Search Documents

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

Primary roof support represents the first line of defence against rockrelated falls of ground in underground mines, and improper utilization or misunderstanding of the applicability and behaviour of primary support can be costly from a safety standpoint. This is a major concern for underground mines, as roof support is the single most costly expense from a mining operational perspective. This is further backed by the evidence that, in the USA, hundreds of injuries and fatalities still occur each year because of rib, roof, and massive roof falls. Additionally, the fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical anchor bolts, which constitute a large portion (89%) of the 68 million bolts installed each year in underground mines in the USA can vary in cost quite dramatically. To mitigate this concern a study was conducted in 2010 by the National Institute of Occupational Safety and Health, in conjunction with Southern Illinois University of Carbondale, to assess the performance of primary roofbolts in underground coal mines for improved safety and cost. This was accomplished using underground roofbolt monitoring solutions, field data, and numerical modelling to better understand the quasi-static behaviour of underground coal mine roofs and the response behaviour of the bolts. In particular, over 170 instrumented extensometers, closure meters, shear meters, fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical roofbolts were installed at three coal mines across the USA. Of these three mines, two used the room and pillar extraction method and the other used the longwall extraction method. There was no evidence to indicate a difference in performance of the active primary roofbolts compared with the passive primary roofbolts. Additionally, in the initial loading phase, the active bolts showed no difference in loading, indicating that tension bleed-off is of more of a concern than originally thought. Lastly, for the initial computer modelling studies, challenges still remain in obtaining a good match to the in situ bolt measurements and replicating the discontinuous roof rock and in situ bolt behaviour over time.

Jan 1, 2014

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By M. Grave

Rock Engineers are required to design safe cost effective support systems and stoping layouts for their respective mines. As each stope has its own unique environment, continual re evaluation is required in all stopes to maximize extraction and achieve value from the support standard. This paper presents numerical modelling used to plan early mining within the shaft pillar and a reevaluation of an existing stope support standard.

Jan 1, 2009

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By D. Bessinger, H. Kotzé, J. Beukes

Keywords: Pyrometallurgy, furnace, ilmenite, smelting, Ticor Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and Mineral Separation Plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2 slag and 145 kt/a of pig iron.

Jan 1, 2006

By Ron Tluczek

[Power Point Presentation]

Jan 1, 2006

By Willem J. Marais

The management of unpaved mine road networks on large surface mines rarely results in optimal road maintenance strategies and minimised total road-user costs. This is ascribed mostly to the complex and dynamic combination of variable road networks and loading and discharge points. In a dynamic mining environment - typically those mines in which production is managed by a centralised truck dispatch system ? there is no guarantee that a particular road maintenance intervention will contribute significantly to reducing total road-user costs or increasing productivity. Most large surface mines operating ultra-heavy mine trucks rely on an integrated on-board diagnostic data collation, communication and GPS-asset location system as a real-time fleet management tool. By extending this system to incorporate a multi-sensor analytical procedure in which specific truck vital signs are monitored and filtered, a road defect can be recognised and a trigger level set to relay the location of defects on the mine haul road to the centralised truck data management system. Previous work established the feasibility of the multi-sensor approach to road defect recognition on large mine haul trucks, and outlined the defect recognition, analytical and modelling issues and system limitations. This paper presents the development of the analytical procedure used as a basis for evaluating the truck on-board data to establish maintenance priorities amongst a network of mine roads. Following an introduction to the system architecture, the results of system field trials are analysed and the results discussed in the light of defect density and traffic volume as the primary variables in an approach to prioritising road maintenance. The paper concludes that by supplementing the existing mine communication and asset management systems, road maintenance can be managed on a near real-time basis and maintenance equipment dispatched to where most immediate benefit will realised from a maintenance intervention on the network, thereby generating the maximum improvement in service and reduction in cost per ton hauled.

Jan 1, 2008

'We are going to be short of engineers for the foreseeable future, and particularly short of civil and heavy-current electrical engineers'. This is the basic message that emerges from the report 'The supply of and demand for engineers, 1984,t, prepared by Dr Philip Lloyd and Professor Bob Plewman for the Federation of Societies of Professional Engineers (FSPE).

Jan 1, 1985

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s and is recognized a shaving significant potential for optimizing production scheduling problems for both surface and underground mining. The major problem in long-term production scheduling for underground orebodies generally relate to the large number of variables needed to formulate a MIP model, which makes it too complex to solve. As the number of variables in the model increase, solution times are known to increase at an exponential rate. In many instances the more extensive use of MIP models has been limited due to excessive solution times.

Jan 1, 2010

By D. -X. Li

The paper covers many literature reports of processes using nitrogenous species as an oxidant for processing refractory gold ores, especially development in the pretreatment of refractory gold minerals by nitric acid. These processes include the high-pressure and the atmospheric-pressure oxidation methods. High-pressure oxidation processes are difficult to carry out, because they require high-capital cost autoclaves. Atmospheric-pressure oxidation processes are easier to manipulate, but complete absorption and reuse of NOx is difficult or multiple-stage absorption must be established for its reuse. So, some new methods were developed, such as catalytically oxidizing technology of NOx to allow subsequent recovery of gold. Keywords: nitric acid; pretreatment; refractory gold

Jan 1, 2009

By K. H. Berget, V. Andersen, H. Tveit, R. Jensen

This paper presents some of the work carried out in order to improve the tapping process in silicon production, with special focus on the environmental and the safety standards. Some of the modelling work that has been done to improve the understanding of the process is described, together with the resulting implementation to improve tapping standards.

Jan 1, 2014

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By Z. Song

Real-time monitoring makes it possible to detect any disturbance occurring in production, while decision instruments can efficiently assist decision-makers to optimize production, reduce iterative workload, obtain better solutions, and preview possible results. Technologies for the above already exist and have been proven in the process industry, i.e. refining and smelting. Optimization is also essential for profitable and stable mining production. Real-time monitoring has already taken hold in mining operations, especially in surface mining, while optimization techniques have also been widely used in underground mining, particularly for planning and scheduling. This review is limited to the hard-rock mining production of metallic ores such as gold and copper. It reviews optimization techniques developed for mine planning and scheduling, and communication technologies suitable for underground applications. It also presents control features for individual operation units, and discusses the technical viability of a mining production real-time optimization (MPRTO) system for underground mines, with possible benefits and challenges. Operational disturbances always occur in mine production. An MPRTO system can be useful to maintain operational effectiveness and efficiency by allowing quick changes to short-term plans. This paper briefly describes the MPRTO system, including the input, output, and basic algorithms. The technical prerequisites for the system specified here are already available. Further studies that are required to improve the system are discussed. Keywords real-time optimization, underground mining, production, operation.

Dec 1, 2013

YEAR 1943-1944 Vol. 44 Page A major change-over in the ventilation of a deep level mine, by F. G. Hill and E. C. Ranson, 27; Discussion 56, 62, 67, 71, 72, 79, 123, 129 131 A note on the quarrying of surface limestone in the Sinai Desert, by V. L. Bosazza.. .. 59 Mining with diamond drills at the Nkana Mine of the Rhokana Corporation, Limited, Northern Rhodesia, by W. A. Odgers and A. G. Stirling, 95; Discussion 117, 121, 122 123 On silicates and dusts from the Witwatersrand gold mines (some preliminary notes), by J. J. Frankel, 169; Discussion .. 178 Presidential Address-Review of the rock pressure problem, by C. Biccard Jeppe, 3; Discussion 11,15 17 The chemistry, production and application of plastics, by P. N. Lategan, 138; Discussion 151 153 YEAR 1944-1945 Vol. 45 Page A microtechnique for the size-grading of mine dust, by S. R. Rabson, 34; Discussion 49, 50, 52 55 Activated carbon for regenerating used lubricating oil, by F. J. Tromp and J. J. Matthee 90 A contribution to the study of the production of zeolites, by C. C. le Grange and A. J. Petrick 235 A laboratory method for the determination of the suitability of South African coal and coal blends for the manufacture of metallurgical coke, by R. F. J. Teichmann .. .. 202 Copper containing cements for self-sanitising surfaces, by R. S. Young and H. L. Talbot 156 Notes on some sulphide minerals from the Far East Rand, by E. Mendelssohn, 84; Discussion, 88 89 Presidential Address-A review of underground support on the Witwatersrand with its Bearing on the Problem of ultradeep mining, by P. J. Louis Bok, 3; Discussion, 24, 25 27 Scientific management with particular application to a Witwatersrand gold mine, by J. S. Ford, 63; Discussion, 77, 80, 82 83 Some aspects of rock-drilling practice (the Witwatersrand gold field), by C. J. Irving, 163; Discussion, 185, 190 *197 Temperature measurements in a mine on the Witwatersrand with an electrical resistance thermometer, by O. Weiss, 127; Discussion, 136 137 The measurement of the geo-thermic gradient by means of the clinical thermometer, by R. A. H. Flugge-de Smidt, 105; Discussion, 136 137 The micro-chemical determination of free and combined silica in mine dust, by S. R. Rabson, 43; Discussion, 49, 50, 52 55 The oxidation of pyrites associated with South African coals, by R. F. J. Teichmann 141 YEAR 1945-1946 Vol. 46 Page Air cooling plant, No. 4 Shaft, City Deep, Limited. A review of layout and results achieved, by H. W. Unwin, A. Malcolm and R. E. Campbell Pitt, 66; Discussion, 100, 102, 103, 106, 110 115 A preliminary note on the Waterberg coal field as a possible source of coking coal, by P. E. Hall 124

By J. A. L. Napier

The evaluation of stress distributions and deformations in the vicinity of tabular mine layouts has been carried out routinely for many years using the displacement discontinuity boundary element method (DDM). In this approach, mine layouts are approximated as irregular shaped planar cracks (or slits) where the ?width? of the crack, corresponding to the excavation height, is assumed to be negligible compared to the in-plane, lateral dimensions. Early implementations of this approach have employed square element tessellations with constant displacement discontinuity component values. This is generally restrictive when considering the analysis of irregular pillar layouts or the intersection of fault planes with excavations. This paper describes a general revision of this approach in which triangular or quadrilateral element shapes are introduced in conjunction with higher order variations of the displacement discontinuity shape functions. This facilitates an accurate evaluation of detailed stress and displacement components close to excavation surfaces and allows the investigation of local damage and failure behaviour associated with particular geological structures such as weak parting bands or weak layers. A method to embed these features in an efficient and accurate multi-level solution scheme is described. This formulation can be extended to allow the analysis of shallow-depth pillar layout problems, facilitating the assessment of the interactive response and stability of shallow depth pillar layouts. A simple deformation model is introduced to facilitate the assessment of pillar failure and bursting potential in shallow mine layouts. The computational techniques described here have been implemented in a computer code called TEXAN (Tabular EXcavation ANalyser) and are illustrated by the simulation of a particular multiple reef pillar mining problem in a shallow depth platinum mine.

Jan 1, 2007

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

By R. P. H. Willis, A. G. du Plessis, R. B. Wilson

This paper reviews issues to be considered in choosing primary access and transportation options for platinum and other mines. It proposes appropriate criteria and a methodology for deciding on the optimum primary access option for any particular orebody. Also included are generic parameters that can be used to facilitate the process of choosing the optimal access option.

Jan 1, 2004