Search Documents

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016

The following letter has been received from Professor P. A. Young, Head of the Department of Mining and Mineral Engineering at The University of Leeds, England. Extractive and process metallurgy The first annual TMS-AIME Extractive and Process Metallurgy Fall Meeting:1983 International Sulfide Smelting Symposium, will be held from 6th to 9th November, 1983, in San Francisco.

Jan 1, 1982

By A. J. Jager, D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2004

By W. A. Lenhardt

During the past five years, several research projects on the causes of mining induced seismicity have been carried out by the Rockburst Research Department at Western Deep levels Limited. This paper summarizes the results of these investigations. Several types of mining-induced seismic events are addressed, and models of their mechanisms are presented. It is shown that most of the seismicity results from mining in geologically disturbed areas, and ways and means are discussed to reduce the seismic potential. Stabilizing pillars, for instance, have been introduced to reduce stresses at the stope face and to alleviate the facebursting problem. Facebursts still occur in areas of very low stresses, and pillars became the source of very large seismic events (M >3). At this stage, the understanding gained of pillar-associated events allows a review of current mining practices. Further, it makes possible an examination of the efficiency of measures to alleviate the effects of various seismically prone situations.

Jan 1, 1992

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By P. G. Kovalchik

Overexposure to noise remains a widespread, serious health hazard in the US mining and other industries despite 25 years of regulation. Most categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. The drilling of rock in a confined work environment contributes to high levels of noise exposure in mining. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the noise exposures of jackleg drill operators and to prevent additional cases of noise induced hearing loss (NIHL) by developing and evaluating low-cost retrofit noise controls for equipment. This report describes the procedure for the measurement and reporting of noise from portable pneumatic tools such as jackleg drills. The technique used in this research allows for the determination of the source A-weighted sound power levels and the radiation patterns in octave and 1/3 octave bands. Overall sound power level is also determined. This paper also reports the results obtained by using this procedure to evaluate a SECO S215 standard production drill and a CSIR Miningtek prototype rock drill incorporating engineering noise control measures. It was found that by using the manufacture?s recommended operating pressure of 496 kPa (72 psi) that the CSIR prototype?s sound power was 10 dB(A) less then that of the SECO S215.

Jan 1, 2009

Publications of the 13th CMMI Congress, by J.T. Woodcock (editor-in-chief). Melbourne, Australasian Institute of Mining and Metallurgy, 1986. Set $A90,00. Reviewer: J.D. Austin

Jan 1, 1988

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By M. S. Shishvan, J. R. van Duijvenbode, L. M. Cloete, M. W. N. Buxton

Geochemical and mineralogical datasets from Tropicana Gold Mine, Australia, have been used to define ore fingerprints. VNIR/SWIR spectral data were represented by four normalised wavelength regions and were clustered to form spectral classes. Sequentially, these spectral class proportions within a block and collocated XRF data were clustered to form material types (fingerprints). The material types were related to an Equotip-BWi correlation. These correlations can be used to extrapolate a hardness signature and generate a BWi proxy for different blocks. The combined fingerprints and BWi proxy can assist as a tool for enhancing the prediction of comminution behaviour. They can explain specific domain-related hardness variations. For example, one material type could be separated into a softer (~15-18 kWh/t), and harder (>20 kWh/t) material blend. This was accomplished using the commonly overlooked VNIR region at 605 nm. This outcome has significance for blending strategies.

Sep 1, 2021

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

International Solvent Extraction Conference 1971 ISEC '71, which will be held in The Hague, The Netherlands, from 18th to 23rd April, 1971, is being sponsored by the Society of Chemical Industry in association with the Koninklijk Instituut van Ingenieurs, the Institution of Chemical Engineers and the Koninklijke Nederlandse Chemische Vereniging. The Working Party on Distillation, Absorption and Extraction of the European Federation of Chemical Engineering is participating in the Conference, which is the 101st event of the Federation. The scope of the Conference covers the entire science and technology of liquid-liquid extraction as applied in all branches of industry. Thus sessions will cover both chemical and chemical engineering aspects of the subject as applied to both inorganic and organic solutes. The conference aims to bring together academic and industrial workers in the field from all parts of the world. The programme includes over 100 papers by authors in 26 countries. Full details of the papers, together with registration forms, are contained in a detailed programme, copies of which are now available from: ISEC '71, 14 Belgrave Square, London, S.W.1, U.K. Department of Mining and Mineral Technology of the Royal School of Mines Postgraduate Courses Technical and economic challenges facing the minerals industry, together with progressive change in methods and equipment, increasingly necessitate re-training of experienced professional engineers who aim for top places. In order to meet this need, this Department has for some years run one year M.Sc. courses. Engineers, often sponsored by their employers, have a choice of three courses which are respectively devoted to mining, applied rock mechanics or mineral process design. The course in Mining is divided into five subjects, which are treated from the business management point of view. It is intended to provide middle management with a knowledge of those techniques that are required by the mining engineering function in the preparation of modern projects. The course in Mineral Process Design provides a systematic use of mineral sciences, engineering and economics for ore testing and process design, so as best to balance the technical and financial requirements for specific mineral resources. The course in Engineering Rock Mechanics is designed to provide a specialized training in the engineering applications of rock mechanics for engineers and geologists, so that they are equipped to treat a wide variety of problems in mining and civil engineering. Prerequisite qualifications are a good first degree in a related subject, plus industrial experience: The rewards include an M.Sc. of the University of London and the Diploma of the Imperial College (DIC). The limited number of places available (12 in each group) makes early application advisable. Full details are available from the Registrar, Imperial College, London, S.W.7.

By B. Kruger

After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron. The iron-free (less than 1% Fe) converter matte is granulated and sent to the base metals and precious metals refineries for further processing. During the smelting and converting processes two distinct gas-strength gas streams are produced: ?The Peirce Smith converter off-gas contains 4%?9% SO2which is treated in a conventional sulphuric acid plant to produce 94% H2SO4. ?The electric furnace off-gas contains 0.9% SO2which was (until September 2002) vented through a 91- metre high stack to atmosphere. In October 2002 Impala Platinum commissioned a SULFACID® plant at its smelter in Rustenburg, which recovers the SO2from the electric furnace off-gasses into a weak sulphuric acid solution. The SULFACID® technology utilizes wet activated carbon to oxidize the SO2toSO3. The SO3reacts with the water on the catalyst and is washed off the catalyst bed as a sulphuric acid solution with up to 13 wt. H2SO4. The plant operates at 60ºC and at atmospheric pressure. The SULFACID® technology is widely used in the pigment industry. This is, however, the first application of the technology on electric furnace off-gas. Keywords: SO2, sulphuric acid, electric furnace, off-gas, SULFACID®

Jan 1, 2004

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By F. H. Guise-Brown

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. WILSON and P. C. GRAHAM Published in the Journal, October, 1972. Discussion by F. H. Guise-Brown., B.Sc. (Min. Eng.) (Member) INTRODUCTION Messrs J. W. Wilson and P. C. Graham are to be congratulated on an excellent paper containing several thought-provoking remarks. The concept of allocating a machine and equipment valued initially at some R300 000 on an experimental basis is courageous, and the results obtained could be of interest to the mining industry as a whole. The Gold Fields of S.A. Group approached this problem differently. In pioneering the start of this work in South African gold mines, they considered that expenditure of this magnitude would be warranted only if the proposition was viable right from the start. To this end, a Robbins R41 was purchased expressly to assist in the duplication of part of the No. 1 shaft system of the Doomfontein Gold Mine. Mr M. J. Koortsl has summed up the initial results of this work and given some preliminary costing, but inflation since that period has made these figures somewhat out of date.

Jan 10, 1972

By T. Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques and controlled bulk leaching studies. The anodic dissolution process has been established to be a sevenelectron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions, which suggests that the sulphur is oxidized to thiosulphate and the copper and iron released as Cu+ and Fe2+ in these systems. The deportment of Fe2+ and S2O3 2- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, supporting formation of different sulphur species as proposed for the sulphate and carbonate salts. Scanning electron microscopy and energydispersive spectroscopic analysis of the mineral surface after leaching indicate presence of an iron–sulphur surface layer completely free of copper in the sulphate system, an iron-rich surface layer in the perchlorate solutions, and absence of surface layer build-up in carbonate solutions. XRD analysis of a bulk leach residue from leaching in ammoniaammonium sulphate solutions showed the surface layer to be mostly amorphous (90%). The crystalline content (10%) is composed of 95% polymorphs of anhydrous iron oxide hydroxide FeO(OH). Choice of ammonium salt and the hydrodynamic environment of leaching have been shown to influence the presence or absence of the surface product, as well as its nature. IntroductionHydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different routes for hydrometallurgical treatment of chalcopyrite can be followed. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilization of copper (I) and copper(II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation [1] (Beckstead and Miller., 1977a):"

Jan 1, 2016

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By J. Nell

Heavy mineral deposits often contain relatively high levels of radioactive elements (thorium and uranium in particular).It is difficult to obtain clean separation of ilmenite and monazite (the main impurity mineral containing radioactive elements), and physical intergrowths of the two minerals are, in fact, not uncommon. As a result, ilmenite concentrates obtained from such deposits often contain high levels of thorium and uranium. Because of the large negative free energies of formation of ThO2and U3O8boththorium and uranium report to the slag during smelting and if an ilmenite concentrate contaminated with monazite is used to make high titania slag, the concentrations of these elements in the slag end up about 40% higher than in the ilmenite feed. Previous work, patented by RGC Mineral Sands Limited, and subsequently confirmed by Mintek, showed that radioactivity may be reduced by roasting an ilmenite concentrate with borax at 1000°C to 1100°C and leaching it with hydrochloric acid1. It is evident that the cost of an ilmenite roast/leach process will be high and there may be economic benefits in removing the radioactive elements from the slag instead (the volume of slag to be treated is smaller than the volume of ilmenite feed). To remove radioactive elements from the slag it is necessary to know how these elements occur in the slag. Inother words, the distribution of uranium and thorium between the various oxide, silicate and metallic phases in high titania slag must be determined. Once the deportment of thorium and uranium between the various phases ha sbeen determined, an appropriate process for slag purification can be developed. Test samples High-titania slag was prepared in a pilot-scale DC furnace from ilmenite concentrates with different levels of uranium and thorium. Subsequently, ten slag samples representing a range of compositions were selected for bulk chemical analysis, scanning electron microscopy and micro-analysis. The samples were crushed to a maximum particle size of 1 mm and from each sample a 20-kg batch was riffled out for analysis. Bulk chemical composition Chemical compositions of the samples selected for test work are given in Table I. TiO2, Al2O3, SiO2, MgO, MnO, FeO and V2O5were analysed by ICP-OES, Na2O, CaO andCr2O3by atomic absorption spectroscopy and U and Th by XRF (the XRF detection limit for U and Th was around 4 ppm). The ?B? series has a higher silica content than the others as a result of small silica additions that were made during smelting. All samples have elevated alumina levels as a result of furnace refractory contamination during smelting. As expected, there is an inverse relationship between the concentrations of TiO2and FeO in the samples (Figure 1).The TiO2and FeO levels are similar to the levels found in industrial slags2. Extreme conditions of reduction under which reduction of more ?refractory? oxides (e.g., chromia, magnesia, silica, alumina and even urania and thoria) might take place were not explored in the study. Note that BB1and BBB1 contain more than 7% combined silica and alumina (SiO2as a flux addition during smelting, and Al2O3from refractory contamination) and they do not fall on the general trend defined by the other samples. The U and Th concentrations of sample E2 is noteworthy. In the preparation of slag E2, monazite concentrate was added to the ilmenite to increase the concentrations of radioactive elements in the slag. This was done primarily to facilitate the detection of Th and U during the phase chemical characterization of the slag. Radioactivity measurements Gamma ray emissions from the samples were measured [ ]

Jan 1, 2007

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

By O. A. W. Strydom, J. C. M. Wethmar, P. R. Jochens, D. D. Howat

Liquidus temperatures in the Cr-Fe-Si system in the composition range representative of ferrochromium-silicide produced in South Africa J. C. M. Wethmar, B.Se. (Eng.) Rand D. D. Howat,U B.Se. (Glas.), Ph.D.. F.I.M. P. R. Joehens, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. O. A. W. Strydom, M.Sc., Ph.D. Alloys in the composition range of chromium, 20 to 50 per cent, iron, 10 to 30 per cent, and silicon, 25 to 55 per cent, were subjected to both differential thermal analysis and the classical quench method so that the liquidus temperatures of ferrochromium-silicide alloys could be determined. The results are presented as liquidus curves on pseudo-binary sections at various ratios of chromium to iron and as liquidus isotherms in the ternary section.

By T. Scheldt, M. Lu, A. Myrvang

Abstract: In this paper both continuous and discontinuous modelling are utilised in order to analyze the stability of the Gjøvik Olympic Mountain Hall. The large span cavern (62 m) was built for the 1994 Winter Olympic Games at Lillehammer, and is a unique case study because of the large amount of available input data, through a comprehensive pre-investigation, stress and deformation monitoring program before, during and after the excavation. Phase2, a two-dimensional non-linear finite element program, and the Discontinuous Deformation Analysis (DDA) are used as representative tools for continuous and discontinuous modelling, respectively. The analysis results are compared and discussed taking the reliability of the models, time-consumption and costs into consideration. Some guidelines for the total modelling process, from field measurements to final results, are also presented. Zusammenfassung: In diesem Artikel werden sowohl kontinuierlich als auch diskontinuierlich Modellierung verwendet, um die Stabilität, der in den Berg gebauten Olympiahalle in Gjøvik zu analysieren. Die Olympiahalle wurde 1994 zu den Olympische Spielen in Lillehammer errichtet. Ihr Dach erstreckt sich über eine Breite von zweiundsechzig Meter. Für den Bau wurden umfangreiche Daten durch Voruntersuchungen, und Überwachung von Gebirgsspannungen und Deformationen bevor, während und nach Exkavation eingesammelt. Auf Grund dieser großen Datenmenge stellt die Olympiahalle ein herausragendes Beispiel für den Bau ähnlicher Projekte dar. Für die kontinuierlichen Modellierungen wurde „Phase2“, ein zwei-dimensionales, nicht lineares „endlich Element“ Rechnerprogramm angewandt. Die diskontinuierlichen Modellierungen erstellte man mit Hilfe von der „Diskontinuierliche Deformations Analyse“ (DDA). Die Analysenergebnisse sind mit Rücksicht auf die Zuverlässigkeit der Modelle, Zeitverbrauch und Kosten verglichen und diskutiert worden. Im Artikel werden Richtlinien für den Modellierungsprozess von Dateneinsammlung bis Schlussfolgerung gegeben. Résumé: Dans cet article la modélisation continue et discontinue sont utilisés pour analyser la stabilité de Gjøvik Olympic Mountain Hall. Cette caverne de grande portée (62 m) a été construite pour les Jeux Olympiques d’Hiver de 1994 à Lillehammer, et est une étude de cas unique grâce à la grande quantité de données disponibles, de par un programme de pré-investigation compréhensive, monitorage des contraintes et déformations avant, pendant et après l'excavation. Phase2, un code d’éléments finis non linéaire à deux dimensions, et l’Analyse en Déformations Discontinues (DDA) sont utilisés comme outils représentatifs de la modélisation continue et discontinue, respectivement. Les résultats d'analyses sont comparés et sont discutés, prenant en compte la fiabilité des modèles, la consommation en temps de calcul et les coûts. Quelques indications pour le procédé total de modélisation, des mesures sur place aux résultats finaux, sont aussi présentées.

Jan 1, 2003