of Mines of Rhodesia, Mr I. B. Dillon. I think not even our oldest members can recall an occasion on which two Ministers of Mines were present at a meeting of the Institute. It is a particular pleasure to welcome them this afternoon. I am happy to say that Minister Koornhof is an Honorary-Vice President of the Institute, and Minister Dillon is an Honorary Member. The presence of your goodselves, gentlemen, with us this afternoon, I am sure underlines the great significance which we believe both countries attach to the economic exploitation of the vast mineral resources of Southern Africa. For over 70 years, this Institute and its members have been making their contribution to this great task of mineral exploitation, and we feel that your presence with us today, is a token of the confidence of your governments in what this Institute and its members have been endeavouring to do. Also present with us today, is Mr R. C. J. Goode, President of the Chamber of Mines, and Honorary President of this Institute. I was going to say I welcome Mr Goode, but it is rather difficult to welcome a man to his own home, and this is the case with Mr Goode. He is a very distinguished and a very recent past president of this Institute and he remains now, as he has been for as long as I can remember, one of our most active and valuable members. This I think, ladies and gentlemen, is the second rather unique feature of this occasion this afternoon, because no one else can recollect an occasion on which the President of the Chamber of Mines was also a past president and an active member of our Institute. A special word of welcome, Mr Goode. Mr Tommy Gibbs, our Government Mining Engineer, is in a somewhat similar position as he is also a member and an old and valued friend of our Institute, - welcome to you, Mr Gibbs. Mention I think, must be made of the fact that we are very glad to have with us Dr A. J. A. Roux, President of the Atomic Energy Board, and Mr Stanley Craib, President of the Associated Scientific and Technical Societies. Then, within the great family of the A.S. and T.S., we have the presidents, or the vice-presidents of I believe 13 of the constituent societies. These gentlemen, like all the rest of us, have the rather tiring task of supporting and upholding their fellow presidents on occasions such as this. We particularly appreciate their presence this afternoon and the effort they have made to be with us. We are happy to have with us: Dr R. E. Robinson, Director-General, National Institute of Metallurgy, Mr E. Boden, Manager, Associated Scientific and Technical Societies, Dr H. G. Denkhaus, President, The S.A. Institute of Mechanical Engineers, Mr G. Goedhals, Vice-President, S.A. Institute of Electrical Engineers, Mr E. Dalton, President" S.A. Institute of Certificated

By C. S. Kucukkargoz, A. Bhalla

"The solid-state reduction of ilmenite concentrate with graphite was studied under argon atmosphere at temperatures between 1050°C and 1350°C. The rate of reduction increased with increasing temperature and decreasing particle size, with the maximum extent of reduction found to be 80% at 1350oC with a particle size in the range of -106 +90 µm. The activation energy for the reduction reaction was calculated to be 257 kJ/mole. The trivalent iron oxide was reduced first to divalent iron oxide and then to metallic iron. An annular ring of a partially reduced oxide phase containing metallic nuclei was formed around the core of ilmenite, which grew in size as the original ilmenite core shrank with progressive reduction. The reduction of titanium dioxide also took place during this stage, which produced the Magneli oxides in the form of TinO2n-1. The metallic phase had very high Fe and low Ti contents throughout the reduction, whereas the partially reduced oxide phase adjacent to the metallic phase was high in Ti and depleted in Fe. The metallic phase globules formed during this stage were small and are considered suitable only for leaching and not for other concentration processes. The core of the particle generally retained the composition of the original ilmenite. The purpose of this work was to remove iron and increase the titanium oxide content of the ilmenite to produce a high-titanium containing charge for subsequent smelting.IntroductionThe titanium-bearing minerals ilmenite (FeTiO3) and rutile (TiO2) are the primary natural raw materials used in industry to produce titanium metal and titanium-based products. The common titanium-bearing minerals are ilmenite, rutile, anatase, brookite, leucoxene, arizonite, and perovskite. Although the formula of ilmenite is commonly expressed as FeTiO3, the mineral can accommodate Mn and Mg, which are chemically bound in the form of (Fe,Mn,Mg)TiO3. Ilmenite concentrate can also contain Fe2O3 and Al2O3 in addition to the physically separable oxides such as SiO2 and CaO. The crystal structure of ilmenite is an ordered derivative of the corundum structure with a trigonal-rhombohedral symmetry. Fe2+ and Ti4+ ions occupy the octahedral sites, leaving the tetrahedral sites unoccupied. In each FeTiO3 unit, there are three O2- ions creating three octahedral sites, two of which are occupied by Fe2+ and Ti4+ (Wilson et al., 2005)."

Jan 1, 2017

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2009

By J. Björkvall, L. Bååth, D. Malmberg, J. Malm

Microwave technology has for decades been a tool for astronomers to map and understand the complexities of the universe its composition and extent. It is also used on a laboratory scale by spectroscopists to examine properties of atomic and molecular compounds. In this novel work we will introduce microwave technology to be used for the investigation of liquid slag structures. The preliminary results indicate that the alteration of the slag composition could be correlated to the measured microwave refractive index. Investigations have been performed in the Al2O3-CaO-SiO2slag system. Keywords: Microwave technology, slag, structure, liquid, Al2O3-CaO-SiO2

Jan 1, 2004

By L. Cheng, Y. Liu, Z. Shen, H. Shang, Y. Li

The pre-concentration process of magnetic coarse particles can discharge waste rock or liberated gangue before milling, which is an effective means to reduce cost and increase the efficiency of the concentrator, but the weakly magnetic ore doesn’t have the effective separation method of coarse particle such as hematite, limonite, ilmenite and so on, Because the composite iron minerals contain both strong and weak magnetic elements, the pre-concentration process cannot be applied, or the existing pre-concentration process has problems of complicated configuration and high operation cost. By researching a new type of external magnetic separation technology, the pre-concentration process of composite iron ore was realised by single equipment, which can have a good recovery rate with simple arrangement. In this paper, the separation principle and structure characteristics of the external magnetic separator were researched, and the magnetic circuit characteristics of the external magnet were analysed. The laboratory tests of vanadium titanium magnetite were conducted, and the test results proved that the external magnetic separator can be applied for the pre-concentration process. The industrial application shows that a product of TFe 24.76% with 90.08% recovery, TiO2 10.10% with 91.78% recovery can be achieved from the feed of TFe 20.67%, TiO2 8.33%. Keywords: Coarse particle pre-concentration, composite iron ore, external magnet, magnetic separator

Jan 1, 2020

This report describes the investigational work on the development of a fire-assay method capable of concentrating, in a button of nickel sulphide, all six of the platinum-group metals present in samples of ores, concentrates, and mattes. In the method adopted, the sample is fused with a mixture of sodium carbonate, sodium tetraborate, nickel carbonate, and sulphur. The nickel sulphide formed during fusion collects the noble metals and carries them to the bottom of the crucible. The nickel sulphide button is dissolved, and the noble metals are isolated and determined. The coefficients of variation range between 1,0 and 4,9 per cent for the various platinum-group metals when they are present in concentrations between 0,3 and 75 p.p.m.

Oct 15, 1971

The following is available free of charge from the Bismuth Institute, rue Brederode 9, B-I000 Brussels, Belgium: The chemical analysis of bismuth. Automatic methods of guiding welding heads along butt joints. Investigations into lamellar tearing. A technical survey of seam tracking methods in welding. Review - Seawater corrosion handbook, by M. Schumacher (editor). New Jersey, Noyes Data Corporation, 1979. New journal February 1979 marked the appearance of a new monthly journal, Lloyd's Shipping Economist. New edition Gasification of coal, a basic study of existing processes and new developments, by H. D. Schilling, B. Bonn, and U. Krauss (edited by W. Peters). Essen (West Germany), Verlag Gltickauf GMBH, 1979. 2nd revised edition. 336 pp. 68DM (approximately R32). In German. South African technikons The six autonomous colleges for advanced technical education in South Africa were established in terms of the Advanced Technical Education Act (Act 40 of 1967). However, since the inception of these colleges, it has become clear that members of the public find the name difficult to use and to remember. Consequently, these colleges, which play such an important role in the community, were not always correctly identified. Die forging The 9th International Conference on Die Forging will be held from Monday, 4th to Saturday 9th May, 1981, in Diisseldorf, Federal Republic of Germany. It is being organized jointly by the Forging Committee of the Verein Deutscher Eisenhiittenleute and the Vereinigung Deutscher Freiformschmieden. High-temperature alloys An International Conference on the Behaviour of High Temperature Alloys in Aggressive Environments will be held in Petten (North-Holland) from 15th to 18th October, 1979. Strategic minerals The National symposium on the availability of strategic minerals, which is being organized by the Institution of Mining and Metallurgy in collaboration with the Fellowship of Engineering, will be held at the London Press Centre, New Street Square, London EC4, on 20th and 21st November, 1979. The symposium has as its main objective consideration of those minerals that may pose problems of availability in the United Kingdom. Underwater mining The 10th Annual Underwater Mining Institute is scheduled for 1st to 3rd October, 1979, at Galveston, Texas. The Institute will be cosponsored by the Sea Grant College Programs of the University of Wisconsin and Texas A & M University and by the Marine Science Institute of the University of Texas it is being held in co-operation with the Association for Marine Mining. Die Suid-Afrikaanse Instituut Vir Mynbou En Metallurgie - Inligting Oor Lidmaatskap.

Jan 1, 1979

By Phil Morriss

During the last 12 months, Sandvik?s Technical Service Group has carried out nine Scoping and Pre-feasibility studies for the application of In-pit crushing and conveying (IPCC) for large mining companies; the majority in conjunction with the Snowden Consulting Group. During these studies several key and recurring drivers have been identified: 1. Mining schedule issues ? there are several issues which crop up repeatedly, including: ?the unnecessary curvature of pit walls, ?very high rates of vertical advance which are (created by schedule optimisers to minimise stripping at all times) which are at the limit of what can be realistically achieved (and which of course make it harder for IPCC to achieve any impact), and ?The allocation of material to semi-mobile systems to maximise the ability for IPCC to be an effective alternative. 2. IPCC productivity issues ? the key issues are the IPCC system operating hours achievable, and the system throughput (both instantaneous and the average). 3. IPCC Risk issues ? there are perceptions about the risks associated with the use of IPCC which are a mix of reality and fiction, but which nonetheless create negativity towards the use of IPCC. In this paper, the authors wish to address specifically the factors affecting the IPCC productivity.

Jan 1, 2008

By C. N. Eze, C. K. Ezeh, O. Nnabuife, N. M. Ugwoju, S. C. Enemuor, V. Okechukwu

In this study, the efficacy of Providencia vermicola KUBT-1 in the leaching and beneficiation of Agbaja iron ore was evaluated under varying conditions of temperature, ore particle size, and pH. Agbaja iron ore is a Nigerian low-grade ore containing about 43%–52% iron and a high amount of gangue materials, including phosphorus (1.4%–2.0%) and sulphur (0.12%). The study was organised in triplicate in shake flasks with 48 samples. One millilitre of washed cells of Providencia vermicola KUBT-1 suspended in normal saline at 0.5 McFarland standard (108 cells ml-1) was introduced into each flask containing 50 g of sterilised ore in 100 ml of bioleaching medium, and the samples incubated at room temperature for eight weeks. The levels of upgraded iron, mobilised sulphur, and phosphorus were determined by atomic absorption and ultraviolet spectrophotometric analyses, respectively. Results showed that a particle size of 0.8 mm was optimal for iron upgrading and sulphur mobilisation while 1.0 mm ore size was optimal for phosphorus mobilisation. Up to 89.60% of the iron was upgraded while phosphorus and sulphur were mobilised, leaving residual values of 0.223% and 0.02%, in the ore, respectively. The organism produced best beneficiation results at a pH of 2.5 and a temperature of 3ºC. Correlation analysis with the Pearson’s correlation model showed a positive correlation between iron upgrading and sulphur-phosphorus removal (r =1.000, and r =0.967), respectively. These results present Providencia vermicola KUBT-1 as a promising candidate for large scale leaching and beneficiation of Agbaja iron ore.

Dec 15, 2025