Search Documents

By K. C. Corin, M. S. Manono

The mining and mineral concentration of Cu-Ni-PGM sulfide ores in South Africa occurs in semiarid regions. The scarcity and availability of water resources in these regions has become one of the biggest challenges facing mineral concentrators.S Owing to this challenge, concentrators have to find ways through which they can manage and control their water usage. Recycling and re-use of process water in mineral concentrators has therefore become common practice. This practice is beneficial in that it reduces reliance on municipal water, harnesses compliance to stringent environmental regulations on water usage, and it also offers a better response to the Sustainable Development Goals. This could however be somewhat concerning to the operator as recirculated water often has higher concentrations of ions compared to fresh or potable water. The unintended change in the process water quality may potentially affect critical aspects of flotation such as the stability of the froth. This has led to the need to find those process water ions that have the greatest impact on froth stability. Thus, this paper investigates the effect of various ions common in process water of a typical Cu-Ni-PGM concentrator on froth stability. Bubble size, water recoveries, foam height, and dynamic froth stability in both twophase and three-phase flotation systems are used as proxies for froth stability. Findings of this study are deemed crucial towards the development of a process water management protocol in sulfidic Cu-Ni- PGM ore concentrators. Keywords: Bubble diameter, electrolytes, flotation, froth stability, water quality

Jan 1, 2020

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010

This paper examines manning best practice in the Australian mining industry, comparing the mining of gold with mining of other commodities. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 7 open pit and 14 underground studies of gold mines in Australia from a database of over 50 studies. The data were collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2009. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. The proportion of supervisory to operations personnel and labour costs as a percentage of total operating costs is highlighted. Minimum manning requirements for the range of mining methods are indicated, irrespective of the size of the operation. The benchmarking results provide guidance by indicating a range of manning numbers and trends which are likely to be appropriate for the scale and type for a range of mining operations. When combined with benchmarked productivity and cost data, manning results help identify potential areas for business improvement, driving gains in the efficiency of labour. Finally, the paper considers perspectives on best practice for manning and the limitations in application of this type of analysis in a global context.

Jan 1, 2009

In the previous chapters we did not concern ourselves with the fact that the geostatistical properties of the regionalized variable x (z) are affected by the size of the support w. Ideally, when analysing an ore body O, we would like to determine the properties of point values in O, i.e. the properties of a regionalized variable with an infinitely small support, say w°. In practice, point values are never known. To measure the value of x at a point z we must take a sample of size w centred at z. For example, if we are interested in the grade at point z, w will be the volume of the sample 'centred in z; if we are interested in the metal accumulation at point z, w will be the area of the cross-section of the sample centred in z. We say that the measured property is a regularized variable, and so the semivariogram (or covariogram) calculated from the values obtained is also regularized. In the majority of the mining problems which can be solved by geostatistical methods, we are interested in the properties of blocks of ore and of samples with a finite non-point support. It will be shown in the following chapters that these problems can be solved by calculating the average value of the point sernivariogram in volumes or areas of finite dimension, or between such volumes or areas. These calculations would be simple if we knew the point semivariogram. This means that the point semivariogram has to be estimated from the observed regularized semivariogram(s).

Jan 1, 1978

By P. M. Solozhenkin, O. I. Solozhenkin

Currently lead nitrate is used as the recommended activator in Au-Sb flotation. However, due to high levels of hazard, the application of lead nitrate constitutes a potential risk for human health and ecosystems. To mitigate the harmful impact of activators on the environment, further research on activation by alternative reagents has been launched to promote the efficiency of antimony ores. In the present study, adsorption of lead, copper and zinc cations has been investigated by nuclear quadrupole resonance (NQR), which has revealed copper and zinc cations penetration into the mineral lattice, although lead cations remain adsorbed on the mineral surface. However, the combination of zinc and copper cations leads to preferential volumetric adsorption of zinc in the mineral lattice and further surface adsorption of copper which positively affects the activation process. It has been established that activation of stibnite can be achieved effectively with the mixture of Cu2+:Zn2+=1:1 as much as with lead cations in antimony ore flotation. As a part of this work, the computational modelling has been used in prognosis of reagent activity evaluation (PRAE) for stibnite and aurostibite flotation by sulfhydryl collectors. The lower PRAE value the stronger the ability of a collector to form a stable complex with a mineral. PRAE has shown a strong negative trend to complex formation on the mineral surface of aurostibite and stibnite. Based on these studies, several collectors have been proposed for effective flotation. To verify the feasibility of proposed collectors tetramethyl (ethyl) thiuram disulfides (TMTD and TETD) have been used for flotation of stibnite, sphalerite, pyrite and arsenopyrite. Flotation performance has been improved significantly with TMTD that allows the avoidance of lead nitrate application and increases the recovery of antimony by 8,16%. Keywords: Stibnite, aurostibite, activation, lead, copper, flotation reagents

Jan 1, 2020

By K. -I. Higuchi, M. Mizutani, K. Haga, A. Shibayama, A. Batnasan

In recent years, the quality of iron ores has decreased due to the increase in the content of impurities, namely quartz, aluminum, phosphorus, and sulfur. It indicates that the removal of impurities from iron ore is an extremely challenging task. In particular, the high amount of phosphorus in iron ore could be a problem for energy consumption and CO2 emission in the steelmaking process. To reduce the impact of phosphorus, mainly two approaches: the utilisation of low-phosphorus iron ore, or dephosphorisation of high-phosphorus iron ore using mineral processing technology, have been suggested. In this paper, the removal of phosphorus from a low-grade high-phosphorus iron ore containing 0.1 mass% P and 57.5% Fe by alkaline roasting and wet grinding is discussed. The iron ore consists mainly of hematite, goethite, and quartz. Effects of sodium hydroxide concentration used as an alkaline source, roasting temperature, grinding time, and particle size on the dephosphorisation of highphosphorus iron ore were investigated. The dephosphorisation efficiency, iron loss, and mineralogical components of low-grade high-phosphorus iron ore under various experimental conditions were characterised by using XRD, SEM-EDS, and particle size distribution analysis. Results showed that the phosphorus content was lowered from 0.1 mass% to 0.034 mass%, while the iron grade reached 59.8 mass% from 57.5 mass% by alkaline roasting with 0.05 w/w NaOH at 300 °C for 2 h, followed by wet grinding in an attritor with water for 30 seconds at room temperature. Under the experimental conditions, the dephosphorisation rate was about 54.7%, and the solution obtained by wet grinding contained 22.7 mg/L of phosphorus and 21.5 mg/L of iron. The recovery rate of iron by this process reached 99.9%. Keywords: Iron ore, phosphorus, dephosphoriszation, alkaline roasting, wet grinding

Jan 1, 2020

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By J. S. Freer

Two very successful schools on 'The design and operation of plants for the recovery of gold by activated carbon', were held from 14th to 18th October, 1985, and from 24th to 27th February, 1986, at Mintek. They were arranged by the Institute in close co-operation with Mr. Peter Bailey of Gencor, who was course leader. Computers and mathematics APCOM 87, the 20th International Symposium of the Application of Computers and Mathematics in the Mineral Industries, is to be held in Johannesburg from 19th to 23rd October, 1987. Interested people are invited to submit titles and synopses in any of the following topics or others. Papers can cover theoretical developments, practical applications, case studies, and software and hardware systems. Tunneling '88 The Institution of Mining and Metallurgy is pleased to announce the holding of 'Tunneling '88', the fifth international symposium and exhibition in the series, from 17th to 22nd April, 1988, at the Kensington Rainbow Exhibition Centre, London, England. Centenary exhibition and conference The major trade show to take place in the year of Johannesburg's centenary will be the 7th International Mining and Electrical Engineering Exhibition- ELECTRA MINING 86. The Exhibition, which is also the third-largest mining exhibition in the world, wil take place from 15th to 19th September, 1986, at the National Exhibition Centre, Crown Mines, Johannesburg. Mining electro technology The Eighth WVU International Mining Electro technology Conference is to be held in Morgantown, West Virginia, U.S.A., from 29th July to 1st August, 1986.

Jan 1, 1986

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012

By S. Maluadzi, D. Rocchi, S. Luyckx, S. S. Potgieter-Vermaak, C. Machio, J. H. Potgieter

The aim of this work was to compare the corrosion behaviour of thermal spray WC ? based coatings before and after annealing. X-ray diffraction (XRD) was used to determine the phases present in the coatings at various stages. The corrosion resistance of the coatings was measured using electrochemical and immersion corrosion tests. The results obtained from electrochemical corrosion (quantified by corrosion current density) and immersion corrosion tests showed that annealing appears to decrease the corrosion resistance of the coatings. From the XRD results it was determined that the phases that corroded preferentially were cobalt (Co), eta (Co6W6C) and W2C. Keywords: Corrosion, thermal spray, coatings, hardmetals.

Jan 1, 2006

1. OPLEIDING IN INGENIEURSWERK VIR IN G ENIEURS- IN -OPLEID IN G 1.1 llegistrasie as Ingenieur-in-opleiding 'n Gegradueerde ingenieur wat in 'n eksamen geslaag het wat die Raad erkenl, is registreerpaar as 'n ingenieur-in-opleiding kragtens die Wet op Professionele Ingenieurs2. Aansoekvorms kan van die Registrateur verkry word. Mineral processing congress The XIIIth International Mineral Processing Congress is to be held in Warsaw from 4th to 9th June, 1979. Seeing that by products and co-products are becoming of increasing importance in mineral processing operations, the theme of the Congress is to be the 'Treatment of Raw Materials with Total Utilization of All Constituents'.

Jan 1, 1979

By N. B. Strydom, P. L. Jooste, H. F. Kotze, W. H. Van Der Walt

Note: A revised method of heat acclimatization by N. B. STRYDOM, W. H. VAN DER WALT, P. L. JOOSTE, and H. F. KOTZE INTRODUCTION Climatic-room acclimatization was introduced in the gold-mining industry in 1965 and was rapidly adopted by all mines because it reduced the number of days required for heat acclimatization from 12 to 8. The method has been adequately described in previous papers1, 2 but, briefly, requires four hours of heat exposure per day while the work rate is progessively increased from 35 W on Day 1 to 70 W on Days 7 and 8. Several attempts to shorten

Jan 6, 1976

By P. Ramphisa

In South Africa reprocessing used oil into industrial fuel is commercially attractive. The reprocessed product is sold as a substitute for heavy fuel oil that is derived from crude oil (Rose Foundation, 2008). The objective of this investigation is to evaluate the use of petroleum products such as oil, petrol and diesel in Driefontein Gold Mine. The recovery of oil through recycling has costs implications to the mine while the release of petroleum hydrocarbons due to the poor management of the use of petroleum products has potential to cause pollution and negatively affect soil and water. Environmental legislation such as the Minerals and Petroleum Resources Development Act (Act 28, 2002) requires that such negative impacts to the environment be rehabilitated. The rehabilitation cost of pollution caused by petroleum products to the environment increases operational costs in business. Field assessment is conducted to identify the main sources of petroleum product contamination such as leaks in piping, overfills and petroleum spills. The areas that require mitigation would be mapped in the study. Recommendations for mitigation measures will focus on using the best practicable environmental option (BPEO) as well as the best available technology not exceeding excessive cost (BATNEEC). The recovery of oil from the mining industry is generally low and very poor. In this study, the effect of proper management of petroleum products to the mine?s operational costs is investigated and compared to there mediation costs of the impacts caused due to poor management of these products. The study investigates the financial benefit that could be obtained from proper environmental practices and efficient usage of petroleum products in the mining.

Jan 1, 2009

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020

By Z. M. Beiranvand, M. Moghaddasi, A. Naeimi, Y. Naami, M. Raoufi

Titanium iron oxide and nickel-chromium coatings were applied on low-carbon steel substrates using the high-velocity oxygen fuel thermal spraying process. The microstructure, phase composition, and hardness of the coatings were analysed using scanning electron microscopy, x-ray diffraction, and microhardness tests. The phase analysis confirmed the formation of oxide compounds in the coatings. The average microhardness values for titanium iron oxide and titanium iron oxide-nickel-chromium coatings were measured at 580 HV and 970 HV, respectively, under a 100 g load. The corrosion resistance of the coatings was evaluated in a 3.5% sodium chloride solution using electrochemical impedance spectroscopy (EIS) and polarisation tests. The results indicated that the nickel-chromium composition exhibited superior corrosion resistance, which was attributed to its low porosity, preventing solution diffusion into the substrate. Wear behaviour was assessed using a pin-on-disk test with a tungsten carbide pin as the counterbody. The incorporation of nickel-chromium into the titanium iron oxide coating resulted in an 80% reduction in weight loss, indicating significant improvement in wear resistance. These findings suggest that nickel-chromium-modified titanium iron oxide coatings enhance both corrosion and wear resistance, making them promising candidates for industrial applications.

May 8, 2026

By P. G. H. Pistorius, D. S. Konadu, G. Lubbe

The aim of this investigation was to determine whether the composition of a shielded-metal arc-welding electrode coating affected the low-temperature impact toughness of austenitic stainless-steel weld metal. It is generally accepted that increases in the δ-ferrite and nitrogen contents result in a decrease in toughness at low temperatures. Weld metal from electrodes with a basic coating also generally exhibit better toughness than those from rutile (acidic) electrodes. An increase in basicity was expected to decrease the number and size of inclusions, which in turn provides a tougher weld metal. Three commonly available potassium–rutile E308L electrodes were used, complying with the E308L-16 and E308L-17 specifications. Analysis of the electrode coatings showed very similar chemistry and basicity. Significant differences in the inclusion contents of the weld metals were observed: the E308L-17 weld metal had a lower inclusion content (1.4% by volume) than the E308L-16 weld metal (3.7%). The former had higher impact toughness at all temperatures, despite a slightly higher nitrogen content. Regression analysis confirmed that the inclusion content had a significant effect on the impact toughness at all temperatures.

Jul 2, 2022

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

By R. P. King, L. C. Woollacott

To date developments in the simulation of carbon-in-pulp (CIP) adsorption circuits have focused primarily on the modeling of adsorption. This series of three papers describes a development in a direction that has received less attention, i.e. the need for a detailed description of the movement of carbon and slurry in continuous CIP and carbon-in-leach (CIL) plants. A new simulator has been developed based on the population-balance approach for modeling the movement of carbon and slurry. Existing adsorption and leaching models are evaluated in this paper in order to establish which are appropriate for use in the new simulator. The details of the simulator are given in Part 2 of this series.

Jan 1, 1990